Home › Vehicle Exterior › BODY PANEL › REAR FLOOR PAN
BM38G0E _01 Vehicle Exterior _101965 BODY PANEL _0472905 REAR FLOOR PAN F

BODY PANEL  REAR FLOOR PAN  CUT AND JOIN REPLACEMENT SECTIONS  


K161943

With the body lower back panel cut and join replacement sections (small areas) and rear floor crossmember upper gusset assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108829

Cut Location

a.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K161320C01
0,0 0,0 false
K108837

Adhesive - -


K161321C01
6.781,1.635 7.094,1.792 0.313,0.156 10 false *a
*a 400 mm (15.75 in.) - -


K161322C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A LH Side - -


K161323C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A RH Side - -




INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108829

Cut Location
K108834

Body Sealer

a.

Cut the new part so that it overlaps the previous cut location by approximately 30 mm (1.18 in.).

K161324C01
1.667,4.083 1.833,4.083 1.833,4.083 2.167,3.583 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 1.479,4.01 1.792,4.167 0.313,0.156 10 false *1 5.396,1.292 5.708,1.448 0.313,0.156 10 false *a
*A Upper Face - -
*1 REAR FLOOR PAN - -
*a 370 mm (14.57 in.) - -



b.

Before temporarily installing the new parts, weld the rear floor pan, rear floor panel reinforcement, rear floor side plate and weld bolts with the standard number of welding points.

K161325C01
0.583,0.167 6.583,6.583 6,6.417 0.583,3.583 6.583,3.583 false 3.698,0.969 4.083,0.417 4.083,0.417 4.25,0.417 false 1.833,2.917 2,2.917 2,2.917 2.25,2.5 false 5.333,6 4.51,4.427 false 5.5,6 5.333,6 5.333,6 4.5,5.01 false 0.667,0.25 0.979,0.406 0.313,0.156 10 false *A 0.667,3.677 0.979,3.833 0.313,0.156 10 false *B 1.646,2.844 1.958,3 0.313,0.156 10 false *1 4.313,0.344 4.625,0.5 0.313,0.156 10 false *2 5.563,5.927 5.875,6.083 0.313,0.156 10 false *3
*A Upper Face *B Lower Face
*1 REAR FLOOR PAN *2 REAR FLOOR PANEL REINFORCEMENT
*3 WELD BOLTS - -


K161326C01
0.167,0.333 7,3.5 6.833,3.167 3.583,3.5 3.583,0.333 false 1.594,1.396 1.333,0.917 1.333,0.917 1.167,0.917 false 5.521,1.406 5.75,0.917 5.75,0.917 5.917,0.917 false 0.25,0.417 0.563,0.573 0.313,0.156 10 false *A 3.667,0.427 3.979,0.583 0.313,0.156 10 false *B 0.979,0.854 1.292,1.01 0.313,0.156 10 false *1 5.969,0.865 6.281,1.021 0.313,0.156 10 false *1
*A LH Side *B RH Side
*1 REAR FLOOR SIDE PLATE - -



c.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K161320C01
0,0 0,0 false
K108837

Adhesive - -



d.

Perform plug-welding in the area where the panel are overlapped. Apply body sealer to each panel.

HINT:
·

Confirm that the panels are securely welded together.

·

Apply body sealer in an even, continuous bead.



K161327

K161328C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A LH Side - -


K161329C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A RH Side - -



e.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting/coating)


f.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.