Home › Vehicle Exterior › BODY PANEL › CAB MOUNTING NO.4 BRACKET
BM38G0E _01 Vehicle Exterior _101965 BODY PANEL _0472917 CAB MOUNTING NO.4 BRACKET F

BODY PANEL  CAB MOUNTING NO.4 BRACKET  ASSEMBLY REPLACEMENT  


K161953

K161264

HINT:
·

Use the same procedure for the RH and LH.

·

The procedure listed below is for the RH.



REMOVAL


Symbol Meaning
K108826

Cut with Disc Sander etc.

K161265C02
1.708,1.115 2.021,1.271 0.313,0.156 10 false *A 1.333,3.094 1.646,3.25 0.313,0.156 10 false *B 1.313,1.5 1.625,1.656 0.313,0.156 10 false *C 1.708,3.458 2.021,3.615 0.313,0.156 10 false *A 1.708,5.552 2.021,5.708 0.313,0.156 10 false *A 1.333,5.198 1.646,5.354 0.313,0.156 10 false *C
*A FRONT *B UPPER
*C RH - -



INSTALLATION


Symbol Meaning
K108830

Fillet Weld

a.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


b.

Make sure that proper welding can be performed by setting up the welding conditions as necessary before performing work.


c.

Before installing the upper body, confirm the alignment of the upper body and frame.


d.

To prevent heat deformation, weld the right and left side of each part before continuing to the next part.


e.

Make sure that the welding bead at A is overlapped.

K161266C01
4.667,1.917 4.5,1.917 4.5,1.917 4.156,1.531 false 2.083,2.667 2.25,2.667 2.25,2.667 2.979,3.479 false 4.333,3.469 5,2.667 5,2.667 5.167,2.667 false 1.708,1.104 2.021,1.26 0.313,0.156 10 false *A 1.333,3.094 1.646,3.25 0.313,0.156 10 false *B 1.313,1.5 1.625,1.656 0.313,0.156 10 false *C 4.698,1.844 5.01,2 0.313,0.156 10 false *1 3.417,0.396 3.729,0.552 0.313,0.156 10 false *a 3.74,0.406 4.052,0.563 0.313,0.156 10 false *b 2.99,2.479 3.302,2.635 0.313,0.156 10 false *c 2.01,3.823 2.323,3.979 0.313,0.156 10 false *d 2.271,3.813 2.583,3.969 0.313,0.156 10 false *e 4.177,2.344 4.49,2.5 0.313,0.156 10 false *f 3.729,6.354 3.948,6.552 0.219,0.198 10 false *g 3.479,6.344 3.792,6.5 0.313,0.156 10 false *h 4.896,3.813 5.208,3.969 0.313,0.156 10 false *e 5.115,3.823 5.427,3.979 0.313,0.156 10 false *d 3.188,6.354 3.406,6.552 0.219,0.198 10 false *g 1.688,3.458 2,3.615 0.313,0.156 10 false *A 1.708,5.552 2.021,5.708 0.313,0.156 10 false *A 1.323,5.188 1.635,5.344 0.313,0.156 10 false *C 1.958,2.583 2.115,2.781 0.156,0.198 10 false A 5.208,2.573 5.365,2.771 0.156,0.198 10 false A
*A FRONT *B UPPER
*C RH - -
*1 CAB REAR MOUNTING BRACKET SUB-ASSEMBLY - -
*a 27 +/- 5 mm (1.06 +/- 0.20 in.) *b 23 +/- 5 mm (0.91 +/- 0.20 in.)
*c 182 mm (7.17 in.) *d 12 mm (0.47 in.)
*e 5 mm (0.20 in.) *f 200 mm (7.87 in.)
*g 5 +/- 5 mm (0.20 +/- 0.20 in.) *h 53 mm (2.09 in.)



f.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.