Home › Vehicle Exterior › BODY PANEL › BODY LOWER BACK PANEL
BM38G0E _01 Vehicle Exterior _101965 BODY PANEL _0472904 BODY LOWER BACK PANEL F

BODY PANEL  BODY LOWER BACK PANEL  CUT AND JOIN REPLACEMENT SECTIONS (LARGE AREAS)  


K161941

With the back door opening side reinforcement cut and join replacement sections removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location

a.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K161299C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A LH - -
K108837

Adhesive - -


K161300C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 4.885,3.167 5.198,3.323 0.313,0.156 10 false *a
*A LH - -
*a 115 mm (4.53 in.) - -


K161301C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A LH - -


K161302C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A LH - -


K161303C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A LH - -



b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K161304C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A RH - -
K108837

Adhesive - -


K161305C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 2.135,3.167 2.448,3.323 0.313,0.156 10 false *a
*A RH - -
*a 112 mm (4.41 in.) - -


K161306C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A RH - -


K161307C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A RH - -


K161308C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A RH - -




INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K161299C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A LH - -
K108837

Adhesive - -


K161309C01
3.667,3.083 3.5,3.083 3.5,3.083 3.25,2.781 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 3.719,3.021 4.031,3.177 0.313,0.156 10 false *1
*A LH - -
*1 LOWER BACK PANEL SUB-ASSEMBLY - -


K161310C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A LH - -


K161311C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A LH - -


K161312C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A LH - -



d.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K161304C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A RH - -
K108837

Adhesive - -


K161313C01
3.667,3.083 3.5,3.083 3.5,3.083 3.25,2.781 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 3.719,3.021 4.031,3.177 0.313,0.156 10 false *1
*A RH - -
*1 LOWER BACK PANEL SUB-ASSEMBLY - -


K161314C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A RH - -


K161315C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A RH - -


K161316C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A RH - -



e.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


f.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting/coating)


g.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.