Home › Vehicle Interior › SEAT › POWER SEAT CONTROL SYSTEM
NM38G0E _58 Vehicle Interior _101087 SEAT _0470425 POWER SEAT CONTROL SYSTEM CO CONTROL F

SEAT  POWER SEAT CONTROL SYSTEM  CONTROL  SEAT CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components in the power seat control system have the following functions:

Models without Position Memory Function (Driver Seat/Front Passenger Seat)
Component Outline
Front Power Seat Switch Operates the motors in accordance with the signals from the front power seat switch.

Models with Position Memory Function (Driver Seat)
Component Outline

*1: Models with 10-speed automatic transmission

*2: Models with 6-speed automatic transmission

*3: Models with power tilt and telescopic system

*4: Driver seat side

*5: Models with headup display

Front Power Seat Switch Sends motor operation signal to the position control ECU assembly.
Seat Memory Switch Sends position memory function signals to the main body ECU.
Position Control ECU Assembly
·

Receives signals from the main body ECU, etc. via CAN communication and determines operation conditions for the memory system.

·

Inputs signals from the position sensors for the seat adjusters in the driver seat and detects the slide, reclining, front vertical and vertical lifter positions for the driver seat.

·

Receives seat memory switch operation signals from the main body ECU via CAN communication and memorizes/recalls the driver seat position.

·

Sounds the built-in buzzer when the memorization operation completes or recall starts.


Main Body ECU (Multiplex Network Body ECU)
·

Inputs signals from the front door courtesy light switch assembly (driver seat side) and sends driver door opening and closing signals to the position control ECU assembly via CAN communication.

·

Sends shift position signals from the ECT-ECU*1/ ECM*2 to the position control ECU assembly via CAN communication.

·

Inputs key ID signals and door lock/unlock signals and sends key ID and door lock/unlock signals to the position control ECU assembly via CAN communication.

·

Detects that the power switch is on (IG) and sends signals to the position control ECU assembly via CAN communication.

·

Sends key code confirmation signals to the position control ECU assembly via CAN communication.


Multiplex Tilt and Telescopic ECU*3
·

Receives signals from the main body ECU and memorizes and recalls the steering position.

·

Detects the position information of the tilt and telescopic motors.


Front Door Courtesy Light Switch Assembly (Driver Door) Detects the opening and closing of the driver door and sends signals to the main body ECU.
Certification ECU (Smart Key ECU Assembly) Sends smart memory call recall command signals to the main body ECU via CAN communication.
ECT-ECU*1 Sends shift position signal to the position control ECU assembly.
ECM*2
Combination Meter Assembly Sends vehicle speed signals to the position control ECU assembly.
Front Seat Inner Belt Assembly*4 Detects whether the driver's seat belt is fastened and outputs this information to the position control ECU assembly.
Outer Mirror Control ECU Assembly LH/ RH
·

Inputs signals from each position sensor inside the outer rear view mirror and detects the mirror surface position of the outer rear view mirror.

·

Receives signals (memorize/recall commands) from the main body ECU via CAN communication and memorizes/recalls the mirror surface position of the outer rear view mirror.

·

Sends operation signals from the seat memory switch to the main body ECU via CAN communication.*4


Headup Display (Meter Mirror Sub-assembly)*5
·

Meter Mirror ECU


Receives signals (memorize/recall commands) from the main body ECU via CAN communication and memorizes/recalls the display position of the headup display.

HINT:

The seat position memory system functions only when the my setting system is off.


Rear No. 2 power seat control function
Component Outline
Rear Power Seat Switch Operates the motors of rear No. 2 seat.
No. 1 Fold Seat Switch Assembly (Rear No. 2 Seat Left Side Switch)
No. 2 Fold Seat Switch Assembly (Rear No. 2 Seat Right Side Switch)
Fold Seat Switch Assembly (Luggage Side Switch)
Fold seat control ECU
·

Receives signals from each operation switch, drives the motor, and performs fold, return and reclining operations.

·

Sounds the internal buzzer if operation conditions have not been established or if jamming is detected.


Reclining Motor Operates the motors in accordance with the signals from the rear power seat switch.
Reclining Motor/ Cushion Motor Operates the motors in accordance with the signals from the No. 1 fold seat switch assembly, No. 2 fold seat switch assembly and fold seat switch assembly.



SYSTEM CONTROL


a.

Power Seat Control System (Driver Seat/ Front Passenger Seat)

i.

The power seat control system has the following functions:

System Outline

*: Driver seat

Power Seat Control The user can perform seat slide, seat reclining, front vertical, seat lifter, and lumbar support* adjustments by operating the front power seat switch.



b.

Position Memory Function (Driver Seat)

i.

The position memory has the following functions:

Function Outline
Memory The position memory function can memorize 3 different seat positions.
Recall The recall function can recall 3 different memorized seat positions.
Memory Call The memory call function, which utilizes the key IDs, is used to memorize and recall the optimal driving position for a person possessing the electrical keys.
Automatic Away The seat slide moves rearward, making it easier to exit the vehicle.
Automatic Return The automatic return function automatically returns the seat to the previous position before starting the vehicle.


ii.

The position memory function works in combination with the following systems, ensuring usability and enabling easy entering or exiting of the vehicle.

System Outline
Power Tilt and Telescopic System The multiplex tilt and telescopic ECU memorizes the steering column position and recalls it when all conditions are met.
Headup Display System The meter mirror sub-assembly memorizes the headup display position and recalls it when all conditions are met.
Outer Mirror Control ECU Assembly LH/ RH The outer mirror control ECU assembly memorizes the mirror surface position and recalls it when all conditions are met.


iii.

The position memory function operating conditions are as follows:

Function Condition Operation
Memory Either of the following conditions is met while the ignition switch is ON:
·

Button 1, 2 or 3 (seat memory switch) is pushed within 3 seconds after the "SET" button is pushed.


·

Stores the seat position.

·

When the memory setting is completed, the buzzer sounds for 0.5 seconds.


Recall
·

Button 1, 2 or 3 (seat memory switch) is pushed within 180 seconds after the driver door has been opened while the ignition switch is off.

·

Button 1, 2 or 3 (seat memory switch) is pushed.


·

The seat position that was memorized in the position control ECU assembly is recalled.

·

The buzzer sounds for 0.1 seconds once the stored seat position is reproduced.


·

Ignition switch is ON.

·

Shift position is in P.

·

Button 1, 2 or 3 (seat memory switch) is pushed.


Button 1, 2 or 3 (seat memory switch) is pushed within 60 seconds after the ignition switch has been turned off and the driver door has been closed.
Memory Call
·

A key ID is registered to button 1, 2 or 3 (seat memory switch).

·

Ignition switch is off.

·

The inside of the outside door handle is touched or the electrical keys unlock button is pushed to unlock, and then the driver door is opened.


·

The seat position that was memorized in the position control ECU assembly is recalled.

·

The buzzer sounds for 0.1 seconds once the stored seat position is reproduced.


Automatic Away
·

Ignition switch is turned off.

·

Driver seat belt is not fastened.


The seat automatically moves rearward up to 50 mm (1.97 in.).
Automatic Return
·

Seat is in the automatic away position.

·

Ignition switch is turned on (IG).

·

Fasten the driver seat belt.


The seat automatically returns to the previous seat position.



c.

Power Seat Control System (Rear No. 2 Seat)

i.

The power seat control system has the following functions:

System Outline
Power Seat Control The user can perform seat reclining adjustment by operating the rear power seat switch and fold seat switch assembly (Luggage Side Switch).



d.

Fold Seat Control System (Rear No. 2 Seat)

i.

The fold seat control system has the following functions:

System Outline
Power Seat Control The rear No. 2 seat can be folded/returned by operating the No. 1 fold seat switch assembly, No. 2 fold seat switch assembly and fold seat switch assembly.


ii.

Luggage compartment expansion operation

·

When any of the following conditions is established, the fold seat switch assembly can be operated to recline the seatback to the front end point position within its adjustable reclining range, expanding the luggage compartment.

*: When operating fold seat switch assembly (Luggage Side Switch)

·

Seat occupied and ignition switch off

·

Seat occupied, ignition switch ON and shift range in P

·

Back door open*

·

No other operation switches are pressed




V129828C02
3.354,1.542 4.115,0.74 true 4.083,0.583 4.396,0.74 0.313,0.156 10 false *a 3,3.354 3.313,3.51 0.313,0.156 10 false *b 0.063,3.479 0.375,3.635 0.313,0.156 10 false *c
*a Front End Point Position within Adjustable Reclining Range *b Luggage Compartment Expansion
*c The illustration shown is example only. - -



iii.

Power fold/return operation

·

When any of the following conditions is established, the seat can be folded or returned by operating the switches in the No. 1 fold seat switch assembly, No. 2 fold seat switch assembly and fold seat switch assembly.

*1: When operating No. 1 fold seat switch assembly and No. 2 fold seat switch assembly

*2: When operating fold seat switch assembly (Luggage Side Switch)

·

Ignition switch OFF

·

Ignition switch ON and shift range in P

·

Rear door*1 or back door*2 on operation switch side open

·

No other operation switches are pressed




V129829C02
2.094,3.844 2.51,3.583 true 2.854,0.594 3.167,0.75 0.313,0.156 10 false *A 1.167,3.198 1.479,3.354 0.313,0.156 10 false *B 5.729,3.125 6.042,3.281 0.313,0.156 10 false *C 2.5,2.677 2.813,2.833 0.313,0.156 10 false *a 4.563,2.813 4.875,2.969 0.313,0.156 10 false *b 2.49,3.458 2.802,3.615 0.313,0.156 10 false *c 0.063,5.542 0.375,5.698 0.313,0.156 10 false *d 3.385,3.885 3.698,4.042 0.313,0.156 10 false *a
*A Occupied *B Luggage Compartment Expanded
*C Folded - -
*a Fold switch continuously pressed. *b Return switch continuously pressed.
·

The return operation will not automatically return the headrest.


*c Front end point position within adjustable reclining range. *d The illustrations shown are examples only.



iv.

Fold operation

·

If the seatback is collapsed ahead of the front end point position within its adjustable reclining range and the fold switch is pressed, the fold seat control ECU sounds the internal buzzer 2 times and operates the reclining motor, and then begins the fold operation.

·

When the seatback reclines forward to the position where the seat cushion can be folded, the fold seat control ECU operates the cushion motor and begins the seat cushion fold operation. The fold operation will continue as long as the fold switch continues to be pressed. Releasing the switch will stop operation and sound the buzzer to notify the user that operation has not been completed.*

HINT:

*: If the fold switch is pressed but operation conditions have not been established, the buzzer will sound and the fold operation will not be performed.



V129830C02
1.948,2.073 1.396,3.271 true 1.948,1.729 0.854,3.188 true 2.5,1.719 2.938,3.292 true 3.667,1.844 4.396,3.292 true 4.24,2 5.24,1.021 true 0.74,3.219 1.052,3.375 0.313,0.156 10 false *1 1.281,3.302 1.594,3.458 0.313,0.156 10 false *2 2.896,3.323 3.208,3.479 0.313,0.156 10 false *3 4.396,3.302 4.708,3.458 0.313,0.156 10 false *4 5.271,0.896 5.583,1.052 0.313,0.156 10 false *5 0.083,3.427 0.396,3.583 0.313,0.156 10 false *a
*1 Gear Box *2 link
*3 Cushion Motor *4 Slide Pin
*5 Slide Rail - -
*a The illustration shown is example only. - -


·

If it is determined based on signals from the pulse sensors (Hall ICs) inside the seatback and seat cushion that these parts have entered the area where folding is complete, and then the fold seat control ECU determines that the cushion motor is locked, the fold seat control ECU stops supplying power to the reclining motor and cushion motor, sounds the internal buzzer 2 times, and then stops the fold operation.*

HINT:

*: The internal buzzer will sound 2 times and the fold operation will be stopped even if the fold switch is released in the area where folding is complete.




v.

Return operation

·

If the return switch is pressed when the seat is folded, the fold seat control ECU sounds the internal buzzer 2 times, operates both the reclining motor and cushion motor, and then begins the return operation. The return operation will continue as long as the return switch continues to be pressed. Releasing the switch will stop operation and sound the buzzer to notify the user that operation has not been completed.*

HINT:

*: If the return switch is pressed but operation conditions have not been established, the buzzer will sound and the return operation will not be performed.


·

If it is determined based on signals from the pulse sensors (Hall ICs) inside the seatback and seat cushion that these parts have entered the return complete area, and then the fold seat control ECU determines that the reclining motor is locked, the fold seat control ECU stops supplying power to the reclining motor and cushion motor, sounds the internal buzzer 2 times, and then stops the return operation.*

HINT:

*: The internal buzzer will sound 2 times and the return operation will be stopped even if the return switch is released in the return complete area.




vi.

Overload detection operation

·

If foreign matter becomes jammed or the weight of the luggage prevents operation when the power fold seat is operating, the pulse width of the pulse sensor (Hall IC) installed in the reclining motor or cushion motor changes, which causes the fold seat control ECU to determine that there is an overload.

·

If an overload is detected, the system immediately stops operation or begins operating in reverse, and then sounds the buzzer inside the fold seat control ECU.



vii.

Operation following overload detection (during fold operation)

·

If the fold seat control ECU detects an overload during a fold operation, it stops operation or operates in reverse in the return direction.

·

Reverse operation will be stopped if any of the following conditions is established.

·

The seatback reaches a position outside the return operation range

·

Any switch is pressed

·

The fold seat control ECU detects that the motor is locked

·

The fold seat control ECU detects an overload





viii.

Operation following overload detection (during return operation)

·

If the fold seat control ECU detects an overload during a return operation, it operates in reverse in the fold direction.

·

Reverse operation will be stopped if any of the following conditions is established.

·

The seatback reverses 10°

·

Any switch is pressed

·

The fold seat control ECU detects that the motor is locked

·

The fold seat control ECU detects an overload







FUNCTION


a.

Seat Position Detection Method

i.

Power Seats with Position Memory Function

1.

The hall IC installed on the power seat motor generates pulses corresponding to the speed of the motor. These pulses are then picked up by the position control ECU assembly in order to detect the seat position.

Y103923C03
1.74,1.448 1.74,0.677 1.74,0.677 1.313,0.677 true 2.938,1.208 2.938,0.333 2.938,0.333 3.302,0.333 true 6.25,2.594 5.406,2.594 true 1.635,2.594 0.792,2.594 true 6.292,2.458 6.531,2.677 0.24,0.219 10 false *2 0.594,2.49 0.823,2.781 0.229,0.292 10 false *1 3.344,0.219 3.573,0.438 0.229,0.219 10 false *a 1.115,0.573 1.354,0.792 0.24,0.219 10 false *3
*1 Power Seat Motor *2 Position Control ECU Assembly
*3 Hall IC - -
*a Current Pulsation Generated by Motor - -






DIAGNOSIS


a.

The position control ECU assembly has a diagnosis function. It stores a record of any power seat control system malfunctions in its memory in the form of Diagnostic Trouble Codes (DTCs).


b.

The position control ECU assembly outputs malfunction data and 5-digit DTCs to the Global TechStream (GTS).


c.

The 5-digit DTCs can be read by connecting the GTS to the DLC3. For details, refer to the Repair Manual.