Home › Drivetrain › JF2BM (TRANSFER / 4WD / AWD) › FOUR WHEEL DRIVE CONTROL SYSTEM
NM38G0E _52 Drivetrain _102374 JF2BM TRANSFER / 4WD / AWD _0473729 FOUR WHEEL DRIVE CONTROL SYSTEM CO CONTROL F

JF2BM TRANSFER / 4WD / AWD  FOUR WHEEL DRIVE CONTROL SYSTEM  CONTROL  FOUR WHEEL DRIVE CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Models with AC60F automatic transmission

*2: Models with AJA0F automatic transmission

Transfer Shift Actuator Assembly High-low Shift Motor Switches the transfer gear ratio between high and low in accordance with signals from the 4 wheel drive control ECU.
High-low Limit Switch Detects the position of the high-low shift motor and transmits a signal to the 4 wheel drive control ECU.
Center Differential Lock Shift Motor Switches the center differential between free and lock in accordance with signals from the 4 wheel drive control ECU.
Center Differential Lock Limit Switch Detects the position of the center differential lock shift motor and transmits a signal to the 4 wheel drive control ECU.
Center Differential Lock Position Switch Detects the lock position of the center differential and transmits a signal to the 4 wheel drive control ECU and so on.
Integration Control Assembly Transfer Position Switch Switches the drive mode and transmits a signal to the 4 wheel drive control ECU.
Center Differential Lock Switch Switches the center differential between free and lock and transmits a signal to the 4 wheel drive control ECU.
4 Wheel Drive Control ECU Controls each shift motor in response to a signal from each switch and ECU.
ECM*1 Transmits a shift position signal to the 4 wheel drive control ECU via CAN.
Transmission Control ECU Assembly*2
Brake Actuator Assembly No. 2 Skid Control ECU Transmits a vehicle speed signal to the 4 wheel drive control ECU via CAN.
Combination Meter Assembly Low Speed Four-wheel Drive Indicator
·

Blinks while switching the transfer gear ratio between high and low, and turns on when in low.

·

Blinks when the switching conditions are not met while switching the transfer gear ratio between high and low.


Center Differential Lock Indicator
·

Blinks while switching the center differential between free and lock, and turns on when in lock.

·

Blinks when the switching conditions are not met while switching the center differential between free and lock.


VSC OFF Indicator Turns on in accordance with the drive mode when VSC function is not operating.
Buzzer Sounds when the switching conditions are not met while switching the drive mode.


OPERATING CONDITION


a.

The drive mode switching pattern of the 4WD system is as shown in the illustration below:

X102268E07
3.25,0.688 4.031,1.052 0.781,0.365 10 false Pattern E 2.167,0.833 2.667,1.188 0.5,0.354 10 false H4F 4.74,0.833 5.219,1.188 0.479,0.354 10 false L4F 2.208,2.563 2.75,2.906 0.542,0.344 10 false H4L 4.76,2.563 5.271,2.896 0.51,0.333 10 false L4L 3.281,1.115 4.031,1.5 0.75,0.385 10 false Pattern F 2.49,1.656 3.313,2.031 0.823,0.375 10 false Pattern B 1.469,1.656 2.167,2.042 0.698,0.385 10 false Pattern A 5.052,1.604 5.885,1.958 0.833,0.354 10 false Pattern D 4.021,1.625 4.729,1.979 0.708,0.354 10 false Pattern C 3.271,2.469 4.063,2.823 0.792,0.354 10 false Pattern G 3.292,2.854 4.094,3.198 0.802,0.344 10 false Pattern H 0.104,0.063 2.76,0.49 2.656,0.427 10 false Drive Mode Switching Pattern 0.354,3.219 3.896,3.583 3.542,0.365 10 false H4F: High speed 4WD and center differential Free 0.396,3.969 3.76,4.344 3.365,0.375 10 false L4F: Low speed 4WD and center differential Free 0.375,3.594 3.823,3.969 3.448,0.375 10 false H4L: High speed 4WD and center differential Lock 0.396,4.344 3.833,4.729 3.438,0.385 10 false L4L: Low speed 4WD and center differential Lock


b.

When the vehicle speed is 100km/h (62mph) or less, free-lock switching of the center differential lock (switching patterns A to D) is available while the vehicle is running.


c.

The transfer gear ratio can be switched between high and low (switching patterns E to H) only when the vehicle is stationary and the shift lever is in N.


d.

VSC function in the brake control system may be stopped, depending on the drive mode. For details, see the Brake Control/Dynamic Control Systems section.



DIAGNOSIS


a.

When the 4 wheel drive control ECU detects a malfunction, the 4 wheel drive control ECU records the malfunction and memorizes the information related to the fault.


b.

The 4 wheel drive control ECU will also store the Diagnostic Trouble Codes (DTCs) of the malfunctions. The DTCs stored in the 4 wheel drive control ECU are output to the Global TechStream (GTS) via the DLC3.


c.

For details, refer to the Repair Manual.