Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
NM38G0E _59 Vehicle Exterior _101089 WIPER / WASHER _0473774 WIPER AND WASHER SYSTEM DE DETAILS F

WIPER / WASHER  WIPER AND WASHER SYSTEM  DETAILS  WASHER NOZZLE  


CONSTRUCTION


a.

Front Washer Nozzle

i.

Diffuser type washer nozzle sub-assemblies are located under the engine hood to ensure good appearance.


ii.

With the adoption of the diffuser type washer nozzle sub-assemblies, only a small amount of washer fluid is needed to spray over a large area, achieving excellent wiping performance.

Y273586C01
2.167,1.396 1.938,0.708 true 0.875,1.99 0.406,1.344 true 3.354,2.542 3.823,1.958 true 0.281,1.177 0.594,1.333 0.313,0.156 10 false *1 1.813,0.542 2.125,0.698 0.313,0.156 10 false *a 6.083,0.635 6.396,0.792 0.313,0.156 10 false *b 6.427,1.656 6.74,1.813 0.313,0.156 10 false *c 0.063,3.51 0.375,3.667 0.313,0.156 10 false *d 3.229,2.521 3.542,2.677 0.313,0.156 10 false *1
*1 Washer Nozzle Sub-assembly - -
*a Washer Fluid Spray Area *b Fluid Volume
*c Main Flow Center *d The illustration shown are example only.


HINT:

Diffuser type washer nozzle sub-assemblies cannot be adjusted because of their structure. Do not attempt to adjust the nozzles as it could damage them. If adjustment is necessary, adjust the spray pattern by replacing the nozzles with those selected from the 3 part numbers available. For details, refer to the Repair Manual.




b.

Rear Washer Nozzle

i.

A spray type rear washer nozzle is attached to the rear spoiler.

Y273587C01
2.719,0.948 2.583,0.427 true 3.604,1.51 2.802,1.271 true 3.385,2.406 2.823,2.135 true 2.479,0.24 2.792,0.396 0.313,0.156 10 false *1 3.635,1.458 3.948,1.615 0.313,0.156 10 false *2 3.427,2.375 3.74,2.531 0.313,0.156 10 false *a 5.219,2.042 5.531,2.198 0.313,0.156 10 false *b 0.042,2.479 0.354,2.635 0.313,0.156 10 false *c 5.854,1.271 6.167,1.427 0.313,0.156 10 false *a
*1 Rear Spoiler *2 Rear Washer Nozzle
*a Washer Fluid Spray Area *b View from Top Side
*c The illustration shown are example only. - -




c.

Washer Nozzle Heater (Models with Washer Nozzle Heater)

i.

When the outside temperature meets or falls below a fixed level, the PTC heater is activated based on signals from the washer nozzle heater relay to prevent water inside the nozzle from freezing and blocking the washer fluid.

Y237444C03
6.448,2.771 6.083,1.563 true 3.583,2.042 3.896,2.24 0.313,0.198 10 false A 0.104,2.042 0.417,2.24 0.313,0.198 10 false A 1.813,3.365 2.125,3.563 0.313,0.198 10 false *1 5.781,3.375 6.094,3.573 0.313,0.198 10 false *a 5.969,1.396 6.281,1.594 0.313,0.198 10 false *2
*1 Washer Nozzle Sub-assembly *2 PTC Heater
*a A - A Cross Section - -