Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
NM38G0E _59 Vehicle Exterior _101089 WIPER / WASHER _0473774 WIPER AND WASHER SYSTEM GE GENERAL F

WIPER / WASHER  WIPER AND WASHER SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

Front Wiper and Washer System

i.

The windshield wiper motor assembly and wiper link assembly are mounted in a modular frame, reducing wiper operation sound and reducing variations in the wiping range.


ii.

The rain sensing function is controlled by the main body ECU (multiplex network body ECU) and rain sensor installed to the upper area of the windshield glass, which automatically operate the wipers when rain is detected.*

*: Models with rain sensing function


iii.

The vehicle speed-sensing, adjustable interval function is controlled by the windshield wiper relay assembly, and it automatically changes the wiper operation interval time according to the vehicle speed and interval time adjuster.*

*: Models without rain sensing function


iv.

Diffuser type washer nozzle sub-assemblies are provided under the engine hood to ensure a good appearance.


v.

A graphite coating is applied to the surface of the wiper rubber, reducing inversion noise and wiper flutter while the wipers are operating.


vi.

A washer nozzle heater is used, depending on the models.



b.

Rear Wiper System

i.

The rear wiper system has a washer-linked wiper function and intermittent interval function.


ii.

By using a resin rear wiper arm, a unified rear wiper blade look has been achieved.



c.

Washer Fluid Level Warning Function

i.

A warning message display function, which shows a warning message on the combination meter assembly when the washer fluid is low, is provided.



d.

Headlight Cleaner System

i.

A headlight cleaner system is provided on some models.


ii.

A headlight cleaner system is used to allow optimal lighting effectiveness to be maintained.



e.

Camera Cleaner System (Models with Camera Cleaner System)

i.

A camera cleaner system is used.


ii.

The camera cleaner system uses a nozzle installed on top of the rear television camera assembly to spray washer fluid onto the surface of the camera lens, cleaning off foreign matter that is attached to it (such as water, mud, snow and snow-melting agents) and improving the visibility of the camera image.




PRECAUTION


a.

Camera Cleaner System

i.

Knowledge

1.

If there is a sufficient amount of washer fluid but it does not spray out, check the nozzle for blockages.

2.

The camera cleaner system cleans off foreign matter that is attached to the surface of the camera lens. Therefore, it cannot clean off ice, snow, or other foreign matter that is displayed in the camera image if the foreign matter is attached to surfaces near the camera.

3.

Do not subject the camera to sudden temperature changes such as by pouring hot water into the camera under cold weather.

4.

The washer tank is shared with the windshield washer, so if the camera cleaner system is frequently used, the washer fluid will need to be replaced more often.



ii.

Cautions

1.

During camera cleaner system operation, the sprayed washer fluid may make it difficult to see the camera image. Directly check the surrounding conditions in order to ensure safe driving.

2.

If washer fluid remains on the surface of the camera lens after the camera cleaner system operates, the image may become difficult to see at night depending on the headlight height and angle of vehicles to the rear.

3.

Do not apply excessive force to the nozzle or subject it to a strong impact. If excessive force is applied to the nozzle or it is subjected to a strong impact, it may become misaligned.



iii.

Handling Guide

1.

Depending on the type of foreign matter attached to the surface of the camera lens, the camera cleaner system may not completely clean the camera lens. If this occurs, wash the camera lens with a large amount of water and wipe the lens with a wet soft cloth.

2.

Do not scrub the camera lens. Scrubbing may scratch the camera lens and affect the image.



iv.

Notice

1.

If washer fluid does not spray out, do not continue to operate the rear washer switch. Doing so may damage the pump.

2.

In order to prevent the washer fluid from freezing, use a washer fluid that is appropriate for the outside air temperature.

3.

Do not allow water to directly contact the nozzle when washing the vehicle with a high pressure washer. The camera may stop operating normally if subject to impact from high pressure water. Also, water may enter the nozzle injection opening and freeze, causing the washer fluid to not spray properly.