FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
| Power Steering Link Assembly | Increases operation force of the steering wheel and transmits operation force to the front wheel. | |
| Vane Pump Assembly | VFC Solenoid Valve | Controls the discharge flow rate and is controlled by the power steering ECU assembly. |
| Vane Pump Oil Reservoir Assembly | Stores the power steering fluid. | |
| Combination Meter Assembly | Power Steering Warning Light | Lights up to alert the driver that the power steering ECU assembly has detected a malfunction in the power steering system. |
| Steering Sensor | Detects the steering direction and the angle of the steering wheel. | |
| Power Steering ECU Assembly | Calculates the optimum discharge flow rate in accordance with the vehicle condition, and controls the VFC solenoid valve. | |
| Brake Actuator Assembly | No. 2 Skid Control ECU | Sends the vehicle speed signal. |
| ECM | Sends the engine speed signal. | |
| 4 Wheel Drive Control ECU | Sends the L4 position condition signal. | |
| Integration Control Assembly | Transfer Position Switch | Switches the drive mode and transmits a signal to the 4 wheel drive control ECU. |
| Integration Control and Panel Sub-assembly | DRIVE MODE Switch | Selects the drive mode. |
| MODE SELECT Switch | Switches the drive mode select. | |
SYSTEM CONTROL
The Variable Flow Control (VFC) power steering optimizes the discharge rate of the power steering fluid sent from the vane pump based on the vehicle speed, steering speed, steering angle and engine speed. There are 3 types of discharge rate control: basic control, L4 range control and drive mode cooperative control.
The basic control includes standby control and assist control. When the steering wheel is not operated such as while driving straight, standby control is performed. The moment the steering wheel is operated, standby control switches to assist control. Also, steering angle correction is performed to gradually reduce the discharge rate based on the vehicle speed and steering angle.
Under standby control, the discharge rate is maintained in order to suppress the drive torque of the vane pump and help improve fuel efficiency.
Under assist control, the discharge rate is increased when the steering wheel is operated at low speeds in order to reduce steering force. On the other hand, the discharge rate is reduced when the steering wheel is operated at high speeds in order to maintain a solid steering force.
Under L4 range control, control characteristics that limit variations in the discharge rate due to changes in steering speed and vehicle speed are used in order to determine the ground conditions between the tires and the road surface during off-road driving.
Optimal discharge rate control is performed depending on the driving mode.
Basic Control
The power steering ECU assembly switches between standby control and assist control depending on the vehicle speed, steering speed and steering angle.
Under assist control, the discharge rate is determined based on the vehicle speed and steering speed.
The discharge rate is then adjusted in response to the steering angle.
| Control | Function | Outline |
|---|---|---|
| Standby Control (Assist Control → Standby Control) |
The steering speed is 0 deg/sec for 0.5 seconds or more when the vehicle speed is 0 km/h. | The discharge rate decreases at a rate of 0.5 l/min per second. (The discharge rate may increase depending on the steering conditions.) |
| The steering angle is less than 4.5° for 0.5 seconds or more except when the vehicle speed is 0 km/h. | The discharge rate decreases at a rate of 5 l/min per second. (The discharge rate may increase depending on the steering conditions.) | |
| Assist Control (Standby Control → Assist Control) |
The steering speed is 0 deg/sec more when the vehicle speed is 0 km/h. | The discharge rate increases according to the steering speed. The rate of increase is determined by the time constant as shown in the following graph. (The discharge rate may decrease depending on the steering conditions. The rate of decrease is determined by the time constant as shown in the following graph.) |
| The steering angle is 4.5° or more except when the vehicle speed is 0 km/h. |
*: The time constant is the amount of time required for the power steering fluid to reach a target discharge rate of 63.2%.
L4 Range Control
In off-road driving, the steering force amount is important information for understanding the condition of the contact between the tires and the road. Accordingly, this system has the control feature of allowing the discharge flow rate to change as little as possible in accordance with the vehicle speed and steering speed when in transfer drive mode L4.
Drive Mode Cooperative Control
By optimizing discharge rate control based on the status of the driving mode, the steering conditions of the vehicle are easily conveyed to the driver, achieving improved steering feel and a sense of unity between the vehicle and driver.