Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM
NM38G0E _54 Brake _102530 PARKING BRAKE _0474232 ELECTRIC PARKING BRAKE SYSTEM CO CONTROL F

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  CONTROL  ELECTRIC PARKING BRAKE CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Models with AC60F automatic transmission

*2: Models with AJA0F automatic transmission

Parking Brake Actuator Assembly Controls the brake pad position by operating the motor according to signals from the No. 2 skid control ECU and locks or releases the parking brake.
Electric Parking Brake Switch Assembly Electric Parking Brake Switch
·

Sends the lock or release operation signal to the No. 2 skid control ECU.

·

Switches the auto function on and off.


Combination Meter Assembly Parking Brake Indicator Light
·

Illuminates to inform the driver that the parking brake has locked.

·

Blinks to inform the driver that the electric parking brake system cannot be operated by driver switch operations.


Brake System Warning Light (Yellow Indicator) Illuminates to inform the driver that the No. 2 skid control ECU detected a malfunction in the electric parking brake system.
Multi-information Display
·

Informs the driver that the No. 2 skid control ECU has a malfunction in the electric parking brake system.

·

Displays the auto function on and off.


Buzzer Sounds together with the indication of the multi-information display in order to inform the driver of a malfunction in the electric parking brake system.
Airbag ECU (Airbag ECU Assembly) Deceleration Sensor Detects the gradient of the road surface by detecting the inclination of the vehicle.
Brake Actuator Assembly No. 2 Skid Control ECU Controls the motor in the parking brake actuator assembly based on information from the electric parking brake switch, the built-in current sensor and each ECU.
ECM Sends the accelerator pedal position signal and shift position signal*1 to the No. 2 skid control ECU.
Transmission Control ECU Assembly*2 Sends the shift position signal to the No. 2 skid control ECU.
Brake Booster with Master Cylinder Assembly No. 1 Skid Control ECU Sends the regulator pressure signal and brake pedal depressed signal to the No. 2 skid control ECU.
Main Body ECU (Multiplex Network Body ECU) Sends the driver side door opening or closing state signal and driver seat belt fasten condition signal to the No. 2 skid control ECU.
Central Gateway ECU (Network Gateway ECU) Relays and transmits each CAN communication data signal.


SYSTEM CONTROL


a.

The No. 2 skid control ECU locks or releases the parking brake by controlling the rotation direction and drive current of the motor built into the parking brake actuator assembly based on signals from the electric parking brake switch and each ECU.


b.

When the electric parking brake is locked, the No. 2 skid control ECU operates the motor in the parking brake actuator assembly to lock the parking brake.


c.

When the electric parking brake is released, the No. 2 skid control ECU reverse operates the motor in the parking brake actuator assembly to release the parking brake.


d.

The No. 2 skid control ECU detects the motor operation condition via its built-in current sensor.


e.

The No. 2 skid control ECU generates braking force according to the road surface while the vehicle is stopped by calculating the road grade based on the signal from the deceleration sensor to control the motor drive current.



FUNCTION


a.

Manual Function

i.

When the electric parking brake switch is pulled with the vehicle stopped, the parking brake locks.


ii.

When the brake pedal is depressed, and then the electric parking brake switch is pushed, the parking brake releases.


iii.

Braking force is only generated while the electric parking brake switch is pulled up when the vehicle is in motion. The braking force is generated by hydraulic pressure, and while the braking force is being generated, the brake light illuminates. When the switch is released, the braking force decreases.


iv.

The parking brake lock operation can be operated regardless of whether the ignition switch is turned on (IG) or off.


v.

The parking brake can be released when the ignition switch is turned on (IG).



b.

Auto Function

i.

The auto function can be switched to on and off via operation of the electric parking brake switch.


ii.

When the electric parking brake switch is pulled and held for 3 seconds or more with the parking brake locked, the auto function turns on. Then a message is displayed on the multi-information display indicating that the auto function is on.

HINT:

When switching from the parking brake released condition, it is necessary to pull it for 5 seconds or more.



iii.

When the electric parking brake switch is pushed and held for 3 seconds or more with the parking brake released, the auto function turns off. Then a message is displayed on the multi-information display indicating that the auto function is off.

HINT:

When switching from the parking brake locked condition, it is necessary to press it for 5 seconds or more.



iv.

When the driver changes the shift position to P while the auto function is on, the parking brake is locked. Also, when the shift position is changed from P to any other position with the brake pedal depressed, the parking brake is released.



c.

Parking Brake Automatic Release Function

i.

When all of the following conditions are met and the driver depresses the accelerator pedal, the parking brake is released.

·

Driver side door is closed.

·

Shift position is not in P or N.

·

Driver side seat belt is fastened.






FAIL-SAFE


a.

When a malfunction occurs in the system, control using the manual function is maintained as much as possible and control using the auto function and parking brake automatic release function is prohibited.

HINT:

When a malfunction occurs in the electric parking brake switch, the system automatically switches to the auto function to ensure operability.



b.

When the parking brake cannot be released due to the fail-safe state or a malfunction in the power source system, the parking brake can be released by supplying power to the electric release connector. For details, refer to the Repair Manual.


c.

When the parking brake cannot be released due to a mechanical malfunction, the parking brake can be released by removing the parking brake actuator assembly from the brake caliper. For details, refer to the Repair Manual.



DIAGNOSIS


a.

If a malfunction is detected in the system, the No. 2 skid control ECU will alert the driver by illuminating the brake system warning light (yellow indicator) in the combination meter and outputting a warning message on the multi-information display.


b.

At the same time, Diagnosis Trouble Codes (DTCs) are stored in the memory. The DTCs stored in the No. 2 skid control ECU are output to the Global TechStream (GTS) connected to the DLC3. For details, refer to the Repair Manual.