FUNCTION OF MAIN COMPONENTS
The main components of the engine control system are as follows:
| Component | Outline | Quantity | Function | |
|---|---|---|---|---|
| ECM | 32-bit CPU | 1 | The ECM performs overall control of the engine control system to suit the operating conditions of the engine in accordance with the signals provided by the sensors. | |
| Mass Air Flow Meter Sub-assembly | Air Flow Meter | Hot-wire Type | 1 | This sensor has a built-in hot-wire to directly detect the intake air mass. |
| Intake Air Temperature Sensor | Thermistor Type | 1 | Detects the intake air temperature. | |
| E.F.I. Engine Coolant Temperature Sensor | Thermistor Type | 1 | Detects the engine coolant temperature by means of an internal thermistor. | |
| Crank Position Sensor [Rotor Teeth] | Pick-up Coil Type [36-2] | 1 | Detects the engine speed and performs cylinder identification. | |
| VVT Sensor (Intake) | Magnetic Resistance Element (MRE) Type [3] | 2 (1 each bank) | These sensors perform the cylinder identification and detect VVT angle. | |
| VVT Sensor (Exhaust) | MRE Type [3] | 2 (1 each bank) | These sensors detect VVT angle. | |
| Accelerator Pedal Position Sensor | Linear (Non-contact) Type | 1 | Detects the amount of pedal effort applied to the accelerator pedal. | |
| Throttle Body with Throttle Position Sensor Assembly | Throttle Control Motor | DC Motor | 1 | Regulates the opening of the throttle valve in accordance with the signals from the ECM. |
| Throttle Position Sensor | Hall IC (Non-contact) Type | 1 | Detects the throttle valve opening angle. | |
| Knock Control Sensor | Built-in Piezoelectric Type (Non-resonant Type/Flat Type) | 2 (1 each bank) | Indirectly detects an occurrence of engine knocking from the resulting vibration of the cylinder block. | |
| Camshaft Timing Oil Control Valve Assembly | Solenoid Type | 4 (2 each bank) | Changes the oil passage to the VVT-i controller in response to signals from the ECM. | |
| Heated Oxygen Sensor | Heated Type (Cup Type) | 2 (1 each bank) | Detects the oxygen concentration in the exhaust emissions by measuring the electromotive force which is generated in the sensor itself. | |
| Air Fuel Ratio Sensor | Heated Type (Planar Type) | 2 (1 each bank) | Detects the oxygen concentration in the exhaust emissions as with the oxygen sensor. However, it detects the oxygen concentration in the exhaust emissions linearly. | |
| Fuel Injector Assembly | 12-hole Type | 6 (3 each bank) | The fuel injector assembly is an electromagnetically-operated nozzle which injects fuel in accordance with signals from the ECM. | |
| Ignition Coil Assembly | Type with Igniter | 6 (3 each bank) | Incorporates an igniter and provides a high level of voltage necessary for ignition in accordance with signals from the ECM. | |
| Spark Plug | Long-reach Type | 6 (3 each bank) | Sparks a high level of voltage from the ignition coil assembly inside the cylinder. | |
SYSTEM CONTROL
The engine control system has the following features. The ECM controls these systems:
| System | Outline |
|---|---|
|
*: Operation may not be possible in certain situations |
|
| Sequential Multiport Fuel Injection (SFI) |
·
An L-type SFI system directly detects the intake air mass with the hot wire type mass air flow meter.
·
The fuel injection system is a sequential multiport fuel injection system.
·
Fuel injection takes 2 forms:
-
Synchronous injection, which always takes place with the same timing in accordance with the basic injection duration and additional correction based on signals provided by the sensors.
-
Non-synchronous injection, which takes place at the time of an injection request based on signals provided by the sensors is detected, regardless of the crankshaft position.
·
Synchronous injection is further divided into group injection during a cold start, and independent injection after the engine is started. |
| Electronic Spark Advance (ESA) |
·
Ignition timing is determined by the ECM based on signals from various sensors. The ECM corrects ignition timing in response to engine knocking.
·
This system selects the optimal ignition timing in accordance with signals received from the sensors and sends ignition signals (IGT) to the igniters. |
| Electronic Throttle Control System-intelligent (ETCS-i) | Optimally controls the throttle valve opening in accordance with the amount of accelerator pedal effort and the condition of the engine and the vehicle. |
| Dual Variable Valve Timing-intelligent (VVT-i) | Regulates operation of the intake and exhaust camshafts to ensure an optimal valve timing in accordance with the engine conditions. |
| Fuel Pump Control |
·
Based on signals from the ECM, the fuel pump controll ECU contrlos the fuel pump.
·
The fuel pump is stopped when the Supplemental Restraint System (SRS) airbags are deployed. |
| Air Conditioning Cut-off Control | By turning the air conditioning compressor assembly on or off in accordance with the engine condition, driveability is maintained. |
| Air Fuel Ratio Sensor and Oxygen Sensor Heater Control | Maintains the temperature of the air fuel ratio sensors or oxygen sensors at an appropriate level to increase the detection accuracy of the exhaust gas oxygen concentration. |
| Drive Start Control | If an abnormal shift (R to D/S, D/S to R, N to R, P to D/S, P to R*) is detected while accelerating, a warning is displayed in the combination meter assembly and engine output is reduced to limit the acceleration, help avoid the collision or help reduce the impact of the collision. |
| Brake Override System | The engine output is restricted when both the accelerator and brake pedals are depressed. (For the Activation Conditions and Inspection method, refer to the Repair Manual.) |
| Engine Immobiliser | Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid key. |
FAIL-SAFE
When the ECM detects a malfunction, the ECM stops or controls the engine in accordance with the data already stored in memory.
DIAGNOSIS
When the ECM detects a malfunction, the ECM diagnoses and memorizes the failed section.