Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
NM38G0E _51 Engine / Hybrid System _102382 1GR-FE ENGINE CONTROL _0476999 SFI SYSTEM DE DETAILS F

1GR-FE ENGINE CONTROL  SFI SYSTEM  DETAILS  KNOCK CONTROL SENSOR  


CONSTRUCTION


a.

In a conventional knock control sensor (resonant type), a vibration plate is built into the sensor. This plate has the same resonance point as the knocking* frequency of the cylinder block sub-assembly. This sensor can only detect vibrations in this frequency band.

*: The terms "knock" or "knocking" are used in this case to describe either preignition or detonation of the air fuel mixture in the combustion chamber. Preignition or detonation refers to the air fuel mixture being ignited earlier than is advantageous. This use of "knock" or "knocking" is not primarily used to refer to a loud mechanical noise that may be produced by an engine.


b.

A flat type knock control sensor (non-resonant type) has the ability to detect vibrations in a wider frequency band (from about 6 to 15 kHz) and has the following features:

·

A flat type knock control sensor is installed to an engine by placing it over a stud bolt installed on the cylinder block sub-assembly. For this reason, a hole for the stud bolt exists in the center of the sensor.

·

In the sensor, a steel weight is located in the upper portion. An insulator is located between the weight and a piezoelectric element.

·

An open/short circuit detection resistor is integrated into the sensor.


W128427C01
1.188,1.354 0.708,1.01 true 1.167,1.458 0.667,1.281 true 1.146,1.542 0.781,1.74 true 2.385,1.51 2.438,0.781 true 5.448,1.292 6.146,0.885 true 5.5,1.333 6.219,1.531 true 0.625,0.396 0.927,0.667 0.302,0.271 12 false *A: 4.271,0.375 4.573,0.646 0.302,0.271 12 false *B: 0.604,1.688 0.865,1.927 0.26,0.24 11 false *3 0.49,1.156 0.75,1.396 0.26,0.24 11 false *2 0.531,0.875 0.792,1.115 0.26,0.24 11 false *1 2.375,0.604 2.635,0.844 0.26,0.24 11 false *4 6.177,0.76 6.438,1 0.26,0.24 11 false *3 6.25,1.479 6.51,1.719 0.26,0.24 11 false *5
*A Flat Type (Non-resonant Type) *B Conventional Type (Resonant Type)
*1 Steel Weight *2 Insulator
*3 Piezoelectric Element *4 Open/Short Circuit Detection Resistor
*5 Vibration Plate - -



c.

The engine knocking frequency will vary slightly depending on the engine speed. The flat type knock control sensor can detect vibrations even when the engine knocking frequency changes. Due to the use of the flat type knock control sensor, the vibration detection ability is increased compared to a conventional type knock control sensor, and more precise ignition timing control is possible.

W100047E18
3.865,1.375 3.74,1.375 3.74,1.375 3.594,1.615 false 5.49,2.208 5.229,2.208 5.229,2.208 5.115,2.094 false 4,0.813 6.156,1 2.156,0.188 10 Detection Band of Resonant Type 3.76,1.625 5.573,1.813 1.813,0.188 10 Detection Band of Flat Type 3.177,2.375 3.958,2.563 0.781,0.188 10 Frequency 1.167,1.281 1.74,1.438 0.573,0.156 10 Voltage 1.563,0.292 1.802,0.479 0.24,0.188 10 (V) 5.083,2.323 5.406,2.51 0.323,0.188 10 (Hz) 3.917,1.292 4.104,1.479 0.188,0.188 10 *1 5.531,2.125 5.719,2.313 0.188,0.188 10 *2 0.219,3.031 4.125,3.24 3.906,0.208 10 *1: Resonance Characteristic of Conventional Type (Resonant) 0.229,3.302 3.885,3.51 3.656,0.208 10 *2: Resonance Characteristic of Flat Type (Non-resonant)


d.

An open or short circuit detection resistor is integrated in the sensor. When the ignition switch is ON, the open circuit detection resistor in the knock control sensor and the resistor in the ECM keep the voltage at terminal KNK1 constant. An Integrated Circuit (IC) in the ECM constantly monitors the voltage of terminal KNK1. If an open or short circuit occurs between the knock control sensor and the ECM, the voltage of terminal KNK1 will change and the ECM will detect this and store a Diagnostic Trouble Code (DTC).

W128429E06
1.875,0.281 1.708,0.281 1.708,0.281 1.208,2.271 true 1.906,2.219 2.333,0.656 2.333,0.656 2.49,0.656 true 1.938,0.198 3.333,0.542 1.396,0.344 10 false Piezoelectric Element 1.031,2.969 2.51,3.25 1.479,0.281 10 false Knock Control Sensor 2.552,0.573 5,0.917 2.448,0.344 10 false Open/Short Circuit Detection Resistor 2,2.219 2.5,2.5 0.5,0.281 10 false 200 kΩ 5.135,1.042 5.542,1.375 0.406,0.333 10 false ECM 4.375,1.146 4.656,1.5 0.281,0.354 10 false 5 V 4.531,1.688 5.042,1.906 0.51,0.219 10 false 200 kΩ 6.073,1.979 6.24,2.313 0.167,0.333 10 false IC 3.75,2.615 4.177,2.802 0.427,0.188 10 false EKNK 3.771,1.781 4.156,1.969 0.385,0.188 10 false KNK1


e.

Vibrations caused by knocking are transmitted to the steel weight. The inertia of this weight applies pressure to the piezoelectric element. This action generates electromotive force.

W104688C18
1.417,1 1.583,1 1.583,1 2.073,1.26 true 1.406,1.958 1.604,1.958 1.604,1.958 2.063,1.573 true 1.417,1.417 2.104,1.417 true 1.219,0.917 1.469,1.125 0.25,0.208 10 false *1 1.219,1.323 1.49,1.542 0.271,0.219 10 false *a 1.198,1.885 1.438,2.094 0.24,0.208 10 false *2
*1 Steel Weight *2 Piezoelectric Element
*a Inertia - -