Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › ENGINE UNIT
NM38G0E _51 Engine / Hybrid System _102383 1GR-FE ENGINE MECHANICAL _0477031 ENGINE UNIT DE DETAILS F

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  DETAILS  CYLINDER BLOCK  


CONSTRUCTION


a.

The cylinder block is made of aluminum alloy.


b.

The cylinder block has a bank angle of 60°, a bank offset of 36.6 mm (1.441 in.) and a bore pitch of 105.5 mm (4.15 in.), resulting in a compact block in its length and width even for its displacement.


c.

Installation bosses of the two knock sensors are located on the inner side of left and right banks.

W133197C01
3.563,0.229 6.719,3.594 3.156,3.365 5.188,1.552 5.865,0.625 5.865,0.625 5.365,1.99 true 3.646,0.292 3.99,0.594 0.344,0.302 10 false *a 1.229,0.646 1.552,0.865 0.323,0.219 10 false *b 5.896,0.448 6.302,0.688 0.406,0.24 10 false *c 4.667,3.104 4.958,3.344 0.292,0.24 10 false *d 5.01,3.281 5.313,3.51 0.302,0.229 10 false *e
*a View from Top Side *b 60°
*c Knock Sensor Boss *d 36.6 mm (1.441 in.)
*e 105.5 mm (4.15 in.) - -



d.

Water passages have been provided between the cylinder bores. By allowing the engine coolant to flow between the cylinder bores, this construction enables the temperature of the cylinder walls to be kept uniform.

W133198C01
5.49,2.01 5.49,3.021 true 5.427,3.063 5.802,3.344 0.375,0.281 10 false *a
*a Water Passage - -



e.

A compact block has been achieved by producing the thin cast-iron liners and cylinder block as a unit. Do not bore the block with this liner.


f.

The liners are the spiny-type, which have been manufactured so that their casting exterior forms a large irregular surface in order to enhance the adhesion between the liners and the aluminum cylinder block. The enhanced adhesion helps improve heat dissipation, resulting in a lower overall temperature and heat deformation of the cylinder bores.


g.

The shape of the cross-hatching of the liner surface has been optimized to improve oil retention performance, resulting in reduced friction.

W133199C01
6.313,2.042 6.771,1.844 true 5.792,1.406 6.104,0.542 6.104,0.542 6.271,0.542 false 5.875,1.906 6.188,1.042 6.188,1.042 6.354,1.042 true 2.542,2.917 2.938,3.458 true 6.354,0.417 6.625,0.667 0.271,0.25 10 false *1 6.417,0.948 6.688,1.177 0.271,0.229 10 false *2 6.813,1.719 7.063,1.958 0.25,0.24 10 false *a 6.01,3.073 6.448,3.406 0.438,0.333 10 false *b 4.615,1.74 4.948,2.01 0.333,0.271 10 false *c 3.563,1.177 3.792,1.469 0.229,0.292 10 false A 2.823,1.375 3.052,1.667 0.229,0.292 10 false A 2.979,3.448 3.25,3.698 0.271,0.25 10 false *1
*1 Cylinder Block *2 Liner
*a Irregularly Shaped Outer Casting Surface of Liner *b A - A Cross Section
*c Enlarged View of Cross-hatching - -



h.

Cylinder block water jacket spacers have been added to the water jacket.


i.

The cylinder block water jacket spacer prevents water flow in the middle and below the water jacket and draws coolant above the cylinder bore, to ensure uniform temperature distribution. As a result, the viscosity of the engine oil that acts as a lubricant between the bore walls and the pistons can be lowered, thus reducing friction.

W133200C01
5.354,1.042 5.542,0.635 5.542,0.635 5.74,0.635 false 2.385,1.927 0.844,1.917 0.844,1.917 1.865,1.573 true 5.365,1.875 5.833,1.885 true 0.625,1.844 1.01,2.146 0.385,0.302 10 false *1 5.802,0.563 6.125,0.76 0.323,0.198 10 false *2 5.135,3.49 5.49,3.708 0.354,0.219 10 false *a 4.365,1.125 4.646,1.5 0.281,0.375 10 false A 3.552,1.26 3.719,1.479 0.167,0.219 10 true A 5.917,1.823 6.302,2.125 0.385,0.302 10 false *1
*1 Cylinder Block Water Jacket Spacer *2 Water Jacket
*a A - A Cross Section - -