OUTLINE
The 1GR-FE engine is a V-type, 6-cylinder, 4.0-liter, 24-valve DOHC engine.
This engine uses the Dual Variable Valve Timing-intelligent (VVT-i) system, Direct Ignition System (DIS), Electronic Throttle Control System-intelligent (ETCS-i), and secondary air injection system*. These control functions achieve improved engine performance, fuel economy, and clean emissions.
*: Models with secondary air injection system
SPECIFICATION
|
*1: Emission regulations differ by country and region. *2: Weight shows the figure with oil and coolant fully filled. |
|||
| No. of Cyls. and Arrangement | 6-cylinder, V-type | ||
| Valve Mechanism | 24-valve DOHC, Chain Drive (with Dual VVT-i) | ||
| Combustion Chamber | Pentroof Type | ||
| Manifolds | Cross-flow | ||
| Fuel System | Sequential Multiport Fuel Injection (SFI) | ||
| Ignition System | Direct Ignition System (DIS) | ||
| Displacement | 3956 cm3 (241.4 cu. in.) | ||
| Bore x Stroke | 94.0 mm x 95.0 mm (3.70 in. x 3.74 in.) | ||
| Compression Ratio | 10.4 : 1 | ||
| Max. Output [NET] | 202 kW @ 5600 rpm | ||
| Max. Torque [NET] | 385 N*m @ 4400 rpm | ||
| Valve Timing | Intake | Open | -11° BTDC to 29° BTDC |
| Closed | 71° ABDC to 31° ABDC | ||
| Exhaust | Open | 60° BBDC to 25° BBDC | |
| Closed | 4° ATDC to 39° ATDC | ||
| Spark Plug | Manufacturer | DENSO | |
| Type | SK16HR11 | ||
| Plug Gap | 1.0 mm to 1.1 mm (0.0394 in. to 0.0433 in.) | ||
| Firing Order | 1 - 2 - 3 - 4 - 5 - 6 | ||
| Research Octane Number | 95 or higher | ||
| Emission Regulation*1 | EURO 2 | ||
| EURO 3 | |||
| EURO 4 | |||
| EURO 5 | |||
| Engine Service Mass (Reference)*2 | 188 kg (435 lb) | ||
MAIN FEATURES
The 1GR-FE engine has achieved the following through the use of the items listed in the table below.
High performance and reliability
Low noise and vibration
Lightweight and compact design
Good serviceability
Clean emissions and fuel economy
| Item | i | ii | iii | iv | v | |
|---|---|---|---|---|---|---|
|
*: Models with secondary air injection system ○: Applicable -: Not applicable |
||||||
| Engine Proper | Upright intake ports are used. | ○ | - | ○ | - | - |
| A taper squish shape is used for the combustion chamber. | ○ | - | - | - | ○ | |
| A steel laminate type cylinder head gasket is used. | ○ | - | - | - | - | |
| A cylinder block sub-assembly made of aluminum alloy is used. | - | - | ○ | - | - | |
| Cylinder block water jacket spacers are used. | ○ | - | - | - | - | |
| The piston skirt is coated with resin. | ○ | ○ | - | - | ○ | |
| An oil pan sub-assembly made of aluminum alloy is used. | - | ○ | ○ | - | - | |
| Valve Mechanism | Timing chains and chain tensioners are used. | ○ | ○ | ○ | - | - |
| Valve lash adjuster assemblies are used. | ○ | ○ | - | ○ | ○ | |
| Valve rocker arm sub-assemblies are used. | ○ | - | - | - | ○ | |
| Lubrication System | An oil filter with a replaceable element is used. | - | - | - | ○ | - |
| Cooling System | TOYOTA Genuine Super Long Life Coolant (SLLC) is used. | - | - | - | ○ | - |
| Intake and Exhaust Systems | A linkless type throttle body with throttle position sensor assembly is used. | - | - | ○ | ○ | - |
| An intake air surge tank assembly made of plastic is used. | - | - | ○ | - | - | |
| Stainless steel exhaust manifold sub-assemblies are used. | - | - | ○ | - | - | |
| Ceramic type Three-Way Catalytic converters (TWCs) are used. | - | - | - | - | ○ | |
| Fuel System | 12-hole type fuel injector assemblies are used to improve the atomization of fuel. | ○ | - | - | - | ○ |
| A fuel delivery pipe sub-assembly that is made of plastic is used. | - | - | ○ | - | - | |
| Ignition System | The Direct Ignition System (DIS) makes ignition timing adjustment unnecessary. | ○ | - | - | ○ | ○ |
| Long-reach type iridium-tipped spark plugs are used. | ○ | - | - | ○ | ○ | |
| Serpentine Belt Drive System | A serpentine belt drive system is used. | - | - | ○ | ○ | - |
| Emission Control System | An evaporative emission control system is used. | - | - | - | - | ○ |
| An secondary air injection system is used.* | - | - | - | - | ○ | |
| Engine Control System | Magneto-Resistance Element (MRE) type VVT sensors are used. | ○ | - | - | - | - |
| The Electronic Throttle Control System-intelligent (ETCS-i) is used. | ○ | - | - | - | ○ | |
| Dual Variable Valve Timing-intelligent (VVT-i) system is used. | ○ | - | - | - | ○ | |