FUNCTION OF MAIN COMPONENTS
The main components in the airbag system have the following functions:
| Components | Function | |
|---|---|---|
|
*1: Models with SRS front side airbag *2: Models with SRS rear side airbag *3: Models with SRS curtain shield airbag *4: Models with rear pretensioner squib |
||
| Driver Airbag (Horn Button Assembly) | Used as supplements to the seat belts to help reduce impact to the occupants. | |
| Front Passenger Airbag (Instrument Panel Passenger without Door Airbag Assembly) | ||
| Driver Knee Airbag (Lower No. 1 Instrument Panel Airbag Assembly) | ||
| Passenger Knee Airbag (Lower No. 2 Instrument Panel Airbag Assembly) | ||
| Driver Side Airbag (Front Seat Airbag Assembly)*1 | ||
| Front Passenger Side Airbag (Front Seat Airbag Assembly)*1 | ||
| Rear Side Airbag (Rear Seat Airbag Assembly)*2 | ||
| Curtain Shield Airbag Assembly LH*3 | ||
| Curtain Shield Airbag Assembly RH*3 | ||
| Front Seat Outer Belt Assembly LH
·
Seat Belt Pretensioner |
Used to help reduce impact to the occupants. | |
| Front Seat Outer Belt Assembly RH
·
Seat Belt Pretensioner |
||
| Rear No. 1 Seat Outer Belt Assembly LH*4
·
Seat Belt Pretensioner |
||
| Rear No. 1 Seat Outer Belt Assembly RH*4
·
Seat Belt Pretensioner |
||
| Spiral Cable Sub-assembly | Transmits ignition signals from the airbag ECU to the SRS driver airbag. | |
| Front Airbag Sensor LH | Based on the deceleration of the vehicle during a frontal collision, distortion is created in the sensor and is converted into an electrical signal. | |
| Front Airbag Sensor RH | ||
| Side Airbag Pressure Sensor LH*3 | Detects deformation of the front doors during a front side collision using the pressure sensor and sends signals for the airbag ECU to determine if deployment of SRS components is necessary. | |
| Side Airbag Pressure Sensor RH*3 | ||
| Floor Side Airbag Sensor LH*3 | Based on the deceleration of the vehicle during a front and rear side collision, distortion is created in the sensor and is converted into an electrical signal. | |
| Floor Side Airbag Sensor RH*3 | ||
| No. 2 Side Airbag Sensor LH*3 | Based on the deceleration of the vehicle during a rear side collision, distortion is created in the sensor and is converted into an electrical signal. | |
| No. 2 Side Airbag Sensor RH*3 | ||
| Rear Floor Side Airbag Sensor*3 | ||
| Airbag ECU (Airbag ECU Assembly) |
·
In the event of a frontal collision, the airbag ECU receives signals from either of the front airbag sensors. The airbag ECU receives the signal via its judgment circuit and also receives another signal from the safing sensor built into the airbag ECU. After receiving a signal from at least one of the front airbag sensors and the safing sensor, the airbag ECU determines whether the SRS driver airbag, SRS front passenger airbag, SRS driver knee airbag and front and rear seat belt pretensioners should be deployed. The airbag ECU also diagnoses system malfunctions.
·
In the event of a side collision, the airbag ECU receives signals from the side airbag pressure sensor, No. 2 side airbag sensor, floor side airbag sensor and rear floor side airbag sensor. The airbag ECU receives the signal via its judgment circuit and also receives another signal from the safing sensor built into the airbag ECU. After receiving a signal from at least one of the side sensors and the safing sensor, the airbag ECU determines whether the SRS front side airbags*1, SRS rear side airbags*2, SRS curtain shield airbags*3, front seat belt pretensioners and rear seat belt pretensioners*4 should be deployed. The airbag ECU also diagnoses system malfunctions. |
|
| Combination Meter Assembly | SRS Warning Indicator | Turns on to alert the driver when the airbag ECU detects a malfunction in the SRS airbag system. |
| Multi-information Display | Displays a warning message to inform the driver of a malfunction in the SRS airbag system. | |
| DLC3 | The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions. | |
OPERATING CONDITION
Frontal Collision
Deceleration sensors used for the SRS airbag system are installed on various parts on the vehicle and calculate the deceleration (or acceleration) rate of each part during a collision.
Depending on the situation, the airbag ECU sends a deployment signal to each SRS airbag based on the information from each sensor.
Frontal collision signals are produced based on the information from the airbag ECU and front airbag sensors. Frontal collision signals are used to deploy the SRS airbags and activate the front seat belt pretensioners and rear seat belt pretensioners*1 as indicated in the table below.
If the severity of the collision is particularly high, the SRS curtain shield airbags LH*2 and SRS curtain shield airbags RH*2 are deployed.
*1: Models with rear pretensioner squib
*2: Models with SRS curtain shield airbag
Side Collision (Front)*
*: Models with SRS Curtain Shield Airbag
The SRS front side airbag, SRS rear side airbag and SRS curtain shield airbag on the front side of the collision is deployed and the front seat belt pretensioner and rear seat belt pretensioner* on the front side of the collision are activated based on signals from the side airbag pressure sensor, floor side airbag sensor and airbag ECU.
If the severity of the collision is particularly high, the SRS curtain shield airbag assembly on the side opposite the collision is deployed and the front seat belt pretensioner and rear seat belt pretensioner* on the side opposite the collision are activated.
*: Models with rear pretensioner squib
During a front side collision, airbags are not deployed based on only signals from the floor side airbag sensor (based on only the safing sensor signal of the floor side airbag sensor and main electronic sensor signal of the floor side airbag sensor).
Side Collision (Rear)*
*: Models with SRS Curtain Shield Airbag
The SRS curtain shield airbag and SRS rear side airbag on the side of the collision is deployed and the rear seat belt pretensioner on the side of the collision is activated based on signals from the No. 2 side airbag sensor, floor side airbag sensor, rear floor side airbag sensor and airbag ECU.
If the severity of the collision is particularly high, the SRS curtain shield airbag on the side opposite the collision is deployed and the rear seat belt pretensioner on the side opposite the collision is activated.
SYSTEM CONTROL
Frontal Collision
SRS airbags which deploy in the event of a frontal collision: the SRS driver airbag, SRS front passenger airbag, SRS driver knee airbag, SRS passenger knee airbag, SRS curtain shield airbag*1. These SRS airbags deploy simultaneously. The SRS front passenger airbag use dual-stage control. In addition, the seat belt pretensioners contained in the front seat outer belt assembly LH, front seat outer belt assembly RH, rear seat outer belt assembly LH*2, rear seat outer belt assembly RH*2 are also activated.
*1: Models with SRS curtain shield airbag
*2: Models with rear pretensioner squib
The airbag ECU detects the information in the table below from various sources in order to activate the dual-stage control.
| Airbag | Information | Source |
|---|---|---|
| Front Passenger | Extent of Impact |
·
Front Airbag Sensor LH or Front Airbag Sensor RH
·
Airbag ECU |
For a frontal collision, if a front airbag sensor detects an impact, it informs the airbag ECU. The airbag ECU causes the SRS driver airbag, SRS front passenger airbag, SRS driver knee airbag, SRS passenger knee airbag to deploy. Additionally, the airbag ECU activates the front seat belt pretensioners and rear seat belt pretensioners.
If the severity of the collision is particularly high, the SRS front and rear curtain shield airbag LH and RH are deployed.
Side Collision (Front)*
*: Models with SRS Curtain Shield Airbag
SRS airbags which deploy in the event of a front side collision: the SRS front side airbag, SRS rear side airbag and SRS curtain shield airbag on the side of the collision. These SRS airbags deploy simultaneously. Additionally, at the same time, the front seat belt pretensioners and rear seat belt pretensioners* on the front side of the collision are also activated.
For a front side collision, if the side airbag pressure sensor and floor side airbag sensor detect an impact, it informs the airbag ECU. The airbag ECU causes the SRS front side airbag, SRS rear side airbag and SRS curtain shield airbag on the front side of the collision to deploy simultaneously, and activates the front seat belt pretensioner and rear seat belt pretensioner* on the front side of the collision.
If the severity of the collision is particularly high, the SRS curtain shield airbag on the side opposite the collision is deployed and the front seat belt pretensioner and rear seat belt pretensioner* on the side opposite the collision are activated.
*: Models with rear pretensioner squib
Side Collision (Rear)*
*: Models with Curtain Shield Airbag
The SRS curtain shield airbag and SRS rear side airbag on the side of the collision in the event of a rear side collision. Additionally, at the same time, the rear seat belt pretensioner* on the rear side of the collision is also activated.
For a rear side collision, if the No. 2 side airbag sensor, floor side airbag sensor and rear floor side airbag sensor detects an impact, it informs the airbag ECU and the airbag ECU causes the SRS curtain shield airbag and SRS rear side airbag on the side of the collision to deploy simultaneously, and activates the rear seat belt pretensioner* on the rear side of the collision.
If the severity of the collision is particularly high, the SRS curtain shield airbag on the side opposite the collision is deployed and the rear seat belt pretensioner* on the side opposite the collision is activated.
*: Models with rear pretensioner squib
Primary Check Illumination Control
After the ignition switch is turned to ON, the airbag ECU illuminates the SRS warning indicator in the combination meter assembly for approximately 6 seconds and conducts the primary check. During the primary check, the ignition of SRS airbags is prohibited and a diagnosis of the airbag ECU is performed. If a malfunction is detected during the primary check, the SRS warning indicator will remain on even after 6 seconds have elapsed.
DIAGNOSIS
If the airbag ECU detects a malfunction in the SRS airbag system, the airbag ECU stores the malfunction data in memory in addition to illuminating the SRS warning indicator.
The airbag ECU outputs malfunction data and Diagnostic Trouble Codes (DTCs) to the Global TechStream (GTS).
The DTCs can be read by connecting the Global TechStream (GTS) to the DLC3. For details, refer to the Repair Manual.
If the SRS airbags deploy, the airbag ECU will turn on the SRS warning indicator. However, unlike an ordinary malfunction, a DTCs will not be stored. The SRS warning indicator cannot be manually turned off. It is necessary to replace the airbag ECU with a new one.