Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
NM38G0E _51 Engine / Hybrid System _101627 V35A-FTS ENGINE CONTROL _0478156 SFI SYSTEM DE DETAILS F

V35A-FTS ENGINE CONTROL  SFI SYSTEM  DETAILS  CAMSHAFT POSITION SENSOR  


CONSTRUCTION


a.

Magneto-Resistance Element (MRE) type cam position sensors are used.


b.

To detect each camshaft position, a timing rotor that is secured to the camshaft is used to generate 3 pulses for every 2 revolutions of the crankshaft. The timing rotor for each camshaft is part of the respective camshaft.

W148508E03
4.229,1.281 4.146,0.958 4.146,0.958 3.927,0.958 true 1.583,3.042 2.458,3.354 true 3.646,3.021 4.865,2.729 true 4.729,3.948 5.302,3.927 true 4.115,4.802 5.156,4.802 true 0.063,0.625 0.667,0.865 0.604,0.24 10 false 180°CA 1.26,0.354 1.865,0.594 0.604,0.24 10 false 120°CA 2.479,0.667 3.083,0.906 0.604,0.24 10 false 120°CA 0.896,2.333 1.5,2.573 0.604,0.24 10 false 60°CA 2.323,1.948 2.927,2.188 0.604,0.24 10 false 180°CA 0.302,1.99 0.906,2.229 0.604,0.24 10 false 60°CA 3.323,0.896 3.927,1.135 0.604,0.24 10 false 120°CA 4.604,0.875 6.031,1.104 1.427,0.229 10 false Timing Rotor (720°CA) 4.927,1.323 5.5,1.563 0.573,0.24 10 false 180°CA 5.615,1.073 6.104,1.271 0.49,0.198 10 true 60°CA 4.417,1.896 5.021,2.135 0.604,0.24 10 false 120°CA 5.344,1.885 5.896,2.073 0.552,0.188 10 true 60°CA 5.969,1.896 6.542,2.135 0.573,0.24 10 false 180°CA 3.417,1.771 3.74,1.99 0.323,0.219 10 false Lo 3.427,1.208 3.635,1.427 0.208,0.219 10 false Hi 4.635,2.156 5.802,2.438 1.167,0.281 10 false Output Waveforms 0.24,2.948 1.552,3.521 1.313,0.573 10 false Cam Position Sensor (Bank 1, Exhaust Side) 4.938,2.646 6.24,3.156 1.302,0.51 10 false Cam Position Sensor (Bank 1, Intake Side) 5.375,3.844 6.677,4.354 1.302,0.51 10 false Cam Position Sensor (Bank 2, Intake Side) 5.24,4.729 6.552,5.302 1.313,0.573 10 false Cam Position Sensor (Bank 2, Exhaust Side)


c.

An MRE type cam position sensor consists of an MRE, a magnet and a sensor. The direction of the magnetic field changes due to the profile (protruding and non-protruding portions) of the timing rotor, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the ECM changes to high or low. The ECM detects the camshaft position based on this output voltage.


d.

The differences between a MRE type sensor and the pick-up coil type sensor used on the conventional models are as follows:

·

The MRE type sensor outputs a constant level of high and low digital signals regardless of the engine speed. Therefore, the MRE type sensor can detect the positions of the camshaft at an early stage of cranking.

·

The pick-up coil type sensor outputs analog signals with levels that change with the engine speed.


MRE Type and Pick-up Coil Type Output Waveform Image Comparison
W126804E01
4.292,3.083 4.292,2.667 true 4.656,1.896 4.656,1.031 4.656,1.031 4.823,1.031 true 0.01,1.125 0.938,1.417 0.927,0.292 10 false Engine Speed 3.01,1.104 3.938,1.396 0.927,0.292 10 false Engine Speed 0,2.74 0.927,3.031 0.927,0.292 10 false Sensor Output 3.021,2.438 3.948,2.729 0.927,0.292 10 false Sensor Output 2.104,3.125 2.99,3.354 0.885,0.229 10 false Digital Output 1.542,3.427 2.302,3.646 0.76,0.219 10 false MRE Type 4.76,3.469 5.729,3.688 0.969,0.219 10 false Pick-up Type 3.917,3.135 5.24,3.354 1.323,0.219 10 false Non Detection Area 6.031,2.708 7,2.948 0.969,0.24 10 false Analog Output 4.896,0.948 6.198,1.188 1.302,0.24 10 false Non Detection Area