OUTLINE
A V6 twin-turbo V35A-FTS (3.5 L) engine is used to achieve a higher dimension of balance between fuel efficiency, high performance, clean exhaust gas performance and quietness.
A Direct injection 4-stroke gasoline engine Superior version (D-4S) system (which uses both a direct cylinder injection method and port injection method) is used to perform efficient combustion. In addition, a turbocharger, Electronic Throttle Control System-intelligent (ETCS-i) and Dual Variable Valve Timing-intelligent (Dual VVT-i) system (a continuously variable valve timing mechanism for intake and exhaust) are used to achieve low fuel consumption, low emissions, high performance and high output.
The Dual Variable Valve Timing-intelligent (Dual VVT-i) system (a continuously variable valve timing mechanism for intake and exhaust) uses a Variable Valve Timing-intelligent (VVT-i) (a continuously variable valve timing mechanism that operates oil pressure) on the intake side and exhaust side to further expand the degree of freedom of control and achieve optimal valve timings.
A Direct injection 4 stroke gasoline engine Superior version with Turbo (D-4ST) that comprehensively performs supercharging control for the turbocharger and Direct injection 4-stroke gasoline engine Superior version (D-4S) system. By optimizing the shape of the cylinder head port and piston top surface, it is possible to achieve high tumble flow in addition to high-level supercharged pressure control, improving fuel efficiency and low speed torque.
The shape of the high-efficient intake port and combustion chamber is optimized to improve combustion efficiency, and the valve mechanism system is improved to reduce friction loss in each part of the engine. As a result, a high level of engine fuel efficiency is achieved.
SPECIFICATION
|
*: Emission regulations differ by country and region. |
|||
| Engine Type | V35A-FTS | ||
| No. of Cyls. & Arrangement | 6-cylinder, V-type | ||
| Valve Mechanism | 24-valve DOHC, Chain Drive (with Dual VVT-i) |
||
| Combustion Chamber | Pentroof Type | ||
| Manifolds | Cross-flow | ||
| Fuel System | Sequential Multiport Fuel Injection (SFI) D-4ST | ||
| Ignition System | Direct Ignition System (DIS) | ||
| Displacement | 3445 cm3 (210.2 cu. in.) | ||
| Bore x Stroke | 85.5 mm x 100.0 mm (3.37 in. x 3.94 in.) | ||
| Compression Ratio | 10.4 : 1 | ||
| Max. Output [NET] | 305 kW @ 5200 rpm | ||
| Max. Torque [NET] | 650 N*m @ 2000 to 3600 rpm | ||
| Valve Timing | Intake | Open | 65° to 0° BTDC |
| Closed | 5° to 70° ABDC | ||
| Exhaust | Open | 60° to 16° BBDC | |
| Closed | 0° to 44° ATDC | ||
| Spark Plug | Manufacturer | DENSO | |
| Type | EC22HPR-D7 (Iridium) | ||
| Plug Gap | 0.6 mm to 0.7 mm (0.0236 in. to 0.0276 in.) | ||
| Firing Order | 1 - 2 - 3 - 4 - 5 - 6 | ||
| Research Octane Number | 95 or higher | ||
| Emission Regulations* | EURO 2 | ||
| EURO 3 | |||
| EURO 4 | |||
| EURO 5 | |||
MAIN FEATURES
The V35A-FTS engine has achieved the following through the use of the items listed below:
(1) High performance and reliability
(2) Low noise and vibration
(3) Lightweight and compact design
(4) Good serviceability
(5) Clean emissions and fuel economy
| Item | (1) | (2) | (3) | (4) | (5) | |
|---|---|---|---|---|---|---|
|
○: Applicable -: Not applicable |
||||||
| Engine Proper | Steel laminate type cylinder head gaskets are used. | ○ | - | - | - | - |
| Spiny-type liners are used in the cylinder bores. | ○ | - | - | - | - | |
| A cylinder head sub-assembly with integrated exhaust manifold is used. | ○ | - | - | - | ○ | |
| Laser cladded valve seats are used for the intake side. | ○ | - | - | - | ○ | |
| The skirt portion of the piston has a resin coating applied to reduce friction. | ○ | ○ | - | - | ○ | |
| A No. 1 oil pan sub-assembly made of aluminum alloy is used. | - | ○ | ○ | - | - | |
| Hydraulic engine mountings (Front Engine Mounting Insulator) are used. | - | ○ | ○ | - | - | |
| Bolts with smaller heads than standard bolts of the same thread diameter are used. | ○ | - | ○ | - | - | |
| Valve Mechanism | Timing chains and chain tensioners are used. | ○ | ○ | ○ | - | - |
| No. 1 valve rocker arm sub-assemblies are used. | ○ | - | - | - | ○ | |
| Valve lash adjuster assemblies are used. | ○ | ○ | - | ○ | ○ | |
| The Dual Variable Valve Timing-intelligent (Dual VVT-i) system is used for the intake and exhaust camshafts. | ○ | - | - | - | ○ | |
| Lubrication System | An engine oil level sensor is used. | - | - | - | - | ○ |
| A cartridge-type oil filter sub-assembly is used. | - | - | - | ○ | - | |
| Cooling System | Toyota Genuine Super Long-Life Coolant (SLLC) is used. | - | - | - | ○ | - |
| Water Control Valve is used. | ○ | - | - | - | ○ | |
| Intake and Exhaust Systems | A throttle body with motor assembly is used. | - | - | ○ | ○ | - |
| Turbocharger sub-assemblies are used. | ○ | ○ | ○ | ○ | - | |
| The wastegate valve control is used. | ○ | - | - | - | ○ | |
| The air bypass valve control is used. | - | ○ | - | - | - | |
| A water cooled type intercooler assembly is used. | ○ | - | ○ | - | ○ | |
| Ceramic type Three-Way Catalytic converters (TWCs) are used. | - | - | - | - | ○ | |
| Fuel System | A Direct injection 4-stroke gasoline engine Superior version with Turbo (D-4ST) system is used. | ○ | - | - | - | ○ |
| Ignition System | A Direct Ignition System (DIS) is used. | ○ | - | ○ | ○ | ○ |
| Long-reach type iridium-tipped spark plugs are used. | ○ | - | - | ○ | ○ | |
| Engine Control System | A Magnetic-Resistance Element (MRE) type crank position sensor and cam position sensors are used. | ○ | - | - | - | ○ |
| An Electronic Throttle Control System-intelligent (ETCS-i) is used. | ○ | - | - | - | ○ | |
| The Dual Variable Valve Timing-intelligent (Dual VVT-i) system is used. | ○ | - | - | - | ○ | |
Location of small-head bolts