FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
|
*1: Models with RSA system *2: Except models with 1GR-FE engine *3: Models with 1GR-FE engine *4: Models with headup display |
||
| Forward Recognition Camera |
·
Detects lane markers and objects on the road ahead using the image captured by the camera sensor.
·
While the system is in vehicle-to-vehicle distance control mode, the forward recognition camera detects the vehicle ahead based on signals from the millimeter wave radar sensor assembly and forward recognition camera. Then, the forward recognition camera calculates the acceleration or deceleration rate required in order to attain the target vehicle-to-vehicle distance, and outputs a request signal to the ECM.
·
Controls the supply of electric current to the camera heater when the ambient temperature is low.
·
If the detects a malfunction in the dynamic radar cruise control system, it will store Diagnostic Trouble Codes (DTCs). |
|
| Camera Heater (Forward Recognition Hood with Heater Sub-assembly) | Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up. | |
| Millimeter Wave Radar Sensor Assembly | Radiates millimeter radar waves forward, uses the reflected waves to detect the presence of a vehicle traveling ahead, the vehicle-to-vehicle distance, and the relative speed, and then sends this information to the forward recognition camera. | |
| Steering Pad Switch Assembly | Cruise Control Main Switch |
·
Turns the dynamic radar cruise control system on and off.
·
Vehicle-to-vehicle distance control mode becomes be activated immediately after the switch is turned on.
·
The mode shifts to constant speed control mode by pushing and holding the switch more than 1.5 seconds while the dynamic radar cruise control system is turned off. |
| CANCEL Switch | Outputs a cancel signal to the ECM when this switch is operated. | |
| +RES Switch |
·
Output the accelerate function and resuming of a preset speed signals to the ECM when this switch is operated.
·
The dynamic radar cruise control with road sign assist operation signals are sent to the ECM.*1 |
|
| -SET Switch |
·
Output the decelerate function and vehicle speed setting signals to the ECM when this switch is operated.
·
The dynamic radar cruise control with road sign assist operation signals are sent to the ECM.*1 |
|
| Vehicle-to-vehicle Distance Control Switch | While the system is in vehicle-to-vehicle distance control mode, the driver can operate the vehicle-to-vehicle distance control switch to select the vehicle-to-vehicle distance in 3 levels: long, middle and short. | |
| Stop Light Switch Assembly | Detects brake pedal depression and transmits its signal to the ECM. | |
| Park/Neutral Position Switch Assembly | Detects the shift lever position and transmits signals to the ECM. | |
| Transmission Control Switch |
·
Detects the shift lever position and transmits signals to the ECM.
·
Informs the ECM of driver upshift or downshift operations while the shift lever is in M*2 or S*3. |
|
| VSC OFF Switch | Outputs a VSC OFF or TRC OFF signal to the No. 2 skid control ECU when this switch is operated. | |
| Electric Parking Brake Switch Assembly
·
Electric Parking Brake Switch |
Sends a parking brake application signal to the No. 2 skid control ECU. | |
| Headlight Dimmer Switch Assembly
·
Turn Signal Switch |
Sends a turn signal command to the steering sensor. | |
| Front Seat Inner Belt Assembly (LH) | Detects if the driver seat belt is fastened. | |
| Front Door Courtesy Light Switch Assembly (LH) | Detects whether the door is open or closed. | |
| Accelerator Pedal Sensor Assembly | Detects the accelerator pedal depression angle and transmits it to the ECM. | |
| Throttle Body with Motor Assembly | Throttle Control Motor | Adjusts the throttle valve opening angle in accordance with signals from the ECM. |
| Throttle Position Sensor | Detects the throttle valve opening angle and outputs it to the ECM. | |
| Steering Sensor |
·
Detects the angle and direction of steering and sends signals to the ECM.
·
Sends a turn signal command to the ECM. |
|
| Airbag ECU (Airbag Sensor with ECU Assembly)
·
Yawrate Sensor |
Detects the yaw rate of the vehicle and sends signals to the No. 2 skid control ECU. | |
| Combination Meter Assembly | Cruise Control Indicator (Constant Speed Control Mode) |
·
Illuminates when the dynamic radar cruise control system in constant speed control mode has been turned on using the cruise control main switch.
·
Turns off if a malfunction occurs in the dynamic radar cruise control system. |
| Cruise Control Indicator (Vehicle-to-vehicle Distance Control Mode) |
·
Illuminates when the dynamic radar cruise control system in vehicle-to-vehicle distance control mode has been turned on using the cruise control main switch.
·
Turns off if a malfunction occurs in the dynamic radar cruise control system. |
|
| Cruise SET Indicator | Illuminates when the vehicle speed is set. | |
| Multi-information Display |
·
Displays a warning message to alert the driver in accordance with a signal provided by the ECM.
·
Displays the system conditions in accordance with a signal provided by the ECM during cruise control operation. |
|
| Buzzer |
·
Sounds a buzzer when it receives a signal from the ECM to alert the driver that the distance between vehicles is short.
·
Sounds to inform the driver if the ECM detects automatic cancel or warning signals while the vehicle is operating under cruise control. |
|
| Headup Display (Meter Mirror Sub-assembly)*4 | Displays the system conditions in accordance with a signal provided by the ECM during cruise control operation. | |
| ECM |
·
Controls the dynamic radar cruise control system in accordance with the signals from switches, sensors and ECUs.
·
If the ECM detects a malfunction in the dynamic radar cruise control system, it will store Diagnostic Trouble Codes (DTCs). |
|
| Transmission Control ECU*2 | Sends the shift position signal to the ECM. | |
| No. 2 Skid Control ECU |
·
Controls the brake actuator in accordance with the brake request signal received from the ECM while the system is operating in vehicle-to-vehicle distance control mode.
·
Transmits the wheel speed signal to the ECM.
·
Transmits the VSC operation signal to the ECM. |
|
| Main Body ECU (Multiplex Network Body ECU) | Transmits the door courtesy light switch signal to the ECM. | |
| Clearance Warning ECU Assembly | Controls the parking support brake system in accordance with the signals from switches, sensors and ECUs. | |
| Central Gateway ECU (Network Gateway ECU) | Transmits the signal between the CAN communication buses. | |
| DLC3 | The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions. | |
FUNCTION
The control of the dynamic radar cruise control system varies depending on the mode:
Constant Speed Control Mode
The ECM compares the set speed and the actual vehicle speed, and performs constant speed control in order to attain the set speed.
Vehicle-to-vehicle Distance Control Mode
In vehicle-to-vehicle distance control mode, the ECM performs constant speed control, deceleration cruising control, follow-up cruising control, acceleration cruising control, stop control*, stop retention control*, start off control*, turn signal-linked control based on the information about the vehicle ahead transmitted from the millimeter wave radar sensor assembly and forward recognition camera.
*: Models with full-speed range following function
The dynamic radar cruise control system has the following control functions:
Mode A: Constant Speed Control Mode
Mode B: Vehicle-to-vehicle Distance Control Mode (without Full-speed Range Following Function)
Mode C: Vehicle-to-vehicle Distance Control Mode (with Full-speed Range Following Function)
| Function | Outline | Mode | ||
|---|---|---|---|---|
| A | B | C | ||
|
*: Models with RSA system ○: Available -: Not available |
||||
| Mode Switching Control | The following operations switch modes:
·
Vehicle-to-vehicle distance control mode is activated immediately after the cruise control main switch is turned on. |
- | ○ | ○ |
| The following operations switch modes:
·
The mode is changed to constant speed control mode by pushing and holding the cruise control main switch for more than 1.5 seconds while the dynamic radar cruise control system is turned off. |
○ | - | - | |
| Constant Speed Control | The ECM compares the actual vehicle speed and the set speed and if the vehicle speed is lower than the set speed, the ECM calculates the optimal motive forces, and accelerates by adjusting the respective motive forces. | ○ | ○ | ○ |
| Set Control | When this system fulfills the following conditions, and the -SET switch is pushed and released, the ECM stores the vehicle speed and maintains the vehicle constantly at that speed.
·
The dynamic radar cruise control system has been turned on using the cruise control main switch.
·
The vehicle is being driven at a speed of approximately 30 km/h (20 mph) or more. |
○ | ○ | ○ |
| When this system fulfills the following conditions, and the -SET switch is pushed and released, the ECM stores the low speed limit [approximately 30 km/h (20 mph)] and maintains the vehicle constantly at that speed.
·
The dynamic radar cruise control system has been turned on using the cruise control main switch.
·
The vehicle is being driven at a speed of approximately 30 km/h (20 mph) or less. |
- | ○ | ○ | |
| Low Speed Limit Control | If the vehicle speed drops below approximately 30 km/h (20 mph) while the cruise control is operating, cruise control will be canceled automatically. However, the set speed is kept in memory. | ○ | ○ | - |
| Coast Control | While the -SET switch is pushed continuously, the vehicle speed and the set speed change as follows:
·
The vehicle decelerates constantly.
·
The set speed changes to the speed at which the -SET switch is released. |
○ | - | - |
| While the -SET switch is pushed continuously, the vehicle speed and the set speed change as follows:
·
The set speed decreases in increments of 5 km/h or 5 mph. [Example: 103 →100 → 95 → 90 → 85 km/h (mph)]
·
The vehicle decelerates rapidly. The vehicle will remain at the speed that the vehicle is traveling at when the -SET switch is released. |
- | ○ | ○ | |
| Tap Down Control | When the -SET switch is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set speed change as follows:
·
The vehicle will decelerate in increments of approximately 1 km/h or 1 mph each time the -SET switch is operated.
·
However, if the difference between the actual vehicle speed and the set speed is greater than 5 km/h (3 mph), the set speed will change to the speed at which the vehicle is being driven at the time the -SET switch is operated. |
○ | - | - |
| When the -SET switch is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set speed change as follows
·
The vehicle will decelerate in increments of approximately 1 km/h or 1 mph for each time the -SET switch is operated. |
- | ○ | ○ | |
| Accelerator Control | While the +RES switch is pushed continuously, the vehicle speed and the set speed change as follows:
·
The vehicle will accelerate constantly.
·
The set speed changes to the speed at which the +RES switch is released. |
○ | - | - |
| While the +RES switch is pushed continuously, the vehicle speed and the set speed change as follows:
·
The set speed increases in increments of 5 km/h or 5 mph. [Example: 83 → 85 → 90 → 95 → 100 km/h (mph)]
·
The vehicle will accelerate to the speed that is set at the time the +RES switch is released. However, only the set speed will change during follow-up cruising control. |
- | ○ | ○ | |
| If the -SET switch is pushed momentarily (approximately 0.6 seconds or less) when the vehicle speed is increased by depressing the accelerator pedal, the system will memorize the set speed at that speed. | ○ | ○ | ○ | |
| Tap Up Control | When the +RES switch is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set speed change as follows:
·
The vehicle will accelerate in increments of approximately 1 km/h or 1 mph for each time the +RES switch was operated.
·
However, if the difference between the actual vehicle speed and the set speed is greater than 5 km/h (3 mph), the set speed will not change. |
○ | - | - |
| When the +RES switch is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set speed change as follows:
·
The vehicle will accelerate in increments of approximately 1 km/h or 1 mph for each time the +RES switch is operated. |
- | ○ | ○ | |
| Resume Control | If the vehicle speed is above approximately 30 km/h (20 mph) or more, the +RES switch can be pushed to resume cruise control operation and reach the vehicle speed that was set at the time the driver canceled cruise control. | ○ | ○ | ○ |
| If the vehicle ahead changes driving lanes during follow-up cruising control, the vehicle speed is gradually increased to the set speed. | - | ○ | ○ | |
| After the vehicle ahead has started running again under stop retention control and then the message that urges the driver to perform the start-off operation has been displayed, when the +RES switch is pushed, follow-up cruising control is resumed and the vehicle can be accelerated up to the set speed. | - | ○ | ○ | |
| Deceleration Cruising Control | Performs motive force control and brake control in order to decelerate the vehicle so that the vehicle-to-vehicle distance between the driver's own vehicle and the vehicle ahead is maintained at the set distance. | - | ○ | ○ |
| Follow-up Cruising Control | After performing deceleration control, the driver's own vehicle follows the vehicle ahead in order to maintain the proper vehicle-to-vehicle distance. The actual distance maintained for each distance level (long, medium and short) varies in accordance with the vehicle speed. | - | ○ | ○ |
| Acceleration Cruising Control | Accelerates the vehicle in order to attain the set speed if the vehicle ahead or the driver's own vehicle has changed lanes. | - | ○ | ○ |
| Shift-down Control | When the vehicle is traveling uphill using cruise control, automatic transmission control may cause the transmission to shift down. During shift down control, when the end of uphill travel is determined based on the throttle valve angle, the transmission will shift up after a certain period of time. When the transmission shifts down during accelerator control or resume control, the transmission will shift up after accelerator control or resume control ends. | ○ | ○ | ○ |
| Turn signal-linked Control | If the turn signal switch is operated when changing lanes to the passing lane at a vehicle speed of approximately 80 km/h (50 mph) during follow-up cruising control, the vehicle will begin preliminary acceleration; once the vehicle has changed lanes it will first maintain this preliminary acceleration, and then slowly accelerate to the set speed. | - | ○ | ○ |
| Excessive Speed Warning | If the vehicle has exceeded the set vehicle speed in the following conditions, the display of the set vehicle speed is inverted.
·
When the accelerator pedal is depressed and the vehicle is being accelerated.
·
When driving on a downhill slope |
- | ○ | ○ |
| Curve Speed Reduction Control | When the system determines that it is necessary to restrain the vehicle speed due to a curve, the system uses motive force control and brake control to perform speed restraint. | - | ○ | ○ |
| Dynamic Radar Cruise Control with Road Sign Assist* | This function is turned on and while RSA system speed limit information is displayed, the speed limit can be set by holding down the +RES switch to increase the set vehicle speed to the speed limit, or by holding down the -SET switch to reduce the set vehicle speed to the speed limit. | - | ○ | ○ |
| Stop Control | Detects if the vehicle ahead has stopped, performs motive force control and brake control and stops the vehicle while maintaining proper vehicle-to-vehicle distance. | - | - | ○ |
| Stop Retention Control | Judges if the vehicle is stopped, performs brake control and keeps the vehicle stopped through the brake hold function. | - | - | ○ |
| Start Off Control | Detects that the vehicle ahead starts moving again under stop retention control, displays the message on the multi-information display to urge the driver to perform the start-off operation (to operate the +RES switch or depress the accelerator pedal), and resumes follow-up cruising control after the vehicle is started off. | - | - | ○ |
| Manual Cancel Control | If any of the following signals are sent to the ECM, the cruise control is canceled accordingly:
·
Brake pedal depression signal other than under stop retention control
·
Shift position D off signal (shift position changed from D to any other position.)
·
Cruise control main switch off signal (Cruise control main switch is pushed.)
·
CANCEL switch on signal (CANCEL switch is pushed.)
·
Parking brake on signal (parking brake is applied.) |
○ | ○ | ○ |
| Automatic Cancel Control | When an automatic cancel signal is sent to the ECM, cruise control operation is canceled. At this time, the type of warning sent to the driver and the control resumption condition varies according to the cancel signal. | ○ | ○ | ○ |
| Other Cancel Conditions |
·
Ignition switch is turned off.
·
VSC is activated.
·
TRC is activated for a certain period of time.
·
TRC or VSC is turned off.
·
Pre-collision system is activated. |
○ | ○ | ○ |
|
·
Drive start control is activated.
·
Parking support brake system is activated. |
- | ○ | ○ | |
SYSTEM CONTROL
Constant Speed Control
The ECM compares the set speed and the actual vehicle speed, and performs constant speed control by regulating the respective motive forces in order to attain the set speed. The forward recognition camera uses the millimeter wave radar sensor assembly signal and information from the forward recognition camera to determine the condition in front of the vehicle and sends acceleration/deceleration requests to the ECM.
Deceleration Cruising Control
The forward recognition camera calculates the target deceleration rate in accordance with signals from the millimeter wave radar sensor assembly, forward recognition camera and transmits a deceleration request signal to the ECM. Upon receiving this signal, the ECM closes the throttle valve in order to cause the vehicle to decelerate.
This control is not performed in the presence of a parked vehicle or object or below the settable vehicle speed range.
If the forward recognition camera determines that further deceleration is necessary, it transmits a brake request signal to the ECM. Upon receiving this signal, the ECM transmits a brake request signal to the No. 2 skid control ECU. The No. 2 skid control ECU then controls the brake actuator to apply the brakes.
At this time, if the deceleration rate is higher than a predetermined value, the No. 2 skid control ECU outputs a stop light illumination request signal to the stop lights in order to warn any vehicles behind.
If the vehicle is not decelerating adequately, the ECM sounds a buzzer. The buzzer is sounded to urge the driver to depress the brake pedal.
Follow-up Cruising Control
After performing deceleration control, the forward recognition camera transmits request signals to the ECM so that the vehicle can follow the vehicle ahead while maintaining the proper vehicle-to-vehicle distance according to the vehicle speed. Upon receiving these signals, these ECM controls the motive force in order to perform follow-up cruising control.
3 stages (long, middle and short) of vehicle-to-vehicle distance can be selected by operating the vehicle-to-vehicle distance control switch.
Acceleration Cruising Control
If the forward recognition camera detects (based on the millimeter wave radar sensor assembly and forward recognition camera) that either the vehicle ahead or the driver has changed lanes, an acceleration request signal is transmitted to the ECM in order to attain the set speed. Upon receiving this signal, the ECM controls the motive force in order to perform acceleration control.
Turn signal-linked Control
If the turn signal switch is operated when changing lanes to the passing lane during follow-up cruising control, the vehicle will begin preliminary acceleration; once the vehicle has changed lanes it will first maintain this preliminary acceleration, and then slowly accelerate to the set speed.
Excessive Speed Warning
If the vehicle has exceeded the set vehicle speed in the following conditions, the display of the set vehicle speed is inverted.
When the accelerator pedal is depressed and the vehicle is being accelerated
When driving on a downhill slope
Curve Speed Reduction Control
When the system determines that it is necessary to restrain the vehicle speed according to information from the sensors while driving in vehicle-to-vehicle distance control mode, displays on the headup display* and multi-information display are used to inform the driver that the curve speed reduction control function is operating.
*: Models with headup display
When control performed by the curve speed reduction control function completes, the display turns off and the vehicle returns to the set speed of the radar cruise control system according to the conditions.
Dynamic Radar Cruise Control with Road Sign Assist (Models with RSA System)
This function is turned on and while RSA system speed limit information is displayed, the speed limit can be set by holding down the +RES switch to increase the set vehicle speed to the speed limit, or by holding down the -SET switch to reduce the set vehicle speed to the speed limit.
Stop Control (Models with Full-speed Range Following Function)
During vehicle-to-vehicle distance control mode, if the vehicle ahead stops, the forward recognition camera maintains an appropriate vehicle-to-vehicle distance while at the same time calculating the necessary motive force to stop the vehicle, and sends a drive request signal to the ECM and No. 2 skid control ECU. When the ECM and No. 2 skid control ECU receive this signal, they control the motive force and brake force and stop the vehicle.
At this time, the No. 2 skid control ECU outputs a stop light illumination request signal in order to inform anyone who might be following the vehicle.
The distance between the driver's own vehicle and the preceding vehicle when the vehicles are stopped is set to approximately 3 m to 5 m (10 ft. to 16 ft.) regardless of the vehicle-to-vehicle distance preset by using the distance control switch.
Stop Retention Control (Models with Full-speed Range Following Function)
After the vehicle has stopped under stop control, ECM transmits a stop retention request signal to the No. 2 skid control ECU. Upon receiving this signal, the No. 2 skid control ECU activates the brake hold function and keeps the vehicle stopped.
If the vehicle ahead starts off within approximately 3 seconds after own vehicle stops, follow-up cruising will be resumed.
Start Off Control (Models with Full-speed Range Following Function)
When the forward recognition camera detects that the vehicle ahead starts moving again from the millimeter wave radar sensor assembly and forward recognition camera signal, it displays the messages on the multi-information display to urge the driver to perform the start-off operation (to push the +RES switch or depress the accelerator pedal).
Upon receiving the start-off operation signal generated by pushing the +RES switch or by depressing the accelerator pedal, the forward recognition camera transmits a motive force request signal to the ECM. Upon receiving this signal, the ECM controls the motive force, starts off the vehicle and resumes follow-up cruising control.
Pushing the +RES switch while the vehicle ahead stops will resume follow-up cruising if the vehicle ahead starts off within approximately 3 seconds after the switch is pushed.
Automatic Cancel Control
If one of the conditions listed below occurs while the vehicle is being driven using cruise control, cruise control will be canceled. Then, the following warning item will appear for the driver.
| Situation | Warning | |
|---|---|---|
| Multi-information Display | Buzzer | |
| If the following condition occurs, the ECM clears the set speed and cancels the cruise control.
·
An open or short circuit in the stop light switch assembly The cruise control is disabled until the ignition switch is turned on again. |
Cruise Control Malfunction Visit Your Dealer |
Sounds |
| If the following condition occurs, the ECM clears the set speed and cancels the cruise control.
·
Malfunction in the engine control system. The cruise control is disabled until the ignition switch is turned on again. |
- | - |
| If either of the conditions listed below occurs, the ECM clears the set speed and cancels the cruise control.
·
Stop light switch assembly input signal is abnormal.
·
Cancel circuit malfunction
·
Brake control system malfunction
·
Communication malfunction between the No. 2 skid control ECU and ECM The cruise control is disabled until the ignition switch is turned on again. |
Cruise Control Malfunction Visit Your Dealer |
Sounds |
| If the following condition occurs, the ECM clears the set speed and cancels the cruise control.
·
The vehicle speed drops more than 16 km/h (10 mph) below the set speed. |
- | - |
| If the following condition occurs, the ECM cancels the cruise control while retaining the set speed in its memory.
·
The vehicle speed drops below the low speed limit [approximately 30 km/h (20 mph)]. |
- | - |
| Situation | Warning | |
|---|---|---|
| Multi-information Display | Buzzer | |
|
*1: Models with full-speed range following function *2: Models without full-speed range following function |
||
| If any of the conditions listed below occur, the ECM clears the set speed and cancels the cruise control.
·
Stop light switch assembly input signal is abnormal.
·
Cancel circuit malfunction
·
Brake control system malfunction
·
Communication malfunction between the No. 2 skid control ECU and ECM
·
An open or short circuit in the stop light switch assembly
·
Malfunction in the millimeter wave radar sensor assembly
·
The brake hold function is malfunction.*1
·
Malfunction in the dynamic radar cruise control system other than those given above The cruise control is disabled until the ignition switch is turned on again. |
Cruise Control Malfunction Visit Your Dealer |
Sounds |
| If the following condition occurs, the ECM cancels the cruise control while retaining the set speed in its memory.
·
The millimeter wave radar sensor assembly or the radar sensor cover are dirty. The cruise control is prohibited until the condition is corrected or the cruise control is turned off and back on again using the cruise control main switch. |
Radar Cruise Control Unavailable See Owner's Manual |
Sounds |
| If any of the following conditions occur, the ECM cancels the cruise control while retaining the set speed in its memory.
·
The measurement becomes extremely unstable due to poor weather conditions.
·
Brake control by the dynamic radar cruise control system is temporarily unavailable.
·
Misalignment of the axis of the millimeter wave radar sensor assembly
·
A Malfunction in the forward recognition camera
·
Forward recognition camera temporarily not available The cruise control is prohibited until the condition is corrected or the cruise control is turned off and back on again using the cruise control main switch. |
Radar Cruise Control Unavailable |
Sounds |
| If the following condition occurs, the ECM cancels the cruise control while retaining the set speed in its memory.*2
·
The vehicle speed drops below the low speed limit [approximately 25 km/h (16 mph)]. |
- | - |
| If any of the following conditions occur while the vehicle stopped, the ECM cancels the cruise control.*1
·
An open or short circuit in the stop light switch assembly
·
Malfunction in the millimeter wave radar sensor assembly
·
The brake hold function is malfunction. The cruise control is disabled until the ignition switch is turned on again. |
Cruise Control Fault Press Brake to Deactivate Visit Your Dealer |
Sounds |
| If any of the following conditions occur while the vehicle stopped, the ECM cancels the cruise control while retaining the set speed in its memory.*1
·
The millimeter wave radar sensor assembly or the radar sensor cover are dirty.
·
The measurement becomes extremely unstable due to poor weather conditions.
·
Brake control by the dynamic radar cruise control system is temporarily unavailable.
·
Misalignment of the axis of the millimeter wave radar sensor assembly
·
A Malfunction in the forward recognition camera
·
Forward recognition camera temporarily not available The cruise control is prohibited until the condition is corrected or the cruise control is turned off and back on again using the cruise control main switch. |
||
| If the following condition occurs, the ECM clears the set speed and cancels the cruise control.
·
Malfunction in the engine control system. The cruise control is disabled until the ignition switch is turned on again. |
- | - |
| If the following conditions occur while the vehicle stopped, the ECM cancels the cruise control.*1
·
The vehicle is stopped on a steep hill. |
Radar Cruise Control Unavailable Press Brake to Resume Driving |
Sounds |
| If any of the following conditions occur while the vehicle stopped, the ECM cancels the cruise control.*1
·
The driver seat belt is unfastened.
·
The driver side door is opened.
·
The vehicle is parked for a long period of time. |
- | - |
DIAGNOSIS
In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). For details, refer to the Repair Manual.