OUTLINE
A left and right independent temperature control automatic air conditioning system or multi-zone (4-zone) climate control automatic air conditioning system is provided depending on the model.
An inside-and-outside dual air layer type air conditioning unit is used. The upper layer ensures anti fogging performance by introducing outside air, and the lower layer aims for ventilation loss reduction by circulating the inside air, achieving energy conservation.
S-FLOW control is used to concentrate the air outlets on the front seats when the temperature in the cabin are stable, thus aiming for a reduction in the burden on the air conditioning to achieve energy conservation.
SPECIFICATIONS
Front Air Conditioning System
| Component | Specifications | ||
|---|---|---|---|
|
*1: Upper side *2: Lower side |
|||
| Heater Radiator Unit Sub-assembly | Type | Straight Flow Aluminum-II (SFA-II) | |
| Size (W x H x L) | 284.7 mm x 120 mm x 27 mm (11.2 in. x 4.72 in. x 1.06 in.) |
||
| Fin Pitch | 1.5 mm (0.06 in.) | ||
| Blower Motor with Fan Sub-assembly | Motor Type | DC Ferrite | |
| Fan Type | Sirocco | ||
| Fan Size (Dia. x H) | Dual Layer | 137 mm x 51 mm (5.39 in. x 2.01 in.)*1 140 mm x 35 mm (5.51 in. x 1.38 in.)*2 |
|
| Single Layer | 137 mm x 70 mm (5.40 in. x 2.76 in.) | ||
| Cooler Condenser Assembly | Type | Global Inner-fin Condenser (GIC) Multi-Flow Type Condenser (MF-IV) |
|
| Size (W x H x L) | GIC | 650 mm x 523.4 mm x 11.5 mm (25.6 in. x 20.6 in. x 0.45 in.) |
|
| MF-IV | 656 mm x 517.4 mm x 22 mm (25.8 in. x 20.4 in. x 0.87 in.) |
||
| Fin Pitch | GIC | 3.0 mm (0.12 in.) | |
| MF-IV | 3.1 mm (0.12 in.) | ||
| Cooler Compressor Assembly | Type | 10SR19 | |
| Refrigerant | Type | HFC-134a (R-134a) | |
| No. 1 Cooler Evaporator Sub-assembly | Type | Cross-turn Type Evaporator | |
| Size (W x H x L) | 306.5 mm x 231 mm x 38 mm (12.1 in. x 9.09 in. x 1.50 in.) |
||
| Fin Pitch | 2.6 mm (0.10 in.) | ||
Rear Air Conditioning System (Models with Rear Air Conditioning Unit)
| Component | Specifications | |
|---|---|---|
| Heater Radiator Sub-assembly | Type | Straight Flow Aluminum-II (SFA-II) |
| Size (W x H x L) | 130 mm x 191.1 mm x 21 mm (5.12 in. x 7.52 in. x 0.83 in.) |
|
| Fin Pitch | 1.8 mm (0.07 in.) | |
| Rear Blower Motor with Fan Sub-assembly*2 | Motor Type | DC Ferrite |
| Fan Type | Sirocco | |
| Fan Size (Dia. x H) | 140 mm x 70 mm (5.51 in. x 2.76 in.) | |
| Evaporator Sub-assembly (Rear) | Type | Cross-turn Type Evaporator |
| Size (W x H x L) | 251 mm x 145.7 mm x 38 mm (9.88 in. x 5.74 in. x 1.50 in.) |
|
| Fin Pitch | 3.0 mm (0.12 in.) | |
Rear Cooling System (Models with Rear Cooling Unit)
| Component | Specifications | |
|---|---|---|
| Rear Blower Motor with Fan Sub-assembly | Motor Type | DC Ferrite |
| Fan Type | Sirocco | |
| Fan Size (Dia. x H) | 140 mm x 70 mm (5.51 in. x 2.76 in.) | |
| Evaporator Sub-assembly (Rear) | Type | Cross-turn Type Evaporator |
| Size (W x H x L) | 251 mm x 145.7 mm x 38 mm (9.88 in. x 5.74 in. x 1.50 in.) |
|
| Fin Pitch | 3.0 mm (0.12 in.) | |
MAIN FEATURES
The air conditioning system has the following features:
| Feature | Outline |
|---|---|
| High Performance |
·
Neural network control is used, so passengers can finely control the air conditioning for maximum comfort.
·
The rear outlets are installed on the back of the center console, floor, pillar and quarter trim to ensure comfortable air conditioning performance for the rear passengers.
·
A high efficiency type clean air filter, which has a pollen removal effect, is used.
·
The blower control has 7 levels in manual mode and 31 levels in auto mode for more precise control.
·
The rear air conditioning unit is used to ensure comfortable air conditioning performance for the rear passengers.*1
·
The rear cooling unit is used to ensure comfortable cooling performance for the rear passengers.*2 |
| Light Weight |
·
A bus connector with a built-in IC is used in a lightweight wire harness design to allow a reduced number of wires.
·
The use of this connector means that pulse pattern type servo motors can be used. |
| Others | The following parts are used to ensure high cooling performance while achieving a compact and lightweight construction:
·
Semi-center Location Air Conditioning Unit
·
10SR19 Type Compressor
·
Cross-turn Type Evaporator
·
Straight Flow Aluminum (SFA)-II Heater Radiator Sub-assembly
·
Global Inner-fin Condenser (GIC)
·
Multi-Flow Type Condenser (MF-IV)
·
A [nanoeTM X]*3 generator is provided to achieve excellent air quality and comfort in the cabin. |
*1: Models with rear air conditioning unit
*2: Models with rear cooling unit
*3:
|
[nanoeTM X] is a trademark owned by Panasonic Co., Ltd. |