Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › LANE TRACING ASSIST SYSTEM
NM38G0E _95 ADAS / AD _102011 ADVANCED DRIVER ASSISTANCE SYSTEM _0478777 LANE TRACING ASSIST SYSTEM CO CONTROL F

ADVANCED DRIVER ASSISTANCE SYSTEM  LANE TRACING ASSIST SYSTEM  CONTROL  LANE TRACING ASSIST CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*: Models with headup display

Forward Recognition Camera
·

Controls the Lane Tracing Assist (LTA) system.

·

Calculates the amount of brake assist in accordance with signals from switch and ECUs.

·

Captures a view of the road ahead of the vehicle and detects lane markers on the driving lane, and calculates the radius to the center of the lane, lane width, distance from markers and heading angle deviation.

·

Sends the indicator illumination request signal, multi-information display indication request signal, and buzzer sound request signal to the combination meter assembly.

·

Receives vehicle information and turn signal light operation signals, and sends a brake control request signal to the No. 2 skid control ECU.

·

Controls the supply of electric current to the camera heater when the ambient temperature is low.


Camera Heater (Forward Recognition Hood with Heater Sub-assembly) Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up.
Millimeter Wave Radar Sensor Assembly Radiates millimeter waves forward, uses the reflected waves to detect the presence of a vehicle traveling ahead, the vehicle-to-vehicle distance, and the relative speed, and then sends this information to the forward recognition camera.
Combination Meter Assembly - Sends a turn signal command to the forward recognition camera.
LTA Indicator Illuminates in accordance with signals from the forward recognition camera.
Multi-information Display Displays a warning message and white lines to inform or warn the driver of the system condition in accordance with signals from the forward recognition camera.
Buzzer Sounds to warn the driver in accordance with signals from the forward recognition camera.
Steering Pad Switch Assembly LTA Main Switch Detects the on/off status of the LTA system and sends a signal to the forward recognition camera.
Meter Control Switch Sends a customize signal command to the combination meter assembly.
Multiplex Network Steering ECU
·

Operates the steering wheel motor according to an eccentric motor operation request signal from the forward recognition camera.

·

Each switch signal input from the steering pad switch assembly is sent to the combination meter assembly as a CXPI communication signal.


Steering Wheel Motor
·

Operates according to a signal from the multiplex network steering ECU to vibrate the steering wheel assembly.

·

Each switch signal input from the steering pad switch assembly is sent to the combination meter assembly as a CXPI communication signal.


Headup Display (Meter Mirror Sub-assembly)* The headup display receives signals from the forward recognition camera in order to display the system conditions.
Turn Signal Switch Sends a turn signal command to the steering sensor.
Steering Sensor
·

Sends the turning angle of the steering wheel to the forward recognition camera.

·

Sends a turn signal command to the combination meter assembly.


Power Steering ECU
·

Controls the power steering motor assembly according to signals from the forward recognition camera.

·

Detects steering operations performed by the driver and outputs the operations to the forward recognition camera.

·

Cancels steering assist when an abnormal torque request signal is received from the forward recognition camera.


Airbag ECU (Airbag ECU Assembly)
·

Yawrate Sensor


Detects yaw rate and sends a signal to the forward recognition camera.
Brake Actuator Assembly Brake Actuator Performs brake control of wheels on one side of the vehicle according to brake control request signals from the No. 2 skid control ECU.
No. 2 Skid Control ECU
·

Sends brake control request signals from the forward recognition camera to the brake actuator.

·

Cancels brake control when an abnormal yaw moment request is detected from the forward recognition camera.

·

Sends a vehicle speed signal to the forward recognition camera.


Transmission Control ECU Sends the shift position signal to the forward recognition camera.
Main Body ECU (Multiplex Network Body ECU) Sends country specification information signals to the forward recognition camera.
Central Gateway ECU (Network Gateway ECU) Gateway function of CAN communication.
DLC3
·

The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions.

·

The Global TechStream (GTS) can be connected to change settings as desired by the user.




OPERATION CONDITION


a.

Lane Departure Alert Function

Operation Condition
Operating The lane departure alert function is activated when all of the following conditions are met:
·

The LTA main switch is on. (When the LTA main switch is pressed to turn on the LTA system, the LTA indicator illuminates.)

·

The vehicle speed is approximately 50 km/h (32 mph) or more.

·

Lane markers or lane boundary are detected.

·

No turn signal command is detected.

·

A system malfunction is not detected.


Suspended The lane departure alert function is suspended when any one of the following conditions is met:
·

The vehicle speed is less than approximately 50 km/h (32 mph).

·

A turn signal command is detected.

·

No lane markers or lane boundary are detected.

·

The yawrate sensor is malfunctioning.

·

The vehicle crosses halfway or further over a lane marker.

·

Detection of the lane width other than regulated.

·

Immediately after the LTA system is activated.

·

A malfunction is detected in the LTA system.

·

The temperature of the forward recognition camera is abnormal.

·

Detection of the curve radius other than regulated.


Canceled/Resume The lane departure alert function is stopped when any one of the following conditions is met:
·

The LTA main switch is off.

·

The LTA system is temporarily stopped.

·

The LTA system is malfunctioning.

·

The ignition switch is turned off.


The lane departure alert function resumes when the following conditions are met:
·

The conditions to start operation listed above are satisfied.

·

The LTA system condition returns to normal.

·

The ignition switch is turned off and ON again to ensure normal operation, after the LTA system has been stopped by a system malfunction.




b.

Yaw Assist Function

Operation Condition
Operating The yaw assist function is activated when all of the following conditions are met:
·

The LTA main switch is on. (When the LTA main switch is pressed to turn on the LTA system, the LTA indicator illuminates.)

·

The vehicle speed is approximately 50 km/h (32 mph) or more.

·

Lane markers or lane boundary are detected.

·

No turn signal command is detected.

·

A system malfunction is not detected.

·

Acceleration and deceleration at or above a constant speed is not detected.

·

Steering operations to change the direction of vehicle travel are not performed.

·

Systems related to vehicle safety, such as the VSC and pre-collision system, do not operate.

·

Lane centering function is not operating.


Suspended The yaw assist function is suspended when any one of the following conditions is met:
·

The vehicle speed is less than approximately 50 km/h (32 mph).

·

A turn signal command is detected.

·

No lane markers or lane boundary are detected.

·

The yawrate sensor is malfunctioning.

·

The vehicle crosses halfway or further over a lane marker.

·

Steering operations to change the direction of vehicle travel are performed.

·

If the steering angle speed reaches a certain amount.

·

Acceleration and deceleration at or above a constant speed is detected.

·

Systems related to vehicle safety, such as the VSC and pre-collision system, operate.

·

No steering wheel operation detected.

·

Detection of the lane width other than regulated.

·

Immediately after the lane departure control function is activated.

·

A malfunction is detected in the LTA system.

·

The temperature of the forward recognition camera is abnormal.

·

Detection of the curve radius other than regulated.


Canceled/Resume The yaw assist function is stopped when any one of the following conditions is met:
·

The LTA main switch is off.

·

The LTA system is temporarily stopped.

·

The LTA system is malfunctioning.

·

The ignition switch is turned off.


The yaw assist function resumes when the following conditions are met:
·

The conditions to start operation listed above are satisfied.

·

The LTA system condition returns to normal.

·

The ignition switch is turned off and ON again to ensure normal operation, after the LTA system has been stopped by a system malfunction.




c.

Lane Centering Function

Operation Condition
Operating The lane centering function is activated when all of the following conditions are met:
·

The LTA main switch is on. (When the LTA main switch is pressed to turn on the LTA system, the LTA indicator illuminates.)

·

The vehicle speed is approximately 50 km/h (32 mph) or more.

·

When the system recognizes lane markers or the path of the preceding vehicle.

·

No turn signal command is detected.

·

A system malfunction is not detected.

·

Acceleration and deceleration at or above a constant speed is not detected.

·

Steering operations to change the direction of vehicle travel are not performed.

·

Systems related to vehicle safety, such as the VSC and pre-collision system, do not operate.

·

The hands off steering wheel alert is not displayed.

·

Lane center is turned "ON" via customized combination meter assembly settings.

·

Dynamic radar cruise control system (vehicle-to-vehicle distance control mode) is operating.

·

When calculation for a signal required for the function to operate has completed.

·

Yaw/steering assist function is not operating.


Suspended The lane centering function is suspended when any one of the following conditions is met:
·

The vehicle speed is less than approximately 50 km/h (32 mph).

·

Dynamic radar cruise control system (vehicle-to-vehicle distance control mode) do not operate.

·

A turn signal command is detected.

·

One side of lane markers or the path of the preceding vehicle is not detected.

·

The yawrate sensor is malfunctioning.

·

The vehicle crosses halfway or further over a lane marker.

·

Steering operations to change the direction of vehicle travel are performed.

·

If the steering angle speed reaches a certain amount.

·

Acceleration and deceleration at or above a constant speed is detected.

·

Systems related to vehicle safety, such as the VSC and pre-collision system, operate.

·

No steering wheel operation detected.

·

Detection of the curve radius other than regulated.

·

Detection of the lane width other than regulated.

·

A malfunction is detected in the LTA system.

·

The temperature of the forward recognition camera is abnormal.


Canceled/Resume The lane centering function is stopped when any one of the following conditions is met:
·

The LTA main switch is off.

·

The cruise control switch is off.

·

The LTA system is temporarily stopped.

·

The LTA system is malfunctioning.

·

The ignition switch is turned off.

·

Lane center is turned "OFF" via customized combination meter assembly settings.


The lane centering function resumes when the following conditions are met:
·

The conditions to start operation listed above are satisfied.

·

The LTA system condition returns to normal.

·

The ignition switch is turned off and ON again to ensure normal operation, after the LTA system has been stopped by a system malfunction.

·

Lane center is turned "ON" via customized combination meter assembly settings.




d.

Vehicle Sway Warning Function

Operation Condition
Operating The vehicle sway warning function is activated when all of the following conditions are met:
·

Sway warning is turned "ON" via customized combination meter assembly settings.

·

The vehicle speed is approximately 50 km/h (32 mph) or more.

·

Lane markers are detected.

·

No turn signal command is detected.

·

A system malfunction is not detected.


Suspended The vehicle sway warning function is suspended when any one of the following conditions is met:
·

The vehicle speed is less than approximately 50 km/h (32 mph).

·

One side of lane markers is not detected.

·

The yawrate sensor is malfunctioning.

·

Immediately after the LTA system is activated.

·

A malfunction is detected in the LTA system.

·

The temperature of the forward recognition camera is abnormal.


Canceled/Resume The vehicle sway warning function is stopped when any one of the following conditions is met:
·

The LTA system is temporarily stopped.

·

The LTA system is malfunctioning.

·

The ignition switch is turned off.

·

Sway warning is turned "OFF" via customized combination meter assembly settings.

·

Detection of the curve radius other than regulated.

·

Detection of the lane width other than regulated.

·

A turn signal command is detected.


The vehicle sway warning function resumes when the following conditions are met:
·

The conditions to start operation listed above are satisfied.

·

The LTA system condition returns to normal.

·

The ignition switch is turned off and ON again to ensure normal operation, after the LTA system has been stopped by a system malfunction.

·

Sway warning is turned "ON" via customized combination meter assembly settings.





SYSTEM CONTROL


a.

Lane Departure Alert Function

i.

If the function judges that the vehicle may deviate from the lane or lane boundary it is in, the function blinks the lane marker in the multi-information display and vibrates the steering wheel or sounds a buzzer so that the driver can take action to avoid lane departure.

Y246264E04
0.115,4.542 0.573,5.094 0.458,0.552 10 false Grass, Dirt, etc. 3.719,0.229 4.323,0.531 0.604,0.302 10 false Warning 4.927,1.625 5.531,1.927 0.604,0.302 10 false Display 3.677,3.49 4.281,3.792 0.604,0.302 10 false Warning 4.958,4.865 5.563,5.167 0.604,0.302 10 false Display 3.844,4.854 4.323,5.104 0.479,0.25 10 false Buzzer 3.875,1.604 4.354,1.854 0.479,0.25 10 false Buzzer 6.083,1.604 6.688,1.906 0.604,0.302 10 false Vibration 6.104,4.854 6.708,5.156 0.604,0.302 10 false Vibration 0.104,6.271 2.104,6.615 2,0.344 10 false This illustration is an example.



b.

Yaw Assist Function

i.

If the function judges that the vehicle may deviate from the lane or lane boundary it is in, the function performs yaw assist by operating the brakes of wheels on only one side of the vehicle to help the driver correct the path of the vehicle. If the driver does not take appropriate action, blinks the lane marker in the multi-information display and sounds a buzzer or vibratesthe steering wheel.

Y278675E02
2.302,1.177 2.469,1.177 2.469,1.177 2.635,2.094 true 2.01,1.573 2.177,1.573 2.177,1.573 2.427,2.156 true 1.385,3.281 1.552,3.281 1.552,3.281 1.802,2.531 true 2.25,3.75 2.417,3.75 2.417,3.75 2.646,5.323 true 1.833,4.083 2,4.083 2,4.083 2.406,5.396 true 1.25,4.417 1.417,4.417 1.417,4.417 1.75,4.833 true 2.25,6.417 2.083,6.417 2.083,6.417 1.802,5.771 true 0.281,4.333 1.365,4.667 1.083,0.333 10 false Grass, Dirt, etc. 3.438,4.781 4.354,4.979 0.917,0.198 10 false Buzzer 3.438,1.625 4.354,1.823 0.917,0.198 10 false Buzzer 3.344,0.26 4.26,0.458 0.917,0.198 10 false Warning 3.302,3.406 4.219,3.604 0.917,0.198 10 false Warning 4.521,4.792 5.438,4.99 0.917,0.198 10 false Display 4.583,1.615 5.5,1.813 0.917,0.198 10 false Display 0.531,3.198 1.448,3.531 0.917,0.333 10 false Brake Control 5.76,1.604 6.677,1.802 0.917,0.198 10 false Vibration 5.75,4.781 6.667,4.979 0.917,0.198 10 false Vibration 0.677,1.49 2.01,1.823 1.333,0.333 10 false Illuminates Stop Light 1.583,1.083 2.417,1.417 0.833,0.333 10 false Yaw Assist 1.531,3.667 2.365,4 0.833,0.333 10 false Yaw Assist 0.5,4 1.833,4.333 1.333,0.333 10 false Illuminates Stop Light 2.333,6.333 3.25,6.667 0.917,0.333 10 false Brake Control 0.083,6.417 2,6.75 1.917,0.333 10 false This illustration is an example.



c.

Lane Centering Function

i.

The lane centering function is linked with the dynamic radar cruise control system (vehicle-to-vehicle distance control mode) and provides the required assistance by operating the steering wheel to keep the vehicle in its current lane.*

*: When the dynamic radar cruise control system (vehicle-to-vehicle distance control mode) is not operating, the lane centering function does not operate. If the function detects that the steering wheel has not been operated for a fixed amount of time or the steering wheel is not being firmly gripped, a warning is displayed on the multi-information display and the function is temporarily canceled.


Y224353E03
5.958,1.073 7.01,1.333 1.052,0.26 10 false Steering Assist 0.115,1.885 1.448,2.156 1.333,0.271 10 false Control Output Level 0.094,2.479 2.24,2.729 2.146,0.25 10 false This illustration is an example.


ii.

The path of the preceding vehicle is used to help the driver to follow the preceding vehicle, when traffic, etc. makes it difficult or impossible to see lane markers.

Y221978E04
6.24,1.958 5.635,1.167 5.635,1.167 5.344,1.167 true 4.979,2.646 4.365,1.708 4.365,1.708 4.073,1.708 true 1.469,2.865 1.313,1.792 1.313,1.792 1.021,1.792 true 4.167,1.094 5.333,1.375 1.167,0.281 10 false Preceding Vehicle 2,1.625 4.073,1.958 2.073,0.333 10 false Driving Path of Preceding Vehicle 0.208,1.708 1.031,2.01 0.823,0.302 10 false Own Vehicle 0.083,4.417 2,4.75 1.917,0.333 10 false This illustration is an example.



d.

Vehicle Sway Warning Function

i.

The function detects drift of the vehicle within its lane, which is often the result of a driver who is tired, distracted or not looking ahead, based on the position of the vehicle within its lane and the steering inputs of the driver, to alert the driver.

Y180903E13
4.917,1.531 5.521,1.833 0.604,0.302 10 false Warning 4.396,2.021 4.906,2.354 0.51,0.333 10 false Buzzer 0.094,2.417 2.385,2.677 2.292,0.26 10 false This illustration is an example. 5.448,2.052 5.948,2.375 0.5,0.323 10 false Display


ii.

The function provides a warning to alert the driver when any of the following conditions occurs.

Y233275E02
0.208,3.302 5.104,3.5 4.896,0.198 10 false This illustration is an example. 4.781,1.927 5.875,2.5 1.094,0.573 10 false Would you like to Take a Break? 5.24,0.208 5.958,0.5 0.719,0.292 10 false Display 1.771,0.167 3.521,0.479 1.75,0.313 10 false Type of vehicle swaying 1.073,1.219 4.063,1.677 2.99,0.458 10 false The vehicle drifts within its lane when the driver is inattentive. 1.083,2.469 3.927,2.917 2.844,0.448 10 false The steering wheel is turned abruptly when the driver is inattentive.




FUNCTION


a.

The lane departure alert function and yaw assist function turn on every time the ignition switch is turned to ON. The lane departure alert function and yaw assist function can be turned off by pressing the LTA main switch of the steering pad switch assembly for 2 seconds or more.

Y278676C01
3.979,1.563 5.802,1.188 true 5.844,1.094 6.156,1.292 0.313,0.198 10 false *a
*a LTA Main Switch - -



b.

The lane centering function can be turned on and off by pressing the LTA main switch on the steering pad switch assembly or turning On and Off the Lane Center (customization function), while the ignition switch is ON.


c.

LTA System Settings Functions Customization

Item Description Setting
Lane Center Select to enable/disable the lane centering function
·

ON

·

OFF


Alert Warning Method
·

Buzzer

·

Steering Vibration


Sensitivity Timing of the lane departure alert
·

High (Graphic display)

·

Standard (Graphic display)


Sway Warning Select to enable/disable the vehicle sway warning function
·

ON

·

OFF


Sway Sensitivity Timing of the vehicle sway warning function
·

High

·

Standard

·

Low





DIAGNOSIS


a.

In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). For details, refer to the Repair Manual.