Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › LANE DEPARTURE ALERT SYSTEM
NM38G0E _95 ADAS / AD _102011 ADVANCED DRIVER ASSISTANCE SYSTEM _0478778 LANE DEPARTURE ALERT SYSTEM CO CONTROL F

ADVANCED DRIVER ASSISTANCE SYSTEM  LANE DEPARTURE ALERT SYSTEM  CONTROL  LANE DEPARTURE ALERT CONTROL  


FUNCTION OF MAIN COMPONENTS


Components Function

*1: Models with 1GR-FE engine

*2: Except models with 1GR-FE engine

Forward Recognition Camera
·

Controls the Lane Departure Alert (LDA) system.

·

Calculates the amount of brake assist in accordance with signals from switch and ECUs.

·

Captures a view of the road ahead of the vehicle and detects lane markers on the driving lane, and calculates the radius to the center of the lane, lane width, distance from markers and heading angle deviation.

·

Sends the indicator illumination request signal, multi-information display indication request signal, and buzzer sound request signal to the combination meter assembly.

·

Receives vehicle information and turn signal light operation signals, and sends a brake control request signal to the No. 2 skid control ECU.

·

Controls the supply of electric current to the camera heater when the ambient temperature is low.


Camera Heater (Forward Recognition Hood with Heater Sub-assembly) Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up.
Millimeter Wave Radar Sensor Assembly Radiates millimeter waves forward, uses the reflected waves to detect the presence of a vehicle traveling ahead, the vehicle-to-vehicle distance, and the relative speed, and then sends this information to the forward recognition camera.
Combination Meter Assembly - Sends a turn signal command to the forward recognition camera.
LDA Indicator Illuminates in accordance with signals from the forward recognition camera.
Multi-information Display Displays a warning message and white lines to inform or warn the driver of the system condition in accordance with signals from the forward recognition camera.
Buzzer Sounds to warn the driver in accordance with signals from the forward recognition camera.
Steering Pad Switch Assembly LDA Main Switch Detects the on/off status of the LDA system and sends a signal to the forward recognition camera.
Meter Control Switch Sends a customize signal command to the combination meter assembly.
Multiplex Network Steering ECU
·

Operates the steering wheel motor according to an eccentric motor operation request signal from the forward recognition camera.

·

Each switch signal input from the steering pad switch assembly is sent to the combination meter assembly as a CXPI communication signal.


Steering Wheel Motor Operates according to a signal from the multiplex network steering ECU to vibrate the steering wheel assembly.
Turn Signal Switch Sends a turn signal command to the steering sensor.
Steering Sensor
·

Sends the turning angle of the steering wheel to the forward recognition camera.

·

Sends a turn signal command to the combination meter assembly.


Airbag ECU (Airbag ECU Assembly)
·

Yawrate Sensor


Detects the yaw rate and sends a signal to the forward recognition camera.
Brake Actuator Assembly Brake Actuator Performs brake control of wheels on one side of the vehicle according to brake control request signals from the No. 2 skid control ECU.
No. 2 Skid Control ECU
·

Sends brake control request signals from the forward recognition camera to the brake actuator.

·

Cancels brake control when an abnormal yaw moment request is detected from the forward recognition camera.

·

Sends a vehicle speed signal to the forward recognition camera.


ECM*1 Sends the shift position signal to the forward recognition camera.
Transmission Control ECU*2
Main Body ECU (Multiplex Network Body ECU) Sends country specification information signals to the forward recognition camera.
Central Gateway ECU (Network Gateway ECU) Relays the signal between the CAN communication buses.
DLC3
·

The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions.

·

The Global TechStream (GTS) can be connected to change settings as desired by the user.




OPERATION CONDITION


a.

Lane Departure Alert Function

Operation Condition
Operating The lane departure alert function is activated when all of the following conditions are met:
·

The LDA main switch is on. (When the LDA main switch is pressed to turn on the LDA system, the LDA indicator illuminates in white.)

·

The vehicle speed is approximately 50 km/h (32 mph) or more.

·

Lane marker or lane boundary is detected.

·

No turn signal command is detected.

·

A system malfunction is not detected.


Suspended The lane departure alert function is suspended when any one of the following conditions is met:
·

The vehicle speed is less than approximately 50 km/h (32 mph).

·

A turn signal command is detected.

·

No lane markers or lane boundaries are detected.

·

The yawrate sensor is malfunctioning.

·

The vehicle crosses halfway or further over a lane marker.

·

Detection of the lane width other than regulated.

·

Immediately after the LDA system is activated.

·

A malfunction is detected in the LDA system.

·

The temperature of the forward recognition camera is abnormal.

·

Detection of the curve radius other than regulated.


Canceled/Resume The lane departure alert function is stopped when any one of the following conditions is met:
·

The LDA main switch is off.

·

The LDA system is temporarily stopped.

·

The LDA system is malfunctioning.

·

The ignition switch is turned off.


The lane departure alert function resumes when the following conditions are met:
·

The conditions to start operation listed above are satisfied.

·

The LDA system condition returns to normal.

·

The ignition switch is turned off and ON again to ensure normal operation, after the LDA system has been stopped by a system malfunction.




b.

Yaw Assist Function

Operation Condition
Operating The yaw assist function is activated when all of the following conditions are met:
·

The LDA main switch is on. (When the LDA main switch is pressed to turn on the LDA system, the LDA indicator illuminates in white.)

·

The vehicle speed is approximately 50 km/h (32 mph) or more.

·

Lane marker or lane boundary is detected.

·

No turn signal command is detected.

·

A system malfunction is not detected.

·

Acceleration and deceleration at or above a constant speed is not detected.

·

Steering operations to change the direction of vehicle travel are not performed.

·

Systems related to vehicle safety, such as the VSC and pre-collision system, do not operate.


Suspended The yaw assist function is suspended when any one of the following conditions is met:
·

The vehicle speed is less than approximately 50 km/h (32 mph).

·

A turn signal command is detected.

·

No lane markers or lane boundaries are detected.

·

The yawrate sensor is malfunctioning.

·

The vehicle crosses halfway or further over a lane marker.

·

Steering operations to change the direction of vehicle travel are performed.

·

If the steering angle speed reaches a certain amount.

·

Acceleration and deceleration at or above a constant speed is detected.

·

Systems related to vehicle safety, such as the VSC and pre-collision system, operate.

·

Detection of the lane width other than regulated.

·

Immediately after the LDA system is activated.

·

A malfunction is detected in the LDA system.

·

The temperature of the forward recognition camera is abnormal.

·

Detection of the curve radius other than regulated.


Canceled/Resume The yaw assist function is stopped when any one of the following conditions is met:
·

The LDA main switch is off.

·

The LDA system is temporarily stopped.

·

The LDA system is malfunctioning.

·

The ignition switch is turned off.


The yaw assist function resumes when the following conditions are met:
·

The conditions to start operation listed above returns to be satisfied.

·

The LDA system condition returns to normal.

·

The ignition switch is turned off and ON again to ensure normal operation, after the LDA system has been stopped by a system malfunction.




c.

Vehicle Sway Warning Function

Operation Condition
Operating The vehicle sway warning function is activated when all of the following conditions are met:
·

Sway warning is turned "ON" via customized combination meter assembly settings.

·

The vehicle speed is approximately 50 km/h (32 mph) or more.

·

Lane markers are detected.

·

No turn signal command is detected.

·

A system malfunction is not detected.


Suspended The vehicle sway warning function is suspended when any one of the following conditions is met:
·

The vehicle speed is less than approximately 50 km/h (32 mph).

·

One side of lane markers is not detected.

·

The yawrate sensor is malfunctioning.

·

Immediately after the LDA system is activated.

·

A malfunction is detected in the LDA system.

·

The temperature of the forward recognition camera is abnormal.

·

Detection of the curve radius other than regulated.

·

Detection of the lane width other than regulated.

·

A turn signal command is detected.


Canceled/Resume The vehicle sway warning function is stopped when any one of the following conditions is met:
·

The LDA system is temporarily stopped.

·

The LDA system is malfunctioning.

·

The ignition switch is turned off.

·

Sway warning is turned "OFF" via customized combination meter assembly settings.


The vehicle sway warning function resumes when the following conditions are met:
·

The conditions to start operation listed above returns to be satisfied.

·

The LDA system condition returns to normal.

·

The ignition switch is turned off and ON again to ensure normal operation, after the LDA system has been stopped by a system malfunction.

·

Sway warning is turned "ON" via customized combination meter assembly settings.





SYSTEM CONTROL


a.

Lane Departure Alert Function

i.

If the LDA system judges that the vehicle may deviate from the lane it is in, the LDA system blinks the lane marker in the multi-information display and vibrates the steering wheel or sounds a buzzer so that the driver can take action to avoid lane departure.

Y246264E04
0.115,4.542 0.573,5.094 0.458,0.552 10 false Grass, Dirt, etc. 3.719,0.229 4.323,0.531 0.604,0.302 10 false Warning 4.927,1.625 5.531,1.927 0.604,0.302 10 false Display 3.677,3.49 4.281,3.792 0.604,0.302 10 false Warning 4.958,4.865 5.563,5.167 0.604,0.302 10 false Display 3.844,4.854 4.323,5.104 0.479,0.25 10 false Buzzer 3.875,1.604 4.354,1.854 0.479,0.25 10 false Buzzer 6.083,1.604 6.688,1.906 0.604,0.302 10 false Vibration 6.104,4.854 6.708,5.156 0.604,0.302 10 false Vibration 0.104,6.271 2.104,6.615 2,0.344 10 false This illustration is an example.



b.

Yaw Assist Function

i.

If the LDA system judges that the vehicle may deviate from the lane it is in, the LDA system performs yaw assist by operating the brakes of wheels on only one side of the vehicle to help the driver correct the path of the vehicle. If the driver does not take appropriate action, the LDA system blinks the lane marker in the multi-information display and sounds a buzzer or vibrates the steering wheel.

Y278675E02
2.302,1.177 2.469,1.177 2.469,1.177 2.635,2.094 true 2.01,1.573 2.177,1.573 2.177,1.573 2.427,2.156 true 1.385,3.281 1.552,3.281 1.552,3.281 1.802,2.531 true 2.25,3.75 2.417,3.75 2.417,3.75 2.646,5.323 true 1.833,4.083 2,4.083 2,4.083 2.406,5.396 true 1.25,4.417 1.417,4.417 1.417,4.417 1.75,4.833 true 2.25,6.417 2.083,6.417 2.083,6.417 1.802,5.771 true 0.281,4.333 1.365,4.667 1.083,0.333 10 false Grass, Dirt, etc. 3.438,4.781 4.354,4.979 0.917,0.198 10 false Buzzer 3.438,1.625 4.354,1.823 0.917,0.198 10 false Buzzer 3.344,0.26 4.26,0.458 0.917,0.198 10 false Warning 3.302,3.406 4.219,3.604 0.917,0.198 10 false Warning 4.521,4.792 5.438,4.99 0.917,0.198 10 false Display 4.583,1.615 5.5,1.813 0.917,0.198 10 false Display 0.531,3.198 1.448,3.531 0.917,0.333 10 false Brake Control 5.76,1.604 6.677,1.802 0.917,0.198 10 false Vibration 5.75,4.781 6.667,4.979 0.917,0.198 10 false Vibration 0.677,1.49 2.01,1.823 1.333,0.333 10 false Illuminates Stop Light 1.583,1.083 2.417,1.417 0.833,0.333 10 false Yaw Assist 1.531,3.667 2.365,4 0.833,0.333 10 false Yaw Assist 0.5,4 1.833,4.333 1.333,0.333 10 false Illuminates Stop Light 2.333,6.333 3.25,6.667 0.917,0.333 10 false Brake Control 0.083,6.417 2,6.75 1.917,0.333 10 false This illustration is an example.

HINT:
·

The stop lights may not illuminate in some situations.





c.

Vehicle Sway Warning Function

i.

The LDA system detects drift of the vehicle within its lane, which is often the result of a driver who is tired, distracted or not looking ahead, based on the position of the vehicle within its lane and the steering inputs of the driver, to alert the driver before a lane departure or collision occurs.

Y180903E13
4.917,1.531 5.521,1.833 0.604,0.302 10 false Warning 4.396,2.021 4.906,2.354 0.51,0.333 10 false Buzzer 0.094,2.417 2.385,2.677 2.292,0.26 10 false This illustration is an example. 5.448,2.052 5.948,2.375 0.5,0.323 10 false Display


ii.

The vehicle sway warning function provides a warning to alert the driver when any of the following conditions occur:

Y233275E05
0.208,3.302 5.104,3.5 4.896,0.198 10 false This illustration is an example. 4.781,1.927 5.979,2.469 1.198,0.542 10 false Would You Like to Take a Break? 5.24,0.208 5.958,0.5 0.719,0.292 10 false Display 1.771,0.167 3.521,0.479 1.75,0.313 10 false Type of vehicle swaying 1.073,1.219 4.063,1.677 2.99,0.458 10 false The vehicle drifts within its lane when the driver is inattentive. 1.083,2.469 3.927,2.917 2.844,0.448 10 false The steering wheel is turned abruptly when the driver is inattentive.




FUNCTION


a.

The LDA system can be turned on/off by pressing the LDA main switch on the steering pad switch assembly while the engine is started.

HINT:

When the ignition switch is turned from off to ON, the LDA system turns on.


Y278676C01
3.979,1.563 5.802,1.188 true 5.844,1.094 6.156,1.292 0.313,0.198 10 false *a
*a LDA Main Switch - -



b.

LDA system Settings Functions Customization

Item Description Setting
Alert Warning method
·

Buzzer

·

Steering Vibration


Sensitivity Timing of the lane departure alert
·

High

·

Standard


Sway Warning Select to enable/disable the vehicle sway warning function
·

ON

·

OFF


Sway Sensitivity Timing of the vehicle sway warning function
·

High

·

Standard

·

Low





DIAGNOSIS


a.

In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). For details, refer to the Repair Manual.