Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › ADAPTIVE HIGH BEAM SYSTEM
NM38G0E _95 ADAS / AD _102011 ADVANCED DRIVER ASSISTANCE SYSTEM _0478780 ADAPTIVE HIGH BEAM SYSTEM CO CONTROL F

ADVANCED DRIVER ASSISTANCE SYSTEM  ADAPTIVE HIGH BEAM SYSTEM  CONTROL  ADAPTIVE HIGH BEAM SYSTEM (AHS) CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
Light Control LED ECU RH Receives signals from various sensors and controls the headlight illuminations based on the conditions of the vehicle and surroundings.
Light Control LED ECU LH
Headlight ECU Sub-assembly RH
·

Receives signals from various sensors and controls the headlight brightness and illumination area based on the conditions of the vehicle and surroundings.

·

Sends Adaptive High beam System (AHS) control request signals to the light control LED ECU.

·

Stores DTCs when a malfunction is detected in the AHS.


Headlight ECU Sub-assembly LH
Forward Recognition Camera
·

Captures an image of the area in front of the vehicle and uses the image to determine the position of preceding and oncoming vehicles and to determine the brightness of the surrounding area. This data is then sent to the headlight ECU sub-assembly LH via CAN communication.

·

Controls the supply of electric current to the camera heater when the ambient temperature is low.


Camera Heater (Forward Recognition Hood with Heater Sub-assembly) Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up.
Turn Signal Switch Light Control Switch Sends the light control switch signals to the steering sensor.
Dimmer Switch Sends the dimmer switch signals to the steering sensor.
Auto High Beam Switch Sends the auto high beam main switch signals to the steering sensor.
Steering Sensor Sends the light control switch, dimmer switch and auto high beam main switch signals to the main body ECU.
Main Body ECU (Multiplex Network Body ECU)
·

Receives signals from the steering sensor and automatic light control sensor.

·

Controls the headlight ECU sub-assembly LH and headlight ECU sub-assembly RH based on signals from various sensors and switches.

·

Sends illumination request signals for the adaptive high beam indicator and high beam indicator to the combination meter assembly according to the operation condition of the headlight system.


Automatic Light Control Sensor Detects the ambient light level and transmits a signal to the main body ECU.
No. 2 Skid Control ECU Sends the vehicle speed signal to the combination meter assembly.
Combination Meter Assembly
·

Sends the vehicle speed signal to the main body ECU.

·

Illuminates the adaptive high beam indicator to inform the driver when the AHS is activated.

·

Illuminates the high beam indicator light to inform the driver when the beams are on.


Transmission Control ECU Sends the shift position signals to the headlight ECU sub-assembly LH.
Central Gateway ECU (Network Gateway ECU) Relays the signal between the CAN communication lines.
DLC3 The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions.


OPERATING CONDITION


a.

The AHS operates when all of the following conditions are met. While the AHS is on, the adaptive high beam indicator light illuminates.

·

The ignition switch is ON.

·

The light control switch is in the HEAD position and AUTO position and the headlights are operating.

·

The dimmer switch is in the LO position.

·

The auto high beam switch is on.*

·

The vehicle speed is approximately 15 km/h (9 mph) or more.


HINT:

*: When the auto high beam switch is turned on while the headlights are not illuminated or the dimmer switch in a position other than LO, a message is displayed on the multi-information display.




SYSTEM CONTROL


a.

High Beam Light Distribution Control Function

i.

In high beam light distribution control function, the headlight control ECU sub-assemblies control the brightness and illumination area of the high beam.


ii.

The high beam light distribution control function, changes the intensity and illumination area according to 3 vehicle speed ranges:

Illumination Mode Description of Function Vehicle Speed

*1: Except models for Europe

*2: Models for Europe

Low Speed Mode (Town Mode)
·

Widens the illuminated area.

·

The brightness of the headlights is adjusted to ensure that pedestrians are visible while not being dazzled.

·

Reduces illumination of the side of the road.


15 - 30 km/h (9 - 19 mph)
Normal Mode
·

At medium speeds, the illuminated area in front of the vehicle is extended and necessary areas to the left and right of the vehicle are illuminated.

·

Reduces the light distribution at the center of the high beams when driving in rainy weather to prevent glare from oncoming vehicles caused by camera recognition delays.


30 - 80 km/h (19 - 50 mph)*1
30 - 120 km/h (19 - 75 mph)*2
High Speed Mode
·

The illuminated area in front of the vehicle is narrowed.

·

Adjusts the high beams to ensure visibility far in front of the vehicle.

·

Reduces the light distribution at the center of the high beams when driving in rainy weather to prevent glare from oncoming vehicles caused by camera recognition delays.


80 km/h (50 mph) or more*1
120 km/h (75 mph) or more*2

Low Speed Mode (Town Mode)
Y189250C01
3.719,1.26 3.521,0.313 3.521,0.313 2.615,0.313 true 3.979,2.479 4.24,3.604 4.24,3.604 4.875,3.604 true 2.448,0.229 2.719,0.479 0.271,0.25 10 false *a 4.979,3.51 5.25,3.698 0.271,0.188 10 false *b
*a Area Illuminated by High Beams *b Area Illuminated by Low Beams


Normal Mode
Y189251C03
5.833,3.344 5.333,3.344 5.333,3.344 5.135,2.563 true 2.99,0.563 3.5,0.563 3.5,0.563 3.646,1.229 true 2.813,0.479 3.073,0.698 0.26,0.219 10 false *a 5.906,3.271 6.219,3.427 0.313,0.156 10 false *b
*a Area Illuminated by High Beams *b Area Illuminated by Low Beams


High Speed Mode
Y189252C03
3.625,1.229 3.76,0.458 3.76,0.458 4.219,0.458 true 3.646,2.51 3.438,3.573 3.438,3.573 2.698,3.573 true 4.281,0.396 4.594,0.604 0.313,0.208 10 false *a 2.531,3.51 2.844,3.667 0.313,0.156 10 false *b
*a Area Illuminated by High Beams *b Area Illuminated by Low Beams




b.

Light Disable Control Function

i.

The light disable control function dims LEDs in the high beam headlight accordingly when the forward recognition camera detects a preceding vehicle or an oncoming vehicle.


ii.

The light control LED ECU and LED unit enable the LEDs of the headlight assembly to be dimmed independently as necessary.

Y189253C03
4.906,2.854 5.208,2.854 5.208,2.854 5.323,2.271 true 0.896,1 1.229,1 1.229,1 1.292,1.344 true 0.885,0.729 1.854,0.729 1.854,0.729 1.958,1.302 true 3.115,0.781 2.885,0.781 2.885,0.781 2.813,1.302 true 1.292,2.99 1.594,2.99 1.594,2.99 1.708,2.406 true 4.313,0.958 4.448,0.958 4.448,0.958 4.51,1.302 true 4.292,0.74 5.042,0.74 5.042,0.74 5.188,1.333 true 6.698,0.948 6.552,0.948 6.552,0.948 6.5,1.271 true 0.292,0.615 0.604,0.802 0.313,0.188 10 false *A 3.792,0.583 4.104,0.74 0.313,0.156 10 false *B 4.719,2.781 5,2.969 0.281,0.188 10 false *b 0.729,0.646 0.958,0.844 0.229,0.198 10 false *a 0.729,0.927 0.99,1.115 0.26,0.188 10 false *a 3.156,0.698 3.417,0.885 0.26,0.188 10 false *a 1.104,2.917 1.385,3.104 0.281,0.188 10 false *b 4.146,0.667 4.406,0.854 0.26,0.188 10 false *a 6.729,0.865 6.99,1.063 0.26,0.198 10 false *a 4.156,0.875 4.417,1.063 0.26,0.188 10 false *a
*A When driving on road with one lane in each direction *B When driving on a multi-lane road
*a Area Illuminated by High Beams *b Area Illuminated by Low Beams




c.

Headlight Swivel Control Function

i.

The headlight swivel control function adjusts the brightness of headlights while turning a corner to ensure excellent visibility.

Y189254C03
1.781,1.646 1.719,1.063 1.719,1.063 1.021,1.063 true 1.781,2.396 1.708,3.063 1.708,3.063 0.979,3.063 true 6.208,1.656 6.302,1.063 6.302,1.063 6.656,1.063 true 6.031,2.281 6.135,2.969 6.135,2.969 6.625,2.969 true 0.813,0.979 1.125,1.135 0.313,0.156 10 false *a 0.823,2.979 1.094,3.208 0.271,0.229 10 false *b 6.729,0.99 6.948,1.198 0.219,0.208 10 false *a 6.667,2.896 6.938,3.125 0.271,0.229 10 false *b
*a Area Illuminated by High Beams *b Area Illuminated by Low Beams




d.

Cut-off Line Tilt Control Function

i.

The cut-off line tilt function controls the leveling motor built into the headlight assembly to optimize the illumination area of the low beams in accordance with the distance to the preceding vehicle detected by the forward recognition camera.

Y189255C01
1.917,0.896 2.531,0.896 2.531,0.896 2.833,1.906 true 5.396,2.771 4.521,2.771 4.521,2.771 4.24,1.844 true 1.219,5.24 1.719,5.24 1.719,5.24 1.781,4.792 true 4.708,5.24 5.146,5.24 5.146,5.24 5.229,4.844 true 6.188,3.875 5.677,3.875 5.677,3.875 5.552,4.573 true 1.729,0.813 2.031,1.021 0.302,0.208 10 false *a 5.448,2.719 5.781,3 0.333,0.281 10 false *b 1.052,5.156 1.354,5.365 0.302,0.208 10 false *a 4.531,5.177 4.833,5.385 0.302,0.208 10 false *a 6.229,3.802 6.563,4.083 0.333,0.281 10 false *b
*a Illumination Area of Low Beams without Control *b Illumination Area of Low Beams during Control





FUNCTION


a.

The AHS operates when the auto high beam switch is on, the light control switch is in the HEAD or AUTO position and the dimmer switch is set to LO. The AHS uses the forward recognition camera to detect the lights of oncoming vehicles and the taillights of preceding vehicles and to determine the brightness of the surrounding area in order to select which LEDs of the LED array to illuminate.


b.

The headlight ECU sub-assemblies control the AHS.


c.

When the AHS is on, the adaptive high beam indicator light in the combination meter assembly illuminates.



FAIL-SAFE


a.

The headlight ECU sub-assemblies prohibit operation of the AHS if a malfunction is detected in the system.