OUTLINE
The Automatic High Beam (AHB) system detects lights of preceding and oncoming vehicles and automatically changes between high beams and low beams to support the driver during night driving.
PRECAUTION
High beam/low beam switching operation
Operate the system as follows to switch the headlights manually to high beams/low beams.
Turn the auto high beam switch off. The vehicle switches to low beams based on the dimmer switch position (low). To switch to high beams, move the dimmer switch to the high position.
Move the dimmer switch from the low position to the high position. The high beams will turn on based on the dimmer switch position (high).
Surrounding light conditions for automatic high beam operation
The area to the front of the vehicle is monitored by the forward recognition camera installed on the windshield glass. The automatic high beams operate when the surrounding area is dark, there are no headlights from oncoming vehicles or taillights from preceding vehicles and it is determined that it would be appropriate to turn the high beams on. The system may therefore operate unexpectedly in the following situations.
The low beams will stay on if the surrounding area is not dark, even if the indicator in the combination meter assembly is on.
If an oncoming vehicle approaches from a sharp curve or crosses in front of the vehicle, the high beams may stay on.
The fog lights of an oncoming vehicle may cause the high beams to turn off.
The timing at which the high beams turn on and off may differ depending on the brightness of headlights or fog lights (oncoming vehicles) or taillights and rear fog lights (preceding vehicles).
When traveling on a wet, frozen or snowy road, the timing at which the high beams turn on and off may differ from normal (during fine weather).
The timing at which the high beams turn on and off may differ depending on the number of passengers and amount of luggage.
The high beams may rarely be turned off in a state unexpected by the driver.
The system may recognize light from a source other than a vehicle to the front and turn the high beams off. (Examples include signs, reflective objects, traffic signals and other light sources)
The timing at which the high beams turn on and off may differ when driving in an environment outside of the country in which the vehicle was purchased (such as driving a right-hand drive vehicle on the right side of the road).
Timing at which the automatic high beams turn the high beams on
The forward recognition camera will continue to monitor surrounding light to the front of the vehicle for approximately 1 second, even if the surrounding area is dark and there are no headlights from oncoming vehicles or taillights from preceding vehicles. The high beams will therefore not turn on instantaneously even if there is no surrounding light.
Windshield glass replacement
The timing at which the high beams turn on or off may vary due to differences in the permeability of the glass. Therefore, when replacing windshield glass, use only proper (genuine) windshield glass from a proper dealer. When replacing the glass, be sure also to adjust (aim) the optical axis of the forward recognition camera.
Handling the forward recognition camera
Keep the following precautions in mind to prevent malfunctions.
Do not directly touch the lens of the forward recognition camera.
Do not stick anything to the lens of the forward recognition camera.
Do not subject the forward recognition camera to a strong impact.
Do not allow liquid to drip on the lens of the forward recognition camera.
Other situations where the automatic high beams will not operate
The automatic high beams may not operate if the temperature inside the vehicle cabin is high.
The system may not operate if a tag or other object preventing images from being captured is attached in front of the forward recognition camera.
General precautions
The automatic high beams help to maintain visibility for the driver by automatically turning the headlight high beams on and off. There are limitations to the automatic high beam control provided by the automatic high beams.
When driving, remain constantly aware of your surroundings, switch the high beams on and off manually as needed and drive safely while directly confirming safety in the surrounding area.
The system may not operate if the windshield glass in front of the forward recognition camera is fogged up.
The system may not operate in bad weather (rain, fog).
Conditions unsuitable for using the automatic high beams
Vehicles and light cannot be detected in the surrounding area under the following conditions. Do not use the automatic high beams. Instead, manually switch the high beams on and off.
Caused by weather/climate
During bad weather (such as rain, snow, fog or dust storm)
High temperature inside cabin
Vehicle is driven on a snow-covered road and taillights of preceding vehicle are not visible due to kicked-up snow
Caused by windshield glass
Windshield glass is not clear (frozen, snowy or foggy)
Windshield glass is dirty (sticking sand, mud, water scales, insects, etc.)
Windshield glass is cracked
Windshield glass is fogged up
Windshield glass has film applied
An object placed on the instrument panel is reflected in the windshield glass
There is something else out of the ordinary with the windshield glass
Caused by forward recognition camera
The forward recognition camera is deformed
The forward recognition camera is dirty
There is some other forward recognition camera malfunction (high temperature, etc.)
Caused by vehicle/light in surrounding area
There is light similar to headlights or taillights in the surrounding area
There is a vehicle to the front with its lights off, without lights, with lights of an atypical color or with a misaligned beam axis
There is a vehicle to the front with extremely dirty headlights or taillights
Caused by road conditions
The brightness of the surrounding area changes frequently between light and dark
The height of the road changes frequently between high and low
The curve of the road changes frequently or the curve of the road is sharp
The road is bumpy (rocky road, gravel road or unpaved rough road)
There is a highly reflective object (mirror, sign, etc.) to the front
Caused by own vehicle
The headlights are damaged, deformed or dirty
The vehicle is driven while tilted forward/backward or to the left/right (due to a puncture, excessive load, being towed, etc.)
There is some other malfunction or the vehicle has been modified
Caused by automatic high beam malfunction
The automatic high beam indicator in the combination meter assembly is off
Caused by automatic high beams in general
The timing at which the high beams are switched by the automatic high beams feels abnormal or changes occur frequently
High beams may be a nuisance to surrounding vehicles and people (due to glare, etc.) for other reasons
The automatic high beams frequently turn the headlight high beams on and off