FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
| Headlight ECU Sub-assembly RH | Receives the headlight control signal from the main body ECU and changes between the high beams and low beams. | |
| Headlight ECU Sub-assembly LH | ||
| Forward Recognition Camera |
·
Determines when to turn the high beams on and off after identifying the lights of oncoming vehicles, preceding vehicles and other lights from the picture information of its camera sensor. Then, the sensor sends high beam request signals to the headlight ECU sub-assembly LH.
·
Controls the supply of electric current to the camera heater when the ambient temperature is low. |
|
| Camera Heater (Forward Recognition Hood with Heater Sub-assembly) | Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up. | |
| Main Body ECU (Multiplex Network Body ECU) | Receives each sensor and switch condition and illuminates or turns off the lights. | |
| Automatic Light Control Sensor | Detects the ambient light level and transmits a signal to the main body ECU. | |
| Turn Signal Switch | Light Control Switch | Sends the light control switch signals to the steering sensor. |
| Dimmer Switch | Sends the dimmer switch signals to the steering sensor. | |
| Auto High Beam Switch | Sends the auto high beam switch signals to the steering sensor. | |
| Steering Sensor | Sends the light control switch, dimmer switch and auto high beam main switch signals to the main body ECU. | |
| No. 2 skid control ECU | Sends the vehicle speed signal to the combination meter assembly. | |
| Combination Meter Assembly |
·
Sends the vehicle speed signal to the main body ECU.
·
Illuminates the automatic high beam indicator to inform the driver when the Automatic High Beam (AHB) system is activated.
·
Illuminates the high beam indicator to inform the driver when the high beams are on. |
|
| Central Gateway ECU (Network Gateway ECU) | Relays the signal between the CAN communication lines. | |
| DLC3 | The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions. | |
SYSTEM CONTROL
| Function | Operation Condition |
|---|---|
| Active | When all of the following conditions are met, the AHB system is activated and the automatic high beam indicator turns on:
·
The ignition switch is ON.
·
The light control switch is in the AUTO or HEAD position and the low beam headlights are on.
·
The dimmer switch is in the low beam position.
·
The auto high beam switch is ON.
·
The shift position is in any position other than R. |
| High Beams on | When all of the following conditions are met, the AHB system turns on the high beams after a short delay:
·
Vehicle speed is more than approximately 30 km/h (18 mph).
·
The area in front of the vehicle is dark.
·
No oncoming vehicles are present with the headlights on.
·
No preceding vehicles are present with the taillights on.
·
Few streetlights are present along the street ahead. |
| High Beams off | When any of the following conditions is met, the AHB system turns off the high beams after a short delay:
·
Vehicle speed is less than approximately 25 km/h (15 mph).
·
The area in front of the vehicle is not dark.
·
An oncoming vehicle with headlights on is detected.
·
A preceding vehicle with taillights on is detected.
·
Several streetlights are present along the street ahead. |
FUNCTION
When the forward recognition camera detects an oncoming and/or a preceding vehicle in the AHB system operation range, the AHB system turns the high beam off.
When an oncoming and/or a preceding vehicle passes out of forward recognition camera range, the AHB system turns the high beam on after a short delay.
| *a | When Passing an Oncoming Vehicle | *b | When Passing a Preceding Vehicle |
| *c | Automatic High Beam Operation Range | *d | Delay |
| *e | Automatic High Beam Operation Angle | - | - |
The detection distance varies depending on detected objects.
The timing of turning on and off the high beams varies depending on the intensity of oncoming (and preceding) vehicle lights.
DIAGNOSIS
In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The Diagnostic Trouble Codes (DTCs) of malfunctions can be read by connecting the Global TechStream (GTS). For details, refer to the Repair Manual.