CONSTRUCTION
Resilience Frame
A adopted a lightweight and highly rigid frame that has both the strength and suppleness to repel strong external forces. (*A in illustration
| *a | Frame | - | - |
In order to obtain the optimum side rail cross-sectional characteristics, the cross-sectional height of the parts that are susceptible to stress when driving on rough roads has been increased.
| *a | A - A Cross Section | *b | B - B Cross Section |
| *c | Conventional Construction | *d | Widening |
The weight has been reduced by optimally arranging the cross members. (*A in illustration)
| *a | Cross Member | - | - |
Thick plate steel and ultra high-tensile strength steel and high-tensile strength steel are used for each part in order to realize a strong and high-altitude frame with excellent robustness.
Applicable part of thick steel plate
| *a | Thickness: 3.6 - 5.0 mm (0.142 - 0.197 inch) | - | - |
Where to apply ultra high-tensile strength steel and high-tensile strength steel
| *a | Ultra High-tensile Strength Steel (Tensile Strength: 980 MPa Class) | *b | High-tensile Strength Steel (Tensile Strength: 780 MPa Class) |
| *c | High-tensile Strength Steel (Tensile Strength: 590 MPa Class) | - | - |
TWB* is used for some of the side rails and cross members. As a result, the weight has been significantly reduced while maintaining the strength and rigidity of the frame.
Tailor Welded Blank : Multiple steel materials with different plate thicknesses, materials, surface treatments, etc. are welding joined, and then press-molded.
| *A | Cutting Process | *B | Welding Process |
| *C | Press Process | - | - |
| *a | A - A Cross Section | *b | B - B Cross Section |
| *c | C - C Cross Section | *d | Reinforcing Material (Thick Plate) |
| *e | Base material (Thin Plate) | - | - |
| *A | The material is cut from the base material (thin plate) and the reinforcing material (thick plate) and combined. |
| *B | The base material and the reinforcing material are combined by laser welding to form a single plate. |
| *C | Molded by press processing. |
In the past, many reinforcements were used to ensure strength, but by increasing the thickness of the right material in the right place with TWB, we have achieved both strength and rigidity maintenance and weight reduction.
| *A | Conventional Construction | *B | TWB |
| *a | A - A Cross Section | *b | Reinforcement |
Bridge Structure Front Cross Member
The steering stability has been improved by adopting a front cross member with a bridge structure.
| *1 | Front Cross Member | - | - |
A built-in structure of the towing receiver (*A in illustration) is used for the high-rigidity, high-strength rear cross member to achieve high towing capacity and running stability during towing. In addition, the weight has been reduced by adopting TWB.
| *A | Weight Distribution Type | *B | Except Weight Distribution Type |
| *a | Thickness: 5.0 mm (0.197 inch) (*A) Thickness: 4.5 mm (0.177 inch) (*B) |
*b | Thickness: 3.6 mm (0.142 inch) |
Aluminum, high-tensile strength steel, ultra high-tensile strength steel and hot-stamped steel are used in order to achieve excellent body rigidity and a lightweight body.
| *a | Hot-stamped Steel (Tensile Strength: 1500 MPa Class) | *b | Ultra High-tensile Strength Steel (Tensile Strength: 1180 MPa Class) |
| *c | Ultra High-tensile Strength Steel (Tensile Strength: 980 MPa Class) | *d | Aluminum |
| *a | High-tensile Strength Steel (Tensile Strength: 780 MPa Class) | *b | Ultra High-tensile Strength Steel (Tensile Strength: 1180 MPa Class) |
| *c | Ultra High-tensile Strength Steel (Tensile Strength: 980 MPa Class) | - | - |
Roof Panel
A bead is set on the roof panel to ensure surface rigidity. In addition, the roof panel is made of aluminum to reduce weight and lower the center of gravity to improve steering stability.
| *A | Models with Sliding Roof | *B | Models without Sliding Roof |
| *a | Bead | - | - |
Engine Under Cover
GFRP* is used for the engine undercover to achieve a significant weight reduction while maintaining strength compared to conventional steel products.
A material that is made by hardening woven glass fiber with polyester resin, etc., and has excellent strength, rigidity, and lightness.
A structure that inserts steel into the joint with the body and the part where the road surface interference is severe has been adopted to achieve high running performance.
| *a | A - A Cross Section | *b | Resin |
| *c | Steel | *d | GFRP |
| *e | Glass Fiber Woven Graphic Image | - | - |