Home › Power Source / Network › POWER DISTRIBUTION › POWER INTEGRATION SYSTEM
NM38G0E _57 Power Source / Network _102006 POWER DISTRIBUTION _0480576 POWER INTEGRATION SYSTEM CO CONTROL F

POWER DISTRIBUTION  POWER INTEGRATION SYSTEM  CONTROL  POWER INTEGRATION CONTROL  


FUNCTION OF MAIN COMPONENTS


Components Function

*1: Models with front fog light

*2: Models with rear fog light

*3: Models with mirror heater system

*4: Models with stop and start system

*5: Models with projector type headlight

*6: Models with reflector type headlight

Semiconductor Power Integration ECU
·

Receives signals from ECUs and switches, and then drives each component.

·

Shuts off current when a malfunction occurs.

·

Performs multiplex communication with the DLC3 and ECUs.


Power Distribution Box Assembly
Fog Light Unit LH Front Fog Light LH*1 Illuminates when the front fog switch is turned on.
Fog Light Unit RH Front Fog Light RH*1
Rear Combination Light Assembly LH Taillight Illuminates according to certain conditions, such as when driving at night.
Rear Combination Light Assembly RH Taillight
Rear Light Assembly LH Taillight Illuminates according to certain conditions, such as when driving at night.
Rear Fog Light*2 Illuminates when the rear fog switch is turned on.
Rear Light Assembly RH Taillight Illuminates according to certain conditions, such as when driving at night.
Rear Fog Light*2 Illuminates when the rear fog switch is turned on.
License Plate Light Assembly LH Illuminates according to certain conditions, such as when driving at night.
License Plate Light Assembly RH
Rear Window Defogger Wire Generates heat when current is applied, warming the rear window.
Outer Rear View Mirror Assembly LH Mirror Heater*3 Generates heat when current is applied, warming the mirror surface.
Outer Rear View Mirror Assembly RH Mirror Heater*3 Generates heat when current is applied, warming the mirror surface.
Heater Water Pump (Heater Accessory Assembly)*4 Circulates coolant to ensure a stable heat source for the heater during idling stop control.
Compressor with Pulley Assembly Magnetic Clutch Transmits the engine rotation via the fan and generator V belt, when the air conditioning operation signal is inputted.
Windshield Washer Jar Assembly Level Warning Switch Assembly Detects when the washer fluid level is low.
Main Body ECU (Multiplex Network Body ECU)
·

Controls the body control systems.

·

Receives component operation requests and sends them to the power distribution box assembly.


Headlight ECU Sub-assembly*5
·

Controls the headlight system.

·

Receives operation request signals from the semiconductor power integration ECU and outputs illumination command signals to the headlights.


LED Driver Module (Light Control LED ECU)*6
Air Conditioning Amplifier Assembly
·

Controls the air conditioning system.

·

Sends rear window defogger and mirror heater operation request signals to the main body ECU.


Central Gateway ECU (Network Gateway ECU) Relays the signal between the CAN communication lines.
DLC3 Connects to the Global TechStream (GTS).


FUNCTION


Communication Support of Power Distribution Box Assembly
Components Operation Signal Communication Support

*1: Models with projector type headlight

*2: Models with reflector type headlight

*3: Models with front fog light

*4: Models with rear fog light

*5: Models with mirror heater system

Headlight ECU Sub-assembly*1 X
LED Driver Module (Light Control LED ECU)*2 X
Fog Light Assembly*3 ○
Taillight
License Plate Light Assembly
○
Rear Fog Light*4 ○
Illumination Lights ○
Magnetic Clutch X
Level Warning Switch Assembly ○
Rear Window Defogger Wire ○
Mirror Heater*5 ○

HINT:

○: Supported

X: Not supported


a.

Component Operation Output Function

i.

This function turns the corresponding component on and off in accordance with operation signals or switch input signals from the ECU.



b.

Semiconductor Fuse Function

i.

When an abnormal electric current occurs during operation of components, the components are turned off by shutting off the current before electrical wire emits smoke.


ii.

The electrical current is maintained shut off while operation signals or switch signals are on.


iii.

When operation signals or switch signals are turned off, the shut off condition is canceled.

Y204520E02
4.167,3.583 4.344,3.583 4.344,3.583 4.5,3.167 true 2.833,3.563 3.01,3.563 3.01,3.563 3.156,3.167 true 3.646,0.469 4.76,0.771 1.115,0.302 10 false Overcurrent 6.177,0.51 6.698,0.823 0.521,0.313 10 false Normal 1.563,0.458 2.042,0.729 0.479,0.271 10 false Normal 1.063,1.271 1.375,1.469 0.313,0.198 10 false Met 0.167,1.49 0.875,2.146 0.708,0.656 10 false Output On Condition 0.833,1.917 1.406,2.167 0.573,0.25 10 false Not Met 1.125,2.552 1.344,2.76 0.219,0.208 10 false On 1.115,3.198 1.396,3.396 0.281,0.198 10 false Off 0.271,2.906 1.073,3.167 0.802,0.26 10 false Component 2.083,3.469 2.875,3.719 0.792,0.25 10 false Maintaining 3.448,3.5 4.271,3.76 0.823,0.26 10 false Maintaining 3.563,2.188 4.177,2.417 0.615,0.229 10 false Cancel 4.875,2.198 5.469,2.49 0.594,0.292 10 false Cancel



c.

Multiplex Communication Function

i.

Operation Signal Communication

·

This communication uses the multiplex communication line (CXPI communication line) to input operation signals or switch signals from the ECU.



ii.

Diagnosis Communication

·

Checking Diagnostic Trouble Codes (DTCs) regarding ECU and other malfunctions is possible by connecting the Global TechStream (GTS).

·

The semiconductor fuse condition (shut off or not) can be confirmed by connecting the Global TechStream (GTS).



iii.

Reprogramming

·

Reprogramming can be performed by connecting the Global TechStream (GTS).


HINT:

Refer to the Repair Manual for the details of the diagnostic communication and reprogramming.





DIAGNOSIS


a.

In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The Diagnostic Trouble Codes (DTCs) of malfunctions can be read by connecting the Global TechStream (GTS). For details, refer to the Repair Manual.