FUNCTION OF MAIN COMPONENTS
The main components in the wireless door lock control system have the following functions:
| Component | Outline | |
|---|---|---|
|
*1: Models without theft sensor cancel switch *2: Models with theft sensor cancel switch *3: Models with tire pressure warning system *4: Models without tire pressure warning system *5: Models with power back door system *6: Models without power back door system |
||
| No. 1 Engine Room Relay Block | Horn Relay Assembly (HORN) | Inputs sounding request signals from the main body ECU and operates the high pitched horn assembly and low pitched horn assembly. |
| Security Warning Relay (S-HORN)*1 | Inputs sounding request signals from the main body ECU and operates the security horn assembly. | |
| Security Horn Assembly*1 | Sounds when attempted break-in or theft is detected. | |
| Theft Warning Siren Assembly*2 | Sounds when attempted theft is detected. | |
| High Pitched Horn Assembly | Sounds when attempted theft is detected. | |
| Low Pitched Horn Assembly | Sounds when attempted theft is detected. | |
| Map Light Assembly | Intrusion Sensor (Theft Warning Ultrasonic and Tilt Sensor)*2 | Detects an unauthorized intrusion and outputs signals to the main body ECU. |
| Tilt Sensor (Theft Warning Ultrasonic and Tilt Sensor)*2 | Detects an abnormal vehicle tilt angle and outputs signals to the main body ECU. | |
| Theft Sensor Cancel Switch*2 | Outputs cancel switch ON/OFF signals to the main body ECU. | |
| Door Control Receiver (Electrical Key and TPMS Receiver Assembly)*3 | Receives a lock/unlock or power back door*5 signal from the electrical key and sends this information to the certification ECU. | |
| Smart Door Control Receiver Assembly*4 | ||
| Power Distribution Box Assembly | D DOOR UNLOCK Relay | Inputs driver door unlock request signals from the main body ECU and operates the driver door lock motor. |
| ALL DOOR UNLOCK Relay | Inputs door unlock request signals from the main body ECU and operates the door lock motors at the front passenger door and rear doors. | |
| ALL DOOR LOCK Relay | Inputs door lock request signals from the main body ECU and operates the door lock motors of all doors. | |
| DOOR BACK Relay*6 | Inputs back door open request signals from the main body ECU to operate the back door lock motor. | |
| Front Door Lock with Motor Assembly (for Driver Door)
·
Door Lock Motor
·
Door Lock Position Switch
·
Door Lock Control Switch |
·
Operates the built-in door lock motor in the forward or reverse direction under the control of the main body ECU to lock or unlock the driver door.
·
Uses the built-in door lock position switch to detect whether the driver door is locked or unlocked and outputs the result to the main body ECU.
·
Detects the condition of the built-in door lock control switch and outputs mechanical key lock/unlock request signals to the main body ECU. |
|
| Front Door Lock with Motor Assembly (for Front Passenger Door)
·
Door Lock Motor
·
Door Lock Position Switch |
·
Operates the built-in door lock motor in the forward or reverse direction under the control of the main body ECU to lock or unlock the front passenger door.
·
Uses the built-in door lock position switch to detect whether the passenger door is locked or unlocked and outputs the result to the main body ECU. |
|
| Rear Door Lock with Motor Assembly LH
·
Door Lock Motor
·
Door Lock Position Switch |
·
Operates the built-in door lock motor in the forward or reverse direction under the control of the main body ECU to lock or unlock the rear door LH.
·
Uses the built-in door lock position switch to detect whether the rear door LH is locked or unlocked and outputs the result to the main body ECU. |
|
| Rear Door Lock with Motor Assembly RH
·
Door Lock Motor
·
Door Lock Position Switch |
·
Operates the built-in door lock motor in the forward or reverse direction under the control of the main body ECU to lock or unlock the rear door RH.
·
Uses the built-in door lock position switch to detect whether the rear door RH is locked or unlocked and outputs the result to the main body ECU. |
|
| Back Door Lock with Courtesy Light Switch Assembly*5
·
Back Door Lock Motor
·
Sector Switch
·
Pawl Switch
·
Latch Switch
·
Courtesy Switch |
·
Operates the built-in back door lock motor to fully close the back door from an ajar position or open the door from a fully closed position.
·
Operates each built-in switch to detect the operating conditions of the power back door system and outputs the result to the power back door ECU.
·
Operates the built-in courtesy switch to detect whether the back door is open or closed and outputs the result to the power back door ECU. |
|
| Back Door Lock with Courtesy Light Switch Assembly*6
·
Back Door Lock Motor
·
Courtesy Switch |
·
Rotates the built-in door lock motor to lock and unlock the back door.
·
Uses the built-in door lock position switch to detect whether the back door is locked or unlocked and outputs the result to the main body ECU.
·
Outputs open/close signals for the back door to the main body ECU. |
|
| Hood Lock Assembly
·
Engine Hood Courtesy Switch |
Outputs open/close signals for the engine hood to the main body ECU. | |
| Quarter Window Assembly LH
·
Glass Breakage Sensor*2 |
Detects the glass breakage of the quarter window assembly LH and outputs this information to the main body ECU. | |
| Quarter Window Assembly RH
·
Glass Breakage Sensor*2 |
Detects the glass breakage of the quarter window assembly RH and outputs this information to the main body ECU. | |
| Back Door Glass
·
Glass Breakage Sensor*2 |
Detects the glass breakage of the back door glass and outputs this information to the main body ECU. | |
| Front Door Courtesy Light Switch Assembly (LH) | Outputs open/close signals for the front door LH to the main body ECU. | |
| Front Door Courtesy Light Switch Assembly (RH) | Outputs open/close signals for the front door RH to the main body ECU. | |
| Rear Door Courtesy Light Switch Assembly (LH) | Outputs open/close signals for the rear door LH to the main body ECU. | |
| Rear Door Courtesy Light Switch Assembly (RH) | Outputs open/close signals for the rear door RH to the main body ECU. | |
| Main Body ECU (Multiplex Network Body ECU) |
·
Controls the theft deterrent system in accordance with the signal received from the switches, sensors and ECUs.
·
Outputs lock/unlock signals to each door lock assembly to operate the door lock motor and double lock motor.
·
Outputs horn sounding request signals and outputs exterior lights, interior lights, hazard warning light flash request signals when an attempted theft is detected.
·
When an unauthorized intrusion is detected at the time of the automatic alarm watch, outputs hazard warning light operation signals to the combination meter assembly.
·
When an unauthorized intrusion is detected at the time of the automatic alarm watch, outputs sounding signals to the security horn assembly*1, theft warning siren assembly*2, high pitched horn assembly and low pitched horn assembly. |
|
| Certification ECU (Smart Key ECU Assembly) |
·
Judges and certifies the electrical key.
·
When a smart key system operation by the user is detected, sends vehicle exterior certification result signals to the main body ECU via CAN communication.
·
Sends wireless remote control signals input from the door control receiver to the main body ECU and power back door ECU*5 via CAN communication.
·
Outputs immobilizer set/unset commands.
·
Controls the security indicator light operation, power source change condition display (ACC, IG ON) and smart key indicator display.
·
Operates parts such as the IGR relay and ACC relay and controls the power source change condition.
·
Sends engine start permission signals to the ECM.
·
Outputs lock/unlock commands for the steering lock ECU. |
|
| Power Back Door ECU (Multiplex Network Door ECU)*5 |
·
Receives power back door operation request signals from the certification ECU to operate the back door lock motor.
·
Determines the operation condition of the power back door system from the ON/OFF signals of each switch built into the back door lock with courtesy light switch assembly and sends signals to the main body ECU via CAN communication. |
|
| ECM | Outputs signals such as the engine speed signal to the main body ECU. | |
| Brake Actuator Assembly
·
No. 2 Skid Control ECU |
Sends vehicle speed signals to the main body ECU via CAN communication. | |
| Combination Meter Assembly |
·
Informs the driver of the theft deterrent system status.
·
Flashes the hazard warning lights when an attempted theft is detected. |
|
| Central Gateway ECU (Network Gateway ECU) | Relays signals between the CAN communication lines. | |
| DLC3 |
·
The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions.
·
The Global TechStream (GTS) can be connected to change settings as desired by the user. |
|
FUNCTION
The theft deterrent system has the following functions:
| Function | Operation |
|---|---|
| Alarm | When the theft deterrent system switches to the alarm state, the warning items are operated and the alarm sounds for approximately 27.5 seconds. |
| Alarm Indicator | When the theft deterrent system switches to the armed preparation state or alarm state, the security indicator light is illuminated to inform the user. This indicator also serves as the immobiliser indicator, which blinks when the immobiliser is in the set state. |
| Forced Door Lock | The main body ECU transmits a door lock signal to all the doors when all of the following conditions are met:
·
The theft deterrent system is in the alarm state.
·
One of the doors has been unlocked.
·
There is no electrical key in the actuation area. The function stops when one of the following conditions is met:
·
All doors are locked.
·
The warning ends after approximately 27.5 seconds.
·
The electrical key is in the actuation area. |
SYSTEM CONTROL
The states of the theft deterrent system are as follows:
| State | Description | Theft Detection |
|---|---|---|
| Disarmed State | The theft deterrent system has not been set by the user. | Not possible |
| Armed Preparation State | This is the preparation state before the theft deterrent system becomes active (enters the armed state) when the system has been set by the user. | Not possible |
| Armed State | The theft deterrent system is active. (Theft can be detected.) | Possible |
| Alarm Sounding State | A theft attempt has been detected and the warning operation activates. | Possible |
The theft deterrent system activates as shown in the diagram above when one of the items in the following chart occurs, causing the system to enter the respective state:
The term "all doors" used in this section refers to the driver door, front passenger door, rear doors and back door.
| Condition | Item |
|---|---|
| (1) | In disarmed state 1, when the power source mode is off, the system state is switched if the following condition is met:
·
With all doors and the engine hood closed, all doors are locked by wireless operation or entry operation. |
| (2) | In disarmed state 1, when the power source mode is off, the system state is switched if any of the following condition is met:
·
With all doors closed and the engine hood open, all doors are locked by wireless operation or entry operation. |
| (3) | One of the following conditions is met:
·
The door is unlocked by operating the mechanical keys.
·
All doors are unlocked by entry operation or wireless operation.
·
Any door is unlocked.
·
Any door is opened.
·
The power switch is pushed.
·
The power source mode is turned on (ACC) or on (IG).
·
The battery is reconnected. |
| (4) | The engine hood is opened when the engine hood is closed. |
| (5) | Approximately 30 seconds elapse. |
| (6) | The engine hood close. |
| (7) | One of the following conditions is met:
·
The engine switch is turned to on and the engine is running at 550 rpm for more than approximately 2 seconds.
·
All doors are unlocked by wireless operation or entry operation. |
| (8) | One of the following conditions is met:
·
The engine hood is opened when the engine hood is closed.
·
The battery is reconnected when the engine hood is open, any door is open or any door is unlocked.
·
The intrusion sensor detects movement within the vehicle.*1
·
Theft warning tilt sensor detects a change in the pitch angle of the vehicle inclination.*1
·
The glass breakage sensor detects that glass is broken.*1
·
Any door is opened when all doors are closed.
·
Any door is unlocked when all doors are locked by wireless operation or entry operation.
·
When 5 seconds or more have elapsed after the engine switch is pressed, the power source mode is turned from off to on (IG) without pressing the engine switch.
·
The engine hood open condition continues after the warning.
·
The open condition of any door continues after the warning.
·
The power source mode on condition continues after the warning. |
| (9) | If both of the following conditions are met, the alarm stops and the system returns to armed state 1.
·
The engine hood is closed before the alarm condition.
·
After warning time of approximately 27.5 seconds + warning waiting time of approximately 5 seconds elapses. |
| (10) | One of the following conditions is met:
·
The engine hood is opened when the engine hood is closed.*2
·
The battery is reconnected when the engine hood is open*2, any door is open or any door is unlocked.
·
The intrusion sensor detects movement within the vehicle.*1
·
Theft warning tilt sensor detects a change in the pitch angle of the vehicle inclination.*1
·
The glass breakage sensor detects that glass is broken.*1
·
Any door is opened when all doors are closed.
·
Any door is unlocked when all doors are locked by wireless operation or entry operation.
·
When 5 seconds or more have elapsed after the engine switch is pressed, the power source mode is turned from off to on (IG) without pressing the engine switch.
·
The engine hood open condition continues after the warning.
·
The open condition of any door continues after the warning.
·
The power source mode on condition continues after the warning. |
| (11) | If both of the following conditions are met, the alarm stops and the system returns to armed state 2.
·
The engine hood is opened before the alarm condition.
·
After warning time of approximately 27.5 seconds + warning waiting time of approximately 5 seconds elapses. |
| (12) | One of the following conditions is met:
·
Any door is unlocked when all doors are locked.
·
Any door is opened.
·
While the power back door is closing, the power back door reverses direction, stops partway or any door other than the back door is opened.*3
·
The engine switch is pushed.
·
The power source mode is turned on (ACC) or on (IG).
·
The battery is reconnected.
·
All doors are unlocked by wireless operation or entry operation. |
| (13) | In disarmed state 1, when the power source mode is off, the system state is switched if the following condition is met:
·
While the power back door is closing and all doors are closed, all doors are locked by wireless operation or entry operation.*3 |
| (14) | Perform reservation lock via wireless operation or smart operation during power back door close operation with engine hood closed.*3 |
| (15) | Perform reservation lock via wireless operation or smart operation during power back door close operation with engine hood open.*3 |
| (16) | The engine hood is closed when the engine hood is opened. |
*1: Models with theft sensor cancel switch
*2: If closed before auto alarm set or closed during auto alarm set.
*3: Models with power back door system