FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
| Engine Stop and Start ECU | Sends either an engine stop or restart signal to the ECM according to the signals from each sensor and switch. | |
| Engine Stop and Start ECU | Backup Boost Converter |
·
Supplies battery voltage to help make up for the voltage drop that occurs when the engine is restarted, preventing the operation of various systems from being interrupted due to low battery voltage.
·
Supplies battery voltage to the oil pump with motor assembly. |
| Park/Neutral Position Switch Assembly | Detects the shift lever position and sends a signal to the engine stop and start ECU. | |
| Hood Lock Assembly | Engine Hood Courtesy Switch | Detects whether the hood is open or closed and sends a signal to the engine stop and start ECU. |
| Front Door Courtesy Light Switch Assembly (for Driver) | Detects whether the driver door is open or closed and sends a signal to the engine stop and start ECU via the main body ECU (multiplex network body ECU) via CAN communication. | |
| Front Seat Inner Belt Assembly (for Driver) | Front Seat Belt Buckle Switch (for Driver) | Detects whether or not the driver's seat belt has been fastened, and sends a signal to the engine stop and start ECU via the combination meter assembly via CAN communication. |
| Air Conditioning Amplifier Assembly | Sends an outside temperature signal and A/C switch signal to the engine stop and start ECU. | |
| Combination Meter Assembly | Stop and Start Indicator Light |
·
Turns on when the engine is stopped due to stop and start control.
·
Blinks to inform the driver that the idling stop is canceled and the engine will restart when the driver door is opened with the shift lever in D during idling stop. |
| Stop and Start Cancel Indicator Light |
·
Turns on to inform the driver that the system has been disabled when stop and start system operation is prohibited by the stop and start system cancel switch (eco run cancel switch assembly).
·
If a system malfunction is detected, the stop and start cancel indicator light blinks to inform the driver. |
|
| Multi-information Display |
·
Displays the amount of time idling stop was performed since the ignition switch was turned ON to when the ignition switch was turned off and the amount of time idling stop was performed since the reset switch was last pressed.
·
Displays the settings of the stop and start system or warning information, etc. |
|
| Stop and Start System Cancel Switch (Eco Run Cancel Switch Assembly) | Operation of the system can be canceled by pressing the stop and start system cancel switch (eco run cancel switch assembly). Pressing the switch again or turning the power source off and back on restores the operation of the system. | |
| Idle Up Switch | Send an idle up switch signal to the engine stop and start ECU. | |
| ECM |
·
Sends various information about engine conditions to the engine stop and start ECU.
·
Based on signals from the battery state sensor assembly, determines whether the battery installed on the vehicle is a specified or non-specified battery, and sends the determination result to the engine stop and start ECU. |
|
| Skid Control ECU |
·
Sends a vehicle speed signal to the engine stop and start ECU.
·
Sends a master cylinder pressure signal to the engine stop and start ECU. |
|
| Airbag ECU (Airbag ECU Assembly) | Sends airbag deployment information in the event of a collision and a deceleration signal to the engine stop and start ECU. | |
| Main Body ECU (Multiplex Network Body ECU) | Sends a front door courtesy light switch assembly (for driver) signal and front seat belt buckle switch (for driver) signal to the engine stop and start ECU. | |
| Steering Sensor | Detects the steering angle and sends signals to the engine stop and start ECU. | |
| External Backup Boost Converter (Eco Run Vehicle Converter Assembly) | Supplements the voltage drop when the engine is stopped to stabilize the audio output. | |
| Transmission Valve Body Assembly | Oil Pump with Motor Assembly | Holds the ATF pressure during idle stop. |
| ATF Temperature Sensor | Detects the ATF temperature. | |
| Battery State Sensor Assembly | Detects the battery charging and discharging amount and sends a signal to the ECM. | |
| Stop Light Switch Assembly | Detects a brake pedal released condition and sends a signal to the engine stop and start ECU via the ECM. | |
| Accelerator Pedal Sensor Assembly | Detects an accelerator pedal opening angle and sends a signal to the engine stop and start ECU via the ECM. | |
| Crankshaft Position Sensor | Detects the crankshaft angle when the engine is stopped and sends this information to the ECM. | |
| Engine Coolant Temperature Sensor | Sends the coolant temperature to the engine stop and start ECU via the ECM. | |
| Generator Assembly | Sends the generator assembly generation condition to the engine stop and start ECU via the ECM. | |
SYSTEM CONTROL
Early Stage Injection Control
Early stage injection control shortens the time it takes the engine to restart after the stop and start system stops the engine, allowing smooth initial acceleration.
The ECM memorizes the crankshaft angle detected by the crankshaft position sensor when the engine is stopped by the stop and start system.
The ECM helps shorten engine start-up time by beginning fuel injection at the appropriate cylinder based on the stored crankshaft angle when the engine restarts.
Hill-start Assist Function
The driving force (creep phenomenon) of a former A/T vehicle is regulated by depressing the brake pedal while stopped, and the driving force is transmitted by releasing the brake pedal when starting the vehicle. However, when starting a stop and start system equipped vehicle with its engine stopped due to the activation of the idle stop function, there is a short time delay before the driving force is generated as the engine will start after the brake pedal is released.
The hill-start assist function is a system to assist starting of a stop and start system equipped vehicle on a slope to deal with the situation described above, retaining the brake hydraulic pressure until sufficient driving force is generated.
The hill-start assist function operates not only on a slope but also on a level surface.
Abnormal sounds may be heard, but this does not mean the brake is malfunctioning.
The brake pedal response may change or it may vibrate, but this does not mean it is malfunctioning.
System Prohibit Control
For safety, battery protection, comfort and ECU learning reasons, the engine stop and start ECU prohibits stop and start system operation if any one of the following conditions is met.
| Prohibition Reason | Condition |
|---|---|
| Safety | If the engine is started with the hood open, such as when jump starting, engine restart operation cannot be ensured. Therefore, stop and start system operation will be prohibited. The operation of the system will be restored on the next trip. |
| If the driver door or hood is opened before the engine stops, stop and start system operation will be prohibited for safety reasons. | |
| The driver seat belt is unfastened before the engine stops. | |
| The engine catalyst is being quickly warmed up. | |
| Battery Protection | The refresh charge continues for 0.5 to 1 hour, and is carried out approximately every 30 hours of driving. While the refresh charge is occurring, stop and start system operation will be disabled. |
| When the idling stop rate becomes higher than the predetermined rate, stop and start system operation will be disabled. | |
| When the battery voltage becomes low and the battery integrated current value becomes the threshold value or less, stop and start operation will be disabled. | |
| Comfort | If the air conditioning is on when the outside temperature is high and the evaporator temperature is high, stop and start system operation will be prohibited. |
| If the air conditioning is on when the outside temperature is low, stop and start system operation will be prohibited. | |
| If the heater is on when the outside temperature is low and the engine coolant temperature is low, stop and start system operation will be prohibited. | |
| If the idle up switch, front DEF switch and blower switch are on, stop and start system operation will be prohibited. | |
| Operation | If the vehicle is stopped while the steering wheel is being operated, stop and start system operation will be prohibited. |
Warning Control
If any of the following operations are performed while the engine is stopped due to system control, the system will not restart the engine. The driver will be warned by a buzzer, or the engine will be regarded as stalled or will be restarted.
| Operation | Warning Control |
|---|---|
| The engine hood is opened | The engine stops (mode changes to "stalled", and the engine cannot be restarted until the ignition switch is turned off and then on) |
| The driver door is opened | The engine starts, warning buzzer sounds and stop and start indicator blinks. |
| The driver seat belt is unfastened | The engine starts |
Operating Conditions at Engine Stop and Restart
The engine may stop if all of these conditions are detected.
| Item | Operating Condition | |
|---|---|---|
|
*1: When the battery fluid temperature becomes -15°C (5°F) or lower or 75°C (167°F) or higher, control is prohibited. After control is prohibited and the battery fluid temperature rises to -10°C (14°F) or higher or falls to 70°C (158°F) or lower, control is performed. *2: Regarding Battery Integrated Current In the stop and start system, the engine stop and start ECU switches the system control mode (stop and start system control permitted/prohibited) based on the battery condition (charge/discharge condition) to protect the battery and to ensure stable engine restarting performance. The battery charge/discharge condition is determined from the integrated current value calculated from the battery state sensor assembly signal. The integrated current value is obtained by multiplying the current (ampere) detected by the battery state sensor assembly by the time (seconds), and is expressed in the unit A-sec. This can be measured by the Global TechStream (GTS). The engine stop and start ECU determines the power charge based on the integrated current value and prohibits stop and start system control if the value becomes the threshold or less, because the battery might not be able to start the engine. The threshold varies according to the status of battery charge control. *3: After the integrated current value becomes -19123 A-sec or less, in order to charge the battery, idling stop control is prohibited until the value becomes -17971 A-sec or more. *4: After the integrated current value becomes -1152 A-sec or less, in order to charge the battery, idling stop control is prohibited until the value becomes 0 A-sec or more. *5: V35A-FTS engine models *6: F33A-FTV engine models |
||
| Idle Stop | Engine Coolant Temperature | 40°C to 105°C (104°F to 221°F)*5 15°C to 100°C (59°F to 212°F)*6 |
| ATF Temperature | 20°C to 110°C (68°F to 230°F) | |
| Driver Door | Closed | |
| Driver Operate Brake Torque*1 | 1079 Nm or higher (changes according to gradient) | |
| Stop and Start Cancel Switch (Eco Run Cancel Switch Assembly) | Off condition | |
| Vehicle Speed | Vehicle speed changes from a constant speed to 0 km/h. | |
| Engine Speed | 1250 r/min or less | |
| Shift Lever Position | D, P | |
| Drive Mode | ECO, NORMAL or CONFORT mode is off | |
| Driver's Seat Belt | 3 seconds or more elapse after the seat belt is fastened. | |
| Engine Hood | The engine hood is closed and 3 seconds or more have elapsed. | |
| Battery Voltage | 8.2 V or higher at engine start.*5 8.22 V or higher at engine start.*6 |
|
| Battery Fluid Temperature | -10°C to 70°C (14°F to 158 °F)*1 | |
| Battery Integrated Current*2 | When the integrated current value meets any of the following conditions:
·
-17971 A-sec or more: Status of Battery Charge Control is Charge Control Coordination Mode, Stop and Start Standalone Mode, Temperature High/Low Mode or Low Temperature Mode.*3
·
0 A-sec or more: Status of Battery Charge Control is Stop and Start Restriction Mode.*4 |
|
| Air Conditioning | During "cooling down or warming up" or defrost function is not operating. | |
| ECU Learning | Completed | |
| Ambient Temperature | -5°C (23°F) or more | |
| Steering Operation | Not operated | |
| Atmospheric Pressure | Within acceptable range due to elevation, etc. | |
The engine will restart if any of these conditions are detected.
| Item | Operating Condition | |
|---|---|---|
|
*: When the shift lever is in D. |
||
| Engine Restart | Brake Torque | 959 Nm or less |
| Air Conditioning | When the air conditioning is on and a timer in the air conditioning amplifier assembly completes. | |
| When the A/C switch is on and the evaporator temperature exceeds the threshold. | ||
| Either the A/C switch, blower switch, defroster switch, pollen removal mode switch or idle-up switch is on. | ||
| Stop and Start System Cancel Switch (Eco Run Cancel Switch Assembly) | The stop and start system cancel switch (eco run cancel switch assembly) is turned on. | |
| Battery |
·
The battery voltage is 11.4 V or less.
·
The battery integrated current becomes the threshold value or less. |
|
| Driver's Door | The driver's door is opened. | |
| Driver's Seat Belt | The driver's seat belt is unfastened. | |
| Vehicle Speed | A vehicle speed signal is input. | |
| Accelerator Pedal | The accelerator pedal is depressed. | |
| Brake Pedal | The brake pedal is released.* | |
| Shift Lever | Moved from D or P position to another position. | |
| Steering Operation | The steering wheel is operated. | |
Stop and Start Priority Control
Stop and start operation time when the air conditioning is operating can be changed between "Standard" and "Extended (the stop and start system has priority)" using the steering pad switch located on the steering pad, enabling the user to select the preferred setting. However, even when selecting "Extended (the stop and start system has priority)", the idling stop time may not change depending on the vehicle condition or the surrounding environment.
Shift Lever Operation and Stop and Start Control in Different Situations
The stop and start system performs the following controls based on the shift lever operation and situation. Furthermore, the condition of the stop and start system after the shift lever is operated may change depending on the vehicle condition and surrounding environment.
DIAGNOSIS
When the engine stop and start ECU detects a malfunction and CAN communication is normal, the engine stop and start ECU records information related to the malfunction. Furthermore, the stop and start indicator light in the combination meter assembly blinks to inform the driver that CAN communication is normal.
The engine stop and start ECU also stores Diagnostic Trouble Codes (DTCs) related to malfunctions. DTCs can be read using the Global TechStream (GTS).