FUNCTION OF MAIN COMPONENTS
| Component | Function |
|---|---|
|
*1: Models with RCTA function *2: Models with RCD function *3: Models with multi-terrain monitor system *4: Models with headup display *5: Models with multimedia system (for 12.3 inch display) *6: Models with multimedia system (for 7 inch / 9 inch display) |
|
| Front Corner Ultrasonic Sensor RH/LH | Sends ultrasonic waves to detect static objects and outputs a signal to the clearance warning ECU assembly. |
| Front Center Ultrasonic Sensor RH/LH | |
| Rear Corner Ultrasonic Sensor RH/LH | |
| Rear Center Ultrasonic Sensor RH/LH | |
| Blind Spot Monitor Sensor RH/LH*1 | Sends a vehicle behind approaching detection signal to the clearance warning ECU assembly. |
| Rear Television Camera Assembly | Sends a pedestrian behind detection signal to the clearance warning ECU assembly.*2 |
| Clearance Warning ECU Assembly |
·
Receives information regarding to a static object, etc. in the vehicle traveling direction detected by the ultrasonic sensor and a vehicle approaching the driver's own vehicle from behind detected by the blind spot monitor sensor*1, and a pedestrian behind the vehicle detected by the rear television camera*2, and judges the vehicle condition based on signals from sensors, switches and ECUs located various places to perform parking support brake system control.
·
Sends a parking support brake system control signal to the ECM and No. 2 skid control ECU.
·
Sends a parking support brake system control status signal, warning request signal and malfunction judgment signal to the combination meter assembly.
·
Sends a parking support brake system warning request signal to the parking assist ECU.*3
·
Sends a parking support brake system warning request signal to the headup display.*4 |
| Combination Meter Assembly
·
PKSB OFF Indicator
·
Multi-information Display
·
Buzzer |
·
Receives a control status signal, warning request signal and combination meter assembly malfunction judgment signal from the clearance warning ECU assembly and displays a message on the multi-information display.
·
Illuminates the PKSB OFF indicator when the parking support system is off.
·
Sends a customization signal to the clearance warning ECU assembly.
·
When a malfunction is detected in the parking support brake system, the PKSB OFF indicator illuminates and a message is displayed on the multi-information display to warn the driver. |
| Multi-display Assembly*5 | Receives a warning request signal from the parking assist ECU and displays a parking support brake system warning message.*3 |
| Radio and Display Receiver Assembly*6 | |
| Headup Display (Meter Mirror Sub-assembly)*4 | Receives a warning request signal from the clearance warning ECU assembly and displays a parking support brake system warning message. |
| ECM |
·
Sends a shift position signal, accelerator pedal depression amount signal, etc. to the clearance warning ECU assembly.
·
Performs drive force suppression control in response to a parking support brake system control signal received from the clearance warning ECU assembly. |
| Brake Actuator Assembly
·
No. 2 Skid Control ECU |
·
Sends wheel speed information, a brake pedal status signal and a master cylinder pressure signal to the clearance warning ECU assembly.
·
Performs brake control in response to a parking support brake system control signal received from the clearance warning ECU assembly.
·
Sends a vehicle speed signal to the clearance warning ECU assembly. |
| Parking Assist ECU*3 | Sends a warning request signal received from the clearance warning ECU assembly to the multi-display assembly*5 or radio and display receiver assembly*6. |
| Airbag ECU (Airbag ECU Assembly)
·
Yawrate Sensor |
Sends a lateral acceleration signal, which was detected by the yawrate sensor, to the clearance warning ECU assembly. |
| Steering Sensor | Sends a steering angle signal to the clearance warning ECU assembly. |
| Air Conditioning Amplifier Assembly | Sends an outside temperature signal to the clearance warning ECU assembly. |
| Parking Support Brake Cancel Switch | Sends a parking support brake system on/off signal to the clearance warning ECU assembly. |
| Central Gateway ECU (Network Gateway ECU) | Relays the signal between the CAN communication buses. |
| DLC3 |
·
The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions.
·
The Global TechStream (GTS) can be connected to change settings as desired by the user. |
OPERATING CONDITION
Drive Force Suppression Control
When all of the following conditions are met, drive force suppression control is performed.
| Detectable Item | Condition |
|---|---|
|
*1: Except models for Australia *2: Models for Australia *3: Models with RCTA function *4: Models with RCD function |
|
| Static Objects*1/Rear Static Objects*2 |
·
Ignition switch is turned ON.
·
The parking support brake system is on.
·
A static object is in the traveling direction of the driver's own vehicle.
·
The vehicle speed is 15 km/h (9 mph) or less.
·
The driver can avoid the object by braking operations. |
| Vehicle Approaching from Rear*3 |
·
Ignition switch is turned ON.
·
The parking support brake system is on.
·
The shift position is R.
·
The vehicle speed of an approaching vehicle is 8 km/h (5 mph) or more.
·
The vehicle speed is 15 km/h (9 mph) or less.
·
An approaching vehicle may collide with the driver's own vehicle. |
| Pedestrian behind Vehicle*4 |
·
Ignition switch is turned ON.
·
The parking support brake system is on.
·
The shift position is R.
·
There is a possibility that the driver's own vehicle may collide with a pedestrian behind. |
When any of the following conditions is met, drive force suppression control is stopped.
| Detectable Item | Condition |
|---|---|
|
*1: Except models for Australia *2: Models for Australia *3: Models with RCTA function *4: Models with RCD function |
|
| Static Objects*1/Rear Static Objects*2 |
·
Ignition switch is turned off.
·
The parking support brake system is off.
·
Collision is avoided.
·
A static object moves or is moved away from the traveling direction of the driver's own vehicle. |
| Vehicle Approaching from Rear*3 |
·
Ignition switch is turned off.
·
The parking support brake system is off.
·
Collision is avoided.
·
A vehicle, which was approaching the driver's vehicle from behind, has moved away. |
| Pedestrian behind Vehicle*4 |
·
Ignition switch is turned off.
·
The parking support brake system is off.
·
Collision is avoided.
·
A pedestrian behind the vehicle has gone away. |
Brake Control
When all of the following conditions are met, brake control is performed.
| Detectable Item | Condition |
|---|---|
| All Objects |
·
Drive force suppression control is in operation.
·
Collision is difficult to avoid by braking by the driver. |
When any of the following conditions are met, brake control is stopped.
| Detectable Item | Condition |
|---|---|
|
*1: Except models for Australia *2: Models for Australia *3: Models with RCTA function *4: Models with RCD function |
|
| Static Objects*1/Rear Static Objects*2 |
·
Ignition switch is turned off.
·
The parking support brake system is off.
·
A static object moves or is moved away from the traveling direction of the driver's own vehicle.
·
The driver depresses the brake pedal after the vehicle is stopped by brake control.
·
Approximately 2 seconds have elapsed since the vehicle is stopped by brake control. |
| Vehicle Approaching from Rear*3 |
·
Ignition switch is turned off.
·
The parking support brake system is off.
·
A vehicle, which was approaching the driver's vehicle from behind, has moved away.
·
The driver depresses the brake pedal after the vehicle is stopped by brake control.
·
Approximately 2 seconds have elapsed since the vehicle is stopped by brake control. |
| Pedestrian behind Vehicle*4 |
·
Ignition switch is turned off.
·
The parking support brake system is off.
·
A pedestrian behind the vehicle has gone away.
·
The driver depresses the brake pedal after the vehicle is stopped by brake control.
·
Approximately 2 seconds have elapsed since the vehicle is stopped by brake control. |
When brake control operates, the parking support brake system automatically turns off. The system remains off until it is turned on by an operation on the multi-information display screen, the object of brake control goes away, the vehicle reverses approximately 300 mm (11.8 in.) or more*1 or approximately the entire length of the vehicle*2, the vehicle moves forward approximately the entire length of the vehicle*3, or the ignition switch is turned off and back ON.
*1: A vehicle approaching from the rear is detected.
*2: A stationary object or pedestrian who is behind the vehicle is detected.
*3: A stationary object is detected.
SYSTEM CONTROL
Parking Support Brake (Static Objects) Detection Range (Except Models for Australia)
The ultrasonic sensor detects static objects that come within approximately 4 m (13 ft.). In addition, the detection distance may differ depending on the shape of the static object.
When the vehicle is moving forward, the parking support brake (static objects) operates when all the front ultrasonic sensors detect a static object in the path of the vehicle. When the vehicle is moving forward, the parking support brake (static objects) does not operate unless two or more front ultrasonic sensors detect a static object at the same time.
When the vehicle is moving rearward, the parking support brake (static objects) operates when all the rear ultrasonic sensors detect a static object in the path of the vehicle. When the vehicle is moving rearward, the parking support brake (static objects) does not operate unless two or more rear ultrasonic sensors detect a static object at the same time.
| *a | While Driving Ahead | *b | While Reversing |
| *c | Approximately 4 m (13 ft.) | *d | Static Objects |
| *e | The detection range shown in the illustration is for when detecting an object that is 2 m (6.7 ft.) wide, 1 m (3.3 ft.) tall and is perpendicular to the ground. | - | - |
Even though the parking support brake system detects static objects, it may not operate depending on the vehicle condition.
Parking Support Brake (Rear Static Objects) Detection Range (Models for Australia)
The ultrasonic sensor detects static objects that come within approximately 4 m (13 ft.). In addition, the detection distance may differ depending on the shape of the static object.
When the vehicle is moving rearward, the parking support brake (rear static objects) operates when all the rear ultrasonic sensors detect a static object in the path of the vehicle. When the vehicle is moving rearward, the parking support brake (rear static objects) does not operate unless two or more rear ultrasonic sensors detect a static object at the same time.
| *a | While Reversing | *b | Approximately 4 m (13 ft.) |
| *c | Static Objects | *d | The detection range shown in the illustration is for when detecting an object that is 2 m (6.7 ft.) wide, 1 m (3.3 ft.) tall and is perpendicular to the ground. |
Even though the parking support brake system detects static objects, it may not operate depending on the vehicle condition.
Parking Support Brake System Control
The parking support brake system determines the state of the vehicle and its surroundings based on signals that the clearance warning ECU assembly receives from sensors, switches and ECUs installed in various locations on the vehicle, and sends the necessary control signals to ECUs to control the vehicle.
When the system operates, a warning message is displayed in the multi-information display of the combination meter assembly, headup display*1 and multi-display assembly*2 or radio and display receiver assembly*3, and the meter buzzer sounds to warn the driver.
*1: Models with headup display
*2: Models with multimedia system (for 12.3 inch display)
*3: Models with multimedia system (for 7 inch / 9 inch display)
The parking support brake system detects static objects using sensors, and when it determines that there is a risk of collision, suppress the drive force.
When the system determines that there is a high possibility of a collision even after the above operations, brake control is performed in addition to drive force suppression control.
FUNCTION
Parking Support Brake System Operation
The parking support brake cancel switch can be used to turn the parking support brake system on and off.
A PKSB OFF indicator is added to make it possible to check that the parking support brake system is off in the combination meter assembly. When the parking support brake system is off, the PKSB OFF indicator illuminates.
When the transfer position is L4, the parking support brake system turns off (does not operate) automatically. (Models with multi-terrain monitor system)
FAIL-SAFE
When the clearance warning ECU assembly detects a malfunction in the system, the system enters fail-safe mode. For details, refer to the Repair Manual.
DIAGNOSIS
In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). Refer to the Repair Manual for details.