Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2021.07
NM38G0E _51 Engine / Hybrid System _106494 F33A-FTV ENGINE CONTROL _0489393 ECD SYSTEM DE DETAILS F

F33A-FTV ENGINE CONTROL  ECD SYSTEM  DETAILS  CRANKSHAFT POSITION SENSOR  


CONSTRUCTION


a.

A Magnetic Resistance Element (MRE) type crank position sensor is used to detect the engine speed and crankshaft angle.


b.

The No. 1 crankshaft position sensor plate of the crankshaft consists of 56 teeth with 4 teeth missing. The crank position sensor outputs a crankshaft rotation signal every 6°, and the change of the signal due to the missing teeth is used to determine top-dead-center.

W149107E02
4.667,1.302 5.927,2.552 5.927,2.552 6.135,2.552 true 2.771,2.323 1.448,3.417 1.448,3.417 1.229,3.417 true 0.719,7.24 0.719,6.958 true 3.115,5.521 3.292,5.333 3.292,5.333 3.5,5.333 true 2.833,5.417 3.177,5.042 3.177,5.042 3.385,5.042 true 4.906,6.156 4.906,5.406 4.906,5.406 5.115,5.406 true 6.198,2.458 7.146,2.802 0.948,0.344 10 false Crank Position Sensor 0.156,3.344 1.24,3.854 1.083,0.51 10 false No. 1 Crankshaft Position Sensor Plate 1.042,5.323 1.479,5.521 0.438,0.198 10 false ECM 3.438,4.958 4.063,5.167 0.625,0.208 10 false 30°CA 3.542,5.25 4.167,5.458 0.625,0.208 10 false 6°CA 4.917,7.323 6.094,7.531 1.177,0.208 10 false Output Waveforms 3.74,7.031 3.99,7.271 0.25,0.24 10 false Lo 3.771,6.573 4.021,6.781 0.25,0.208 10 false Hi 0.26,7.26 1.74,7.521 1.479,0.26 10 false Crank Position Sensor 5.177,5.313 6.771,5.76 1.594,0.448 10 false No. 1 Crankshaft Position Sensor Plate (360°CA) 0.344,5.896 1.25,6.156 0.906,0.26 10 false Output Signal 1.885,7.094 3.708,7.594 1.823,0.5 10 false No. 1 Crankshaft Position Sensor Plate


c.

An MRE type crank position sensor consists of an MRE, a magnet and a sensor. The direction of the magnetic field changes due to the profile (protruding and non-protruding portions) of the No. 1 crankshaft position sensor plate, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the ECM changes to high or low. The ECM detects the crankshaft position based on this output voltage.


d.

The differences between a MRE type sensor and the pick-up coil type sensor used on the conventional models are as follows:

·

The MRE type sensor outputs a constant level of high and low digital signals regardless of the engine speed. Therefore, the MRE type sensor can detect the positions of the crankshaft.

·

The pick-up coil type sensor outputs analog signals with levels that change with the engine speed.


MRE Type and Pick-up Coil Type Output Waveform Image Comparison
W126804E01
4.292,3.083 4.292,2.667 true 4.656,1.896 4.656,1.031 4.656,1.031 4.823,1.031 true 0.01,1.125 0.938,1.417 0.927,0.292 10 false Engine Speed 3.01,1.104 3.938,1.396 0.927,0.292 10 false Engine Speed 0,2.74 0.927,3.031 0.927,0.292 10 false Sensor Output 3.021,2.438 3.948,2.729 0.927,0.292 10 false Sensor Output 2.104,3.125 2.99,3.354 0.885,0.229 10 false Digital Output 1.542,3.427 2.302,3.646 0.76,0.219 10 false MRE Type 4.76,3.469 5.729,3.688 0.969,0.219 10 false Pick-up Type 3.917,3.135 5.24,3.354 1.323,0.219 10 false Non Detection Area 6.031,2.708 7,2.948 0.969,0.24 10 false Analog Output 4.896,0.948 6.198,1.188 1.302,0.24 10 false Non Detection Area