Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2021.07
NM38G0E _51 Engine / Hybrid System _106494 F33A-FTV ENGINE CONTROL _0489393 ECD SYSTEM DE DETAILS F

F33A-FTV ENGINE CONTROL  ECD SYSTEM  DETAILS  CAMSHAFT POSITION SENSOR  


CONSTRUCTION


a.

Magneto-Resistance Element (MRE) type cam position sensors are used.


b.

To detect camshaft position, a timing rotor that is secured to the camshaft is used to generate 3 pulses for every 2 revolutions of the crankshaft. The timing rotor for camshaft is part of the camshaft.

W149108E02
0.302,2.51 0.302,2.115 0.302,2.115 0.583,2.115 true 0.99,3.344 1.198,3.344 1.198,3.344 1.979,3.823 true 1.49,5.104 1.698,5.104 1.698,5.104 2.083,4.104 true 0.177,0.948 0.813,1.167 0.635,0.219 10 false 33.9°CA 1.281,0.625 1.917,0.844 0.635,0.219 10 false 86.1°CA 2.458,1.219 3.094,1.438 0.635,0.219 10 false 63.9°CA 2.344,2.438 2.979,2.656 0.635,0.219 10 false 25.9°CA 1.156,2.823 1.792,3.042 0.635,0.219 10 false 94.1°CA 4.708,2.677 5.875,2.875 1.167,0.198 10 false Output waveforms 3.427,1.719 4.063,1.938 0.635,0.219 10 false Hi 3.438,2.271 4.073,2.49 0.635,0.219 10 false Lo 3.833,1.604 4.469,1.823 0.635,0.219 10 false 86.1°CA 4.375,2.396 5.01,2.615 0.635,0.219 10 false 63.9°CA 4.74,1.604 5.375,1.823 0.635,0.219 10 false 25.9°CA 5.146,2.396 5.781,2.615 0.635,0.219 10 false 94.1°CA 5.677,1.615 6.313,1.833 0.635,0.219 10 false 56.1°CA 6.094,2.396 6.729,2.615 0.635,0.219 10 false 33.9°CA 0.083,2.563 0.719,2.781 0.635,0.219 10 false 56.1°CA 4.417,1.042 5.99,1.292 1.573,0.25 10 false Timing Rotor (720°CA) 0.135,3.271 1.01,3.677 0.875,0.406 10 false Cam Position Sensor 0.135,5.021 1.51,5.458 1.375,0.438 10 false Intake Camshaft Sub-assembly RH


c.

An MRE type cam position sensor consists of an MRE, a magnet and a sensor. The direction of the magnetic field changes due to the profile (protruding and non-protruding portions) of the timing rotor, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the ECM changes to high or low. The ECM detects the camshaft position based on this output voltage.


d.

The differences between a MRE type sensor and the pick-up coil type sensor used on the conventional models are as follows:

·

The MRE type sensor outputs a constant level of high and low digital signals regardless of the engine speed. Therefore, the MRE type sensor can detect the positions of the camshaft at an early stage of cranking.

·

The pick-up coil type sensor outputs analog signals with levels that change with the engine speed.


MRE Type and Pick-up Coil Type Output Waveform Image Comparison
W126804E01
4.292,3.083 4.292,2.667 true 4.656,1.896 4.656,1.031 4.656,1.031 4.823,1.031 true 0.01,1.125 0.938,1.417 0.927,0.292 10 false Engine Speed 3.01,1.104 3.938,1.396 0.927,0.292 10 false Engine Speed 0,2.74 0.927,3.031 0.927,0.292 10 false Sensor Output 3.021,2.438 3.948,2.729 0.927,0.292 10 false Sensor Output 2.104,3.125 2.99,3.354 0.885,0.229 10 false Digital Output 1.542,3.427 2.302,3.646 0.76,0.219 10 false MRE Type 4.76,3.469 5.729,3.688 0.969,0.219 10 false Pick-up Type 3.917,3.135 5.24,3.354 1.323,0.219 10 false Non Detection Area 6.031,2.708 7,2.948 0.969,0.24 10 false Analog Output 4.896,0.948 6.198,1.188 1.302,0.24 10 false Non Detection Area