Home › Suspension › TIRE / WHEEL › TIRE AND WHEEL SYSTEM
RM38G0E _53 Suspension _100453 TIRE / WHEEL _0467192 TIRE AND WHEEL SYSTEM G

TIRE / WHEEL  TIRE AND WHEEL SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT TIRES

a.

Check the tires for wear and improper inflation pressure.

Cold Tire Inflation Pressure:
Tire size Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)

*1: For driving at over 160 km/h (100 mph)

245/75R17 112V 230 (2.3, 33) 230 (2.3, 33)
265/65R18 114V
265/55R20 113V 230 (2.3, 33) 230 (2.3, 33)
260 (2.6, 38)*1


NOTICE:
w/ Tire Pressure Warning System:

If the tire pressure is adjusted to the cold tire inflation pressure when the tires are warm, the tire pressure warning indicator may be on when the tires become cold.


i.

Tire pressure adjustment method when tires are warm (w/ Tire Pressure Warning System):

1.

Check tha Data List for "Tire Inflation Pressure".

2.

Adjust the "Tire Inflation Pressure" to the cold tire inflation pressure.

3.

Initialize the tire pressure warning system

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION

4.

Check tha Data List for "Temperature in Tire" (°C).

5.

Subtract the ambient temperature (°C) from the "Temperature in Tire" (°C).

6.

Adjust the tire pressure to the cold tire inflation pressure plus the subtraction above.


NOTICE:

Check the tire pressure warning system for the relationship between the inflation pressure and tire pressure warning pressure.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING




Hide 2.ROTATE TIRES

a.
C163157C13
0,0 0,0 false
V100135

Front


Remove the wheel assembly.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL>REMOVAL


b.

Rotate the tires as shown in the illustration.


c.

Install the wheel assembly.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL>INSTALLATION

HINT:

When a tire rotation is performed on a vehicle that has different specified tire pressures for the front and rear of the vehicle, it is necessary to perform initialization for the tire pressure warning system

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION



Hide 3.INSPECT WHEEL BALANCE

a.
C144019

for Steel Wheel Type:

Check and adjust the off-the-car balance.

Standard Imbalance After Adjustment:

12 g (0.0265 lb) or less


HINT:

If necessary, check and adjust the on-the-car balance.



b.
C177282C05
0.74,3.635 1.052,3.833 0.313,0.198 10 false *a 2.115,3.781 2.427,3.979 0.313,0.198 10 false *a
*a Adhesive wheel balance weight


for Aluminum Wheel Type:

Check and adjust the off-the-car balance.

Tire Size Standard Imbalance After Adjustment
265/65R18 114V 7.0 g (0.0154 lb) or less
265/55R20 113V 6.5 g (0.0143 lb) or less

NOTICE:
·

Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be attached.

·

Do not touch the adhesive surface of the tape.

·

Attach a sticking-type balance weight to the flat surface (A) shown in the illustration.

Width (A):

25 mm (0.984 in.)


·

Push the balance weight firmly so that it securely adheres to the position.

·

Do not reuse the balance weight.

·

Please use the Toyota genuine sticking type balance weight.



HINT:

If necessary, check and adjust the on-the-car balance.



c.
C137874

Using a dial indicator, check the runout of the tires.

Tire runout:

3.0 mm (0.118 in.) or less


HINT:

Remove the wheel assembly from the vehicle, and measure the wheel assembly alone.