Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › CAMSHAFT OIL CONTROL SOLENOID (for Bank 1)
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0467362 CAMSHAFT OIL CONTROL SOLENOID(for Bank 1) G

V35A-FTS ENGINE CONTROL  CAMSHAFT OIL CONTROL SOLENOID(for Bank 1)  INSPECTION  


PROCEDURE

Hide 15370B 1.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY RH (for Intake Side of Bank 1)

a.
A436353C20
1.479,0.063 1.906,0.292 0.427,0.229 0.125,0.094 0.323,0.26 0.198,0.167 10 false *a 1.552,0.115 2.01,0.313 0.458,0.198 10 false C15
*a Component without harness connected
(Cam Timing Oil Control Solenoid Assembly RH)


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C15)Location & Routing

Click Connector(C15)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Timing Oil Control Solenoid Assembly RH (Bank 1 Intake Side)

C15-1 - C15-2 0 °C (32 °F) 6.3 to 7.3 Ω
C15-1 - C15-2 20 °C (68 °F) 6.9 to 7.9 Ω
C15-1 - C15-2 40 °C (104 °F) 7.4 to 8.6 Ω


If the result is not as specified, replace the cam timing oil control solenoid assembly RH (for Intake Side of Bank 1).



b.

Stroke amount inspection

i.
A436356C01
1.198,1.344 1.583,1.344 false 1.188,2.229 1.573,2.229 false 0.125,0.333 0.438,0.49 0.313,0.156 10 false *a 0.146,2.542 0.458,2.698 0.313,0.156 10 false *b 1.021,1.281 1.333,1.438 0.313,0.156 10 false *c 1.01,2.156 1.323,2.313 0.313,0.156 10 false *c 2.25,1.208 2.563,1.365 0.313,0.156 10 false A 2.24,2.26 2.552,2.417 0.313,0.156 10 false B
*a Shaft Side Facing Down
*b Shaft Side Facing Up
*c Shaft


Using a vernier caliper, measure length (A) and (B) with the shaft of the cam timing oil control solenoid assembly RH (for Intake Side of Bank 1) set in the respective positions shown in the illustration.

NOTICE:

Do not apply battery voltage to the terminals of the cam timing oil control solenoid assembly RH (for Intake Side of Bank 1).


HINT:

If the shaft does not extend under its own weight, extend the shaft with your fingers.



ii.

Calculate the stroke amount based on the difference of length (A) and (B).

Standard:

4.3 mm (0.170 in.) or more


HINT:

Stroke amount = length (A) - length (B)


If the value is not as specified, replace the cam timing oil control solenoid assembly RH (for Intake Side of Bank 1).



Hide 15370B 2.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY RH (for Exhaust Side of Bank 1)

a.
A436353C21
1.5,0.094 1.906,0.323 0.406,0.229 0.125,0.094 0.323,0.26 0.198,0.167 10 false *a 1.583,0.135 2.042,0.333 0.458,0.198 10 false C18
*a Component without harness connected
(Cam Timing Oil Control Solenoid Assembly RH)


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C18)Location & Routing

Click Connector(C18)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Timing Oil Control Solenoid Assembly RH (Bank 1 Exhaust Side)

C18-1 - C18-2 0 °C (32 °F) 6.3 to 7.3 Ω
C18-1 - C18-2 20 °C (68 °F) 6.9 to 7.9 Ω
C18-1 - C18-2 40 °C (104 °F) 7.4 to 8.6 Ω


If the result is not as specified, replace the cam timing oil control solenoid assembly RH (for Exhaust Side of Bank 1).



b.

Stroke amount inspection

i.
A436356C01
1.198,1.344 1.583,1.344 false 1.188,2.229 1.573,2.229 false 0.125,0.333 0.438,0.49 0.313,0.156 10 false *a 0.146,2.542 0.458,2.698 0.313,0.156 10 false *b 1.021,1.281 1.333,1.438 0.313,0.156 10 false *c 1.01,2.156 1.323,2.313 0.313,0.156 10 false *c 2.25,1.208 2.563,1.365 0.313,0.156 10 false A 2.24,2.26 2.552,2.417 0.313,0.156 10 false B
*a Shaft Side Facing Down
*b Shaft Side Facing Up
*c Shaft


Using a vernier caliper, measure length (A) and (B) with the shaft of the cam timing oil control solenoid assembly RH (for Exhaust Side of Bank 1) set in the respective positions shown in the illustration.

NOTICE:

Do not apply battery voltage to the terminals of the cam timing oil control solenoid assembly RH (for Exhaust Side of Bank 1).


HINT:

If the shaft does not extend under its own weight, extend the shaft with your fingers.



ii.

Calculate the stroke amount based on the difference of length (A) and (B).

Standard:

4.3 mm (0.170 in.) or more


HINT:

Stroke amount = length (A) - length (B)


If the value is not as specified, replace the cam timing oil control solenoid assembly RH (for Exhaust Side of Bank 1).