Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › MASS AIR FLOW METER
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0467383 MASS AIR FLOW METER G

1GR-FE ENGINE CONTROL  MASS AIR FLOW METER  INSPECTION  


PROCEDURE

Hide 22204 1.INSPECT MASS AIR FLOW METER

a.
A190679C20
0.927,2.042 1.354,0.719 1.354,0.719 1.74,0.719 true 1.792,3.094 1.385,3.094 1.385,3.094 1.021,2.531 true 1.802,0.625 2.125,0.854 0.323,0.229 10 false *a 1.885,3.01 2.219,3.208 0.333,0.198 10 false *b
*a Platinum Hot Wire (Heater)
*b Temperature Sensing Element


Perform a visual check for any foreign matter on the platinum hot wire (heater) and temperature sensor (thermistor) of the mass air flow meter sub-assembly shown in the illustration.

OK:

There is no foreign matter.


If the result is not as specified, clean the mass air flow meter sub-assembly.


b.
A487339C01
1.677,2.833 1.344,2.833 true 1.563,0.823 1.229,0.823 true 1.177,2.76 1.49,2.917 0.313,0.156 10 false *a 2.073,4.333 2.385,4.49 0.313,0.156 10 false *b 1.594,0.74 1.906,0.896 0.313,0.156 10 false *c
*a Air Blow Gun
*b 10 mm (0.394 in.)
*c Airflow Hole


Clean the mass air flow meter sub-assembly.

NOTICE:
·

Do not contact the mass air flow meter sub-assembly with the nozzle of the air blow gun.

·

Do not insert the nozzle of the air blow gun into the airflow hole.



i.
A398469C01
0.125,0.125 0.365,0.302 0.24,0.177 10 false *a 1.313,0.24 1.552,0.406 0.24,0.167 10 false *b 1.563,0.573 1.792,0.74 0.229,0.167 10 false *c 0.688,0.906 0.927,1.083 0.24,0.177 10 false *d 0.677,1.708 0.917,1.885 0.24,0.177 10 false *e
*a Air Blow Duration
*b 3 to 6 Seconds
*c 1 Second
*d Air Blowing
*e Air Stopped


Using an air blow gun, clean the hole of the mass air flow meter sub-assembly by applying approximately 10 intermittent bursts of air to the airflow hole at a pressure of approximately 392 to 981 kPa (4.0 to 10.0 kgf/cm2, 57 to 142 psi).

HINT:

After performing cleaning, check the intake air temperature sensor (thermistor) resistance.




c.
A226758C13
2.406,0.802 2.813,1.021 0.406,0.219 2.771,1.458 2.521,1.833 2.521,1.833 2.229,1.833 true 2.917,1.813 2.917,1.469 true 2.823,1.844 3.188,2.042 0.365,0.198 10 false THA 2.01,1.75 2.26,1.948 0.25,0.198 10 false E2 0.031,0.031 0.219,0.26 0.188,0.229 10 false *a 2.479,0.823 2.844,1.042 0.365,0.219 10 false C71
*a Component without harness connected
(mass air flow meter)


Check the intake air temperature sensor (thermistor) resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C71)Location & Routing

Click Connector(C71)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly

C71-1 (THA) - C71-2 (E2) Always 0.47 to 19.3 kΩ


If the result is not as specified, replace the mass air flow meter.