Home › Drivetrain › JF2BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM
RM38G0E _52 Drivetrain _100437 JF2BM TRANSFER / 4WD / AWD _0467431 TRANSFER SYSTEM J

JF2BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  ECU Power Source Circuit  


WIRING DIAGRAM

C325502E26
4.74,0.865 5.198,1.063 0.458,0.198 10 false B9 4.781,0.646 5.094,0.844 0.313,0.198 10 false 8 5.083,0.875 5.396,1.073 0.313,0.198 10 false +B 4.781,1.292 4.938,1.49 0.156,0.198 10 false 3 4.688,1.5 5.146,1.698 0.458,0.198 10 false B10 5.083,1.5 5.635,1.708 0.552,0.208 10 false IGR 4.792,2.135 5.104,2.333 0.313,0.198 10 false 1 4.708,2.344 5.167,2.542 0.458,0.198 10 false B10 5.083,2.333 5.542,2.531 0.458,0.198 10 false GND 2.552,1.01 3.625,1.208 1.073,0.198 10 false 4WD-B 0.813,0.854 1.667,1.052 0.854,0.198 10 false from Battery 0.635,1.49 2.021,1.75 1.385,0.26 10 false from IG Circuit 4.896,3.083 6.646,3.292 1.75,0.208 10 false 4 Wheel Drive Control ECU 2.552,1.677 3.552,1.99 1,0.313 10 false 4WD-IGR

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (+B TERMINAL)

NG

CHECK OR REPLACE CHARGING SYSTEM OR BATTERY

2.CHECK HARNESS AND CONNECTOR (+B TERMINAL)
a.

Disconnect the B9 4 wheel drive control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B9)Location & Routing

Click Connector(B9)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

B9-8 (+B) - Body ground Always 10 to 16 V



c.

Connect the B9 4 wheel drive control ECU connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGR TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+B AND IG CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (IGR TERMINAL)
a.

Disconnect the B10 4 wheel drive control ECU connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B10)Location & Routing

Click Connector(B10)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

B10-3 (IGR) - Body ground Ignition switch ON 10 to 16 V



d.

Turn the ignition switch off.


e.

Connect the B10 4 wheel drive control ECU connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+B AND IG CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Disconnect the B10 4 wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B10)Location & Routing

Click Connector(B10)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

B10-1 (GND) - Body ground Always Below 1 Ω



c.

Connect the B10 4 wheel drive control ECU connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)