Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2021.04–2021.07
RM38G0E _58 Vehicle Interior _100612 SEAT BELT _0467501 SEAT BELT WARNING SYSTEM D

SEAT BELT  SEAT BELT WARNING SYSTEM  OPERATION CHECK  


INSPECT DRIVER SEAT BELT WARNING LIGHT (w/ Buzzer Regulated by Law)


HINT:

The seat belt warning light (in the combination meter assembly) is for both the driver seat and the passenger seat.


a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON.


c.

When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks for 6 seconds.

Check that the seat belt warning light on the combination meter assembly changes from blinking to turns off.


d.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


e.

Start the engine.


f.

Check the status of the seat belt warning light (in the combination meter assembly) under the conditions below.

i.

Check that the seat belt warning light (in the combination meter assembly) blinks when the driver seat belt is unfastened, the shift position is not in P and the parking brake is released.


ii.

Check that the seat belt warning light (in the combination meter assembly) blinks when the vehicle is driven at approximately 20 km/h or higher with the driver seat belt unfastened.

Check that after 96 seconds, the seat belt warning light (in the combination meter assembly) changes from blinking to on.


iii.

Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h or less and the shift position is changed to P.


iv.

Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h or less and the parking brake is not released.


v.

Check that the seat belt warning light (in the combination meter assembly) turns off when the driver seat belt is fastened with the seat belt warning light (in the combination meter assembly) on or blinking.




INSPECT DRIVER SEAT BELT WARNING LIGHT (w/o Buzzer Regulated by Law)


HINT:

The seat belt warning light (in the combination meter assembly) is for both the driver seat and the passenger seat.


a.

Turn the ignition switch to ON.


b.

Check that the seat belt warning light (in the combination meter assembly) turns on with the driver seat belt unfastened and under the following conditions.

i.

Shift position in P.


ii.

The parking brake is not released.



c.

Start the engine.


d.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


e.

Start the engine.


f.

Check the status of the seat belt warning light (in the combination meter assembly) under the conditions below.

i.

Check that the seat belt warning light (in the combination meter assembly) blinks when the driver seat belt is unfastened, the shift position is not in P and the parking brake is released.


ii.

Check that the seat belt warning light (in the combination meter assembly) blinks when the vehicle is driven at approximately 20 km/h or higher with the driver seat belt unfastened.

Check that after 124 seconds, the seat belt warning light (in the combination meter assembly) changes from blinking to on.


iii.

Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h or less and the shift position is changed to P.


iv.

Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h or less and the parking brake is not released.


v.

Check that the seat belt warning light (in the combination meter assembly) turns off when the driver seat belt is fastened with the seat belt warning light (in the combination meter assembly) on or blinking.




INSPECT FRONT PASSENGER SEAT BELT WARNING LIGHT (w/ Buzzer Regulated by Law)


HINT:

The seat belt warning light (in the combination meter assembly) is for both the driver seat and the passenger seat.


a.

Turn the ignition switch to ON.


b.

Fasten the driver seat belt.


c.

Check that the seat belt warning light (in the combination meter assembly) turns on with a passenger seated in the passenger seat, the passenger seat belt unfastened and under the following conditions.

i.

Shift position in P.


ii.

The parking brake is not released.



d.

When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks for 6 seconds.

Check that the seat belt warning light on the combination meter assembly changes from blinking to turns off.


e.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


f.

Start the engine.


g.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



h.

Check the status of the seat belt warning light (in the combination meter assembly) under the conditions below.

i.

Check that the seat belt warning light (in the combination meter assembly) blinks when the passenger seat belt is unfastened, the shift position is not in P and the parking brake is released.


ii.

Check that the seat belt warning light (in the combination meter assembly) blinks when the vehicle is driven at approximately 20 km/h or higher with the passenger seat belt unfastened.

Check that after 96 seconds, the seat belt warning light (in the combination meter assembly) changes from blinking to on.


iii.

Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h or less and the shift position is changed to P.


iv.

Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h or less and the parking brake is not released.


v.

Check that the seat belt warning light (in the combination meter assembly) turns off when the passenger seat belt is fastened with the seat belt warning light (in the combination meter assembly) on or blinking.




INSPECT FRONT PASSENGER SEAT BELT WARNING LIGHT (w/o Buzzer Regulated by Law)


HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

Turn the ignition switch to ON.


b.

Fasten the driver seat belt.


c.

Check that the seat belt warning light (in the combination meter assembly) turns on with a passenger seated in the passenger seat, the passenger seat belt unfastened and under the following conditions.

i.

Change the shift position to P.


ii.

The parking brake is not released.



d.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


e.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



f.

Start the engine.


g.

Check the status of the seat belt warning light (in the combination meter assembly) under the conditions below.

i.

Check that the seat belt warning light (in the combination meter assembly) blinks when the passenger seat belt is unfastened, the shift position is not in P and the parking brake is released.


ii.

Check that the seat belt warning light (in the combination meter assembly) blinks when the vehicle is driven at approximately 20 km/h or higher with the passenger seat belt unfastened.

Check that after 124 seconds, the seat belt warning light (in the combination meter assembly) changes from blinking to on.


iii.

Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h or less and the shift position is changed to P.


iv.

Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h or less and the parking brake is not released.


v.

Check that the seat belt warning light (in the combination meter assembly) turns off when the passenger seat belt is fastened with the seat belt warning light (in the combination meter assembly) on or blinking.




INSPECT REAR SEAT BELT WARNING LIGHT (w/ Rear Seat Belt Warning)


HINT:

Perform the following inspection for each rear seat.


a.
B612585C01
0.135,0.073 0.448,0.271 0.313,0.198 10 false *1
*1 Combination Meter (Rear Seat Belt Warning Light )


Turn the ignition switch off.


b.

Unfasten the rear seat belt.


c.

Open and close the rear seat right door or rear seat left door.


d.

Turn the ignition switch to ON.


e.

Check that the rear seat belt warning light (in the combination meter assembly) turns on.


f.

Check that the rear seat belt warning light turns on for approximately 66 seconds and then turns off.


g.

Fasten the rear seat belt.


h.

With the rear seat belt warning light off, check that the rear seat belt warning light in the combination meter assembly turns on again when the rear seat belt is unfastened.



INSPECT DRIVER SEAT BELT WARNING BUZZER (w/ Buzzer Regulated by Law)


HINT:

Using the GTS, check that the customization setting for the seat belt warning buzzer (in the combination meter assembly) is on.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>CUSTOMIZE PARAMETERS


a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON.


c.

After turning the ignition switch to ON, wait for approximately 1.8 seconds with the driver seat belt not fastened check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 6 seconds.


d.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


e.

Start the engine.


f.

Check that the seat belt warning buzzer (in the combination meter assembly) sounds once when the vehicle is driven at approximately 20 km/h or higher with the seat belt unfastened.


g.

After 24 seconds have passed after the buzzer sounds once, check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 6 seconds.


h.

After the buzzer has sounded intermittently at 1.2-second intervals for 6 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 90 seconds.


i.

When 96 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.


j.

Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.

Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h or higher with the seat belt unfastened.


k.

After the seat belt warning buzzer (in the combination meter assembly) stops, turn the ignition switch off and start the engine again. Check that the buzzer once again sounds intermittently when the vehicle is driven at approximately 20 km/h or higher with the seat belt unfastened.


l.

After the seat belt warning buzzer (in the combination meter assembly) stops, check that the buzzer once again sounds intermittently when the seat belt is fastened and then unfastened again, and then the vehicle is driven at approximately 20 km/h or higher.



INSPECT DRIVER SEAT BELT WARNING BUZZER (w/o Buzzer Regulated by Law)


HINT:

Using the GTS, check that the customization setting for the seat belt warning buzzer (in the combination meter assembly) is on.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>CUSTOMIZE PARAMETERS


a.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


b.

Start the engine.


c.

Check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 24 seconds when the vehicle is driven at approximately 20 km/h or higher with the seat belt unfastened.


d.

After the buzzer has sounded intermittently at 1.2-second intervals for 24 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 100 seconds.


e.

When 124 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.


f.

Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.

Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h or higher with the seat belt unfastened.


g.

After the seat belt warning buzzer (in the combination meter assembly) stops, turn the ignition switch off and start the engine again. Check that the buzzer once again sounds intermittently when the vehicle is driven at approximately 20 km/h or higher with the seat belt unfastened.


h.

After the seat belt warning buzzer (in the combination meter assembly) stops, check that the buzzer once again sounds intermittently when the seat belt is fastened and then unfastened again, and then the vehicle is driven at approximately 20 km/h or higher.



INSPECT FRONT PASSENGER SEAT BELT WARNING BUZZER (w/ Buzzer Regulated by Law)


HINT:

Using the GTS, check that the customization setting for the seat belt warning buzzer (in the combination meter assembly) is on.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>CUSTOMIZE PARAMETERS


a.

Fasten the driver seat belt.


b.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


c.

Start the engine.


d.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



e.

Check that the seat belt warning buzzer (in the combination meter assembly) sounds once when the vehicle is driven at approximately 20 km/h or higher with the seat belt unfastened.


f.

After 24 seconds have passed after the buzzer sounds once, check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 6 seconds.


g.

After the buzzer has sounded intermittently at 1.2-second intervals for 6 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 90 seconds.


h.

When 96 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.


i.

Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.

Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h or higher with the seat belt unfastened.


j.

After the seat belt warning buzzer (in the combination meter assembly) stops, turn the ignition switch off and start the engine again. Check that the buzzer once again sounds intermittently when the vehicle is driven at approximately 20 km/h or higher with the seat belt unfastened.


k.

After the seat belt warning buzzer (in the combination meter assembly) stops, check that the buzzer once again sounds intermittently when the seat belt is fastened and then unfastened again, and then the vehicle is driven at approximately 20 km/h or higher.



INSPECT FRONT PASSENGER SEAT BELT WARNING BUZZER (w/o Buzzer Regulated by Law)


HINT:

Using the GTS, check that the customization setting for the seat belt warning buzzer (in the combination meter assembly) is on.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>CUSTOMIZE PARAMETERS


a.

Fasten the driver seat belt.


b.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


c.

Start the engine.


d.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



e.

Check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 24 seconds when the vehicle is driven at approximately 20 km/h or higher with the seat belt unfastened.


f.

After the buzzer has sounded intermittently at 1.2-second intervals for 24 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 100 seconds.


g.

When 124 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.


h.

Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.

Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h or higher with the seat belt unfastened.


i.

After the seat belt warning buzzer (in the combination meter assembly) stops, turn the ignition switch off and start the engine again. Check that the buzzer once again sounds intermittently when the vehicle is driven at approximately 20 km/h or higher with the seat belt unfastened.


j.

After the seat belt warning buzzer (in the combination meter assembly) stops, check that the buzzer once again sounds intermittently when the seat belt is fastened and then unfastened again, and then the vehicle is driven at approximately 20 km/h or higher.



INSPECT REAR SEAT BELT WARNING BUZZER (w/ Buzzer Regulated by Law) (w/ Rear Seat Belt Warning)


HINT:

The seat belt warning buzzer can be customized. Make sure that this function is ON.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>CUSTOMIZE PARAMETERS


a.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


b.

Fasten the driver seat belt.


c.

Start the engine.


d.

Ensure that the rear seat belt is fastened, and then unfasten it.


e.

Check that the seat belt warning buzzer (in the combination meter assembly) sounds once when the rear seat belt is fastened and then unfastened, and then the vehicle is driven at approximately 20 km/h or higher.


f.

After 24 seconds have passed after the buzzer sounds once, check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 6 seconds.


g.

After the buzzer has sounded intermittently at 1.2-second intervals for 6 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 30 seconds.


h.

When 36 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.


i.

Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.

Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h or higher with the rear seat belt unfastened.


j.

After the seat belt warning buzzer (in the combination meter assembly) stops, turn the ignition switch off and start the engine again. Check that the buzzer once again sounds intermittently when the rear seat belt is fastened and then unfastened, and then the vehicle is driven at approximately 20 km/h or higher.


k.

After the seat belt warning buzzer (in the combination meter assembly) stops, open and close either rear door. Check that the buzzer once again sounds intermittently when the rear seat belt is fastened and then unfastened, and then the vehicle is driven at approximately 20 km/h or higher.



INSPECT REAR SEAT BELT WARNING BUZZER (w/o Buzzer Regulated by Law) (w/ Rear Seat Belt Warning)


HINT:

The seat belt warning buzzer can be customized. Make sure that this function is ON.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>CUSTOMIZE PARAMETERS


a.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


b.

Fasten the driver seat belt.


c.

Start the engine.


d.

Ensure that the rear seat belt is fastened, and then unfasten it.


e.

Check that the seat belt warning buzzer (in the combination meter assembly) sounds once when the rear seat belt is fastened and then unfastened, and then the vehicle is driven at approximately 20 km/h or higher.


f.

After the buzzer sounds once, check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 6 seconds.


g.

After the buzzer has sounded intermittently at 1.2-second intervals for 6 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 60 seconds.


h.

When 66 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.


i.

Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.

Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h or higher with the rear seat belt unfastened.


j.

After the seat belt warning buzzer (in the combination meter assembly) stops, turn the ignition switch off and start the engine again. Check that the buzzer once again sounds intermittently when the rear seat belt is fastened and then unfastened, and then the vehicle is driven at approximately 20 km/h or higher.


k.

After the seat belt warning buzzer (in the combination meter assembly) stops, open and close either rear door. Check that the buzzer once again sounds intermittently when the rear seat belt is fastened and then unfastened, and then the vehicle is driven at approximately 20 km/h or higher.