Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM38G0E _58 Vehicle Interior _100611 METER / GAUGE / DISPLAY _0467504 METER / GAUGE SYSTEM L

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  PRECAUTION  


PRECAUTION FOR REPLACING COMBINATION METER ASSEMBLY


a.

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


b.

When the combination meter assembly is replaced, update the ECU security key.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY



PRECAUTIONS


a.

When adding only a small amount of fuel (if the fuel supply analysis amount is not met), the fuel receiver gauge command value may not be updated.


b.

When adding only a small amount of fuel (if the fuel supply analysis amount is not met), the estimated distance to empty may not be updated.


c.

When adding only a small amount of fuel (if the fuel supply analysis amount is not met), the average fuel consumption after refueling may not be reset.


d.

Because there is a range in which increases and decreases in fuel cannot be detected (near the E and F points of the fuel receiver gauge command values), updating or resetting may not take place even if the fuel supply analysis amount or more is refueled.


e.

If the vehicle is stopped at an incline such as on a sloped road, the fuel receiver gauge command value may be updated.


f.

If the vehicle is stopped at an incline such as on a sloped road, the estimated distance to empty may be updated.


g.

If the vehicle is stopped at an incline such as on a sloped road, the average fuel consumption after refueling may be reset.



FUEL SUPPLY ANALYSIS CONDITIONS


a.

When a fuel increase from the fuel sender gauge input value measured after the last time the vehicle was stopped is detected to be the fuel supply analysis amount or more under any of the following conditions.

·

When the ignition switch is turned off and then to ON

·

When the ignition switch is ON with the vehicle stopped




FUEL SUPPLY ANALYSIS AMOUNT


a.

Fuel supply analysis amount for fuel receiver gauge display: 5 liters (5.3 US qts, 4.4 Imp. qts)


b.

Fuel supply analysis amount for estimated distance to empty display: 5 liters (5.3 US qts, 4.4 Imp. qts)


c.

Fuel supply analysis amount for average fuel consumption after refueling display: 10 liters (10.6 US qts, 8.8 Imp. qts)



FORCED UPDATE AND RESET


a.

Perform forced update or reset under the following conditions.

·

When the ignition switch is ON

·

A fuel increase or decrease from the fuel sender gauge input value is detected to be 15 liters (15.9 US qts, 13.2 Imp. qts) or more than the fuel receiver gauge command value for 5 minutes



b.

Items to be updated or reset

i.

Fuel receiver gauge display update


ii.

Estimated distance to empty display update


iii.

Average fuel consumption after refueling display reset




MANUAL UPDATE AND RESET


a.

Updating or resetting are possible by performing the following operation.

i.

Stop the vehicle on a level surface.


ii.

Switch the ODO/TRIP meter display to the odometer.


iii.

Turn the ignition switch off.


iv.

Perform the following procedure with the ODO/TRIP meter switching or reset switch pressed.

1.

Turn the ignition switch off and then to ON.

2.

Press and hold the ODO/TRIP meter switching or reset switch for 5 seconds to make the odometer blink.

3.

After the odometer blinks, release the ODO/TRIP meter switching or reset switch .




b.

Items to be updated or reset

i.

Fuel receiver gauge display update


ii.

Estimated distance to empty display update


iii.

Average fuel consumption after refueling display reset