Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2021.04–2021.07
RM38G0E _58 Vehicle Interior _100611 METER / GAUGE / DISPLAY _0467504 METER / GAUGE SYSTEM D

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  OPERATION CHECK  


CHECK COMBINATION METER ASSEMBLY


a.

Check speedometer operation

NOTICE:
·

The combination meter assembly receives the vehicle speed signal from the brake actuator assembly (No. 2 skid control ECU) via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the brake actuator assembly (No. 2 skid control ECU) because it is the source of the vehicle speed signal.

·

Data List values of the brake actuator assembly (No. 2 skid control ECU) are used for this inspection. Therefore, make sure to perform this inspection after confirming that DTCs are not output.



i.

Warm up the engine.


ii.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


iii.

Enter the following menus: Chassis / Brake/EPB / Data List.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed
(Vehicle speed signal output to combination meter assembly)
Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
Vehicle Speed
50003 435 36

iv.

Read the Data List according to the display on the GTS.

1.

Reference km/h:

GTS Indication (km/h) Acceptable Range (km/h)
20 21.0 to 25.0
40 42.0 to 46.0
60 63.0 to 67.0
80 84.0 to 88.0
100 104.0 to 108.0
120 125.0 to 130.0
140 146.0 to 151.0
160 167.0 to 173.0
180 187.0 to 194.0
200 208.0 to 215.0
220 229.0 to 238.0
240 249.0 to 257.0
260 270.0 to 298.0


OK:

Speedometer reading is within the acceptable range at each vehicle speed.




b.

Check tachometer

i.

Warm up the engine.


ii.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


iii.

Enter the following menus: Powertrain / Engine / Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm
for V35A-FTS:

600 to 800 rpm: Idling (shift lever in P, engine warmed up and A/C off)


for 1GR-FE:

550 to 700 rpm: Idling (shift lever in N, engine warmed up and A/C off)


-

iv.

Read the Data List according to the display on the GTS.

Reference:
GTS Indication (rpm) Acceptable Range (rpm)
Data in ( ) is for Reference
700 630 to 770
1000 (900 to 1100)
2000 (1850 to 2150)
3000 2800 to 3200
4000 (3800 to 4200)
5000 4800 to 5200
6000 (5750 to 6250)
7000* 6700 to 7300


*: for 4.2 Inch Multi-information Display


OK:

Tachometer reading is within the acceptable range at each engine speed.




c.

Check LED illumination (LED check)

i.

Check the illumination function of the warning or indicator lights listed below when turning the ignition switch to ON.

Indicator/Warning Light Switch Condition Specified Condition
Malfunction indicator lamp Ignition switch off → ON
·

Illuminates when the ignition switch is turned to ON

·

Turns off when engine started


PKSB OFF indicator light*1 Ignition switch off → ON Comes on for 3 seconds
Automatic high beam indicator light*2
Stop and start OFF indicator light*3
Brake warning light
ABS warning light
Slip indicator light
VSC OFF indicator light
Eco driving indicator light
PCS OFF warning light*4
RCTA OFF indicator light*5
BSM OFF indicator light*6
Brake hold standby indicator light
Brake hold operated indicator light
PPS warning light
SRS warning light Ignition switch off → ON Comes on for 6 seconds

*1: w/ Parking Support Brake System

*2: w/ Automatic High Beam System

*3: w/ Stop and Start System

*4: w/ Pre-collision System

*5: w/ RCTA

*6: w/ Blind Spot Monitor System