Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467506 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A413  Rear Door Electrical Antenna, Front Passenger's Side Circuit Open  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the rear door outside handle assembly (for front passenger side) (electrical key antenna) at intervals of 0.25 seconds. For the rear door outside handle assembly (for front passenger side) (electrical key antenna) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the rear door at intervals of 0.25 seconds. DTC B27A413 is stored by the certification ECU (smart key ECU assembly) when an open is detected between the certification ECU (smart key ECU assembly) and rear door outside handle assembly (for front passenger side) (electrical key antenna) (between terminals CLG4 and ANT1, or terminals CG4B and ANT2).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B27A413 Rear Door Electrical Antenna, Front Passenger's Side Circuit Open An open is detected in the circuit between the certification ECU (smart key ECU assembly) and rear door outside handle assembly (for front passenger side) (CLG4 - ANT1, CG4B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Certification ECU (smart key ECU assembly)

·

Rear door outside handle assembly (for front passenger side)

·

Harness or connector


Entry&Start A
DTC Output Confirmation Operation:

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for rear door (for front passenger side) -

Related Data List and Active Test
DTC No. Data List and Active Test
B27A413 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B510754E72
1.323,0.76 1.719,0.938 0.396,0.177 10 false ANT1 1.313,1.917 1.708,2.083 0.396,0.167 10 false ANT2 4.979,0.865 5.646,1.042 0.667,0.177 10 false I38 4.99,2.01 5.802,2.229 0.813,0.219 10 false I38 5.323,0.771 5.719,0.948 0.396,0.177 10 false CLG4 5.323,1.906 5.719,2.083 0.396,0.177 10 false CG4B 5.844,1.375 6.052,1.542 0.208,0.167 10 false IC 6.281,2.01 6.438,2.177 0.156,0.167 10 false E 6.5,2.021 6.823,2.281 0.323,0.26 10 false I39 1.771,0.771 1.896,0.938 0.125,0.167 10 false 4 1.76,1.917 1.885,2.083 0.125,0.167 10 false 6 4.99,0.667 5.208,0.844 0.219,0.177 10 false 14 5.01,1.813 5.229,1.99 0.219,0.177 10 false 13 0.552,2.729 2.833,3.292 2.281,0.563 10 false Rear Door Outside Handle Assembly (for Front Passenger Side) 0.563,2.552 2.24,2.844 1.677,0.292 10 false O8*1, P8*2 5.01,2.573 6.552,3.229 1.542,0.656 10 false Certification ECU (Smart Key ECU Assembly) 6.542,1.813 6.76,1.99 0.219,0.177 10 false 29 0.542,3.406 2.229,3.604 1.688,0.198 10 false *1: for LHD 1.708,3.406 3.396,3.604 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and rear door outside handle assembly (for front passenger side).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER SIDE))

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER SIDE))

Pre-procedure1

a.

Disconnect the I38 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the O8*1, P8*2 rear door outside handle assembly (for front passenger side) connector.

*1: for LHD

*2: for RHD



Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(I38,O8)Location & Routing

Click Connector(I38)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(O8)Body>No. 1 Rear Door Wire>Rear Door Outside Handle Assembly RH

I38-14 (CLG4) - O8-4 (ANT1) Always Below 1 Ω
I38-13 (CG4B) - O8-6 (ANT2) Always Below 1 Ω


for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(I38,P8)Location & Routing

Click Connector(I38)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(P8)Body>No. 2 Rear Door Wire>Rear Door Outside Handle Assembly LH

I38-14 (CLG4) - P8-4 (ANT1) Always Below 1 Ω
I38-13 (CG4B) - P8-6 (ANT2) Always Below 1 Ω

Result:
Proceed to
OK
NG



Post-procedure1

d.

Reconnect the I38 certification ECU (smart key ECU assembly) connector.



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO REAR DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER SIDE))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO REAR DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER SIDE))
B581656C10
4.76,0.354 5.156,0.583 0.396,0.229 3.375,0.333 3.771,0.563 0.396,0.229 3.969,2.031 3.448,1.094 false 2.917,2.031 3.354,1.094 false 4.542,2.01 4.583,1.167 false 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 4.854,0.385 5.167,0.583 0.313,0.198 10 false I39 0.76,2.604 1.073,2.802 0.313,0.198 10 false *b 4.104,2.583 4.417,2.781 0.313,0.198 10 false *c 3.844,2.073 4.375,2.323 0.531,0.25 10 false CG4B 2.75,2.063 3.281,2.313 0.531,0.25 10 false CLG4 4.531,2.042 4.823,2.25 0.292,0.208 10 false E 0.74,3.385 1.271,3.635 0.531,0.25 10 false GND 3.76,3.385 4.292,3.635 0.531,0.25 10 false GND 3.76,5.365 4.292,5.615 0.531,0.25 10 false GND 0.76,5.354 1.292,5.604 0.531,0.25 10 false GND 0.781,4.656 1.094,4.854 0.313,0.198 10 false *d 4.063,4.615 4.375,4.813 0.313,0.198 10 false *e 3.49,0.365 3.802,0.563 0.313,0.198 10 false I38
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Waveform 2 *d Waveform 3
*e Waveform 4 - -


a.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(I38,I39)Location & Routing

Click Connector(I38)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(I39)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I38-14 (CLG4) - I39-29 (E) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)
I38-14 (CLG4) - I39-29 (E) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 2)
I38-13 (CG4B) - I39-29 (E) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 3)
I38-13 (CG4B) - I39-29 (E) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 4)


*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



Result:
Proceed to
OK
NG



OK

REPLACE REAR DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER SIDE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)