Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467506 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Rear Door LH Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

If the entry lock and unlock functions do not operate for the rear door LH only, the request code may not be being transmitted from the rear door LH or the rear door outside handle assembly (for driver side) (touch sensor) may be malfunctioning. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and electrical key and tire pressure warning ECU and receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and rear door outside handle assembly (for driver side) (electrical key antenna)), or there may be wave interference.

WIRING DIAGRAM

for RHD:
B610733E12
0.323,2.708 3.219,3.26 2.896,0.552 10 false Rear Door Outside Handle Assembly LH 0.333,2.521 1.938,2.813 1.604,0.292 10 false P8 1.781,0.771 2.021,1.01 0.24,0.24 10 false 4 1.792,1.917 2.031,2.156 0.24,0.24 10 false 6 1.323,0.771 1.688,1 0.365,0.229 10 false ANT1 1.313,1.917 1.677,2.146 0.365,0.229 10 false ANT2 5.26,0.771 5.729,1.021 0.469,0.25 10 false CLG4 5.24,1.917 5.708,2.167 0.469,0.25 10 false CG4B 4.969,0.771 5.208,1.01 0.24,0.24 10 false 14 4.99,1.917 5.229,2.156 0.24,0.24 10 false 13 5.031,2.688 6.563,3.448 1.531,0.76 10 false Certification ECU (Smart Key ECU Assembly) 5.042,2.542 5.469,2.781 0.427,0.24 10 false I38 5.813,1.406 6.281,1.656 0.469,0.25 10 false IC 0.99,1.406 1.458,1.656 0.469,0.25 10 false IC

for LHD:
B610733E13
0.354,2.74 2.917,3.281 2.563,0.542 10 false Rear Door Outside Handle Assembly LH 0.354,2.573 1.906,2.802 1.552,0.229 10 false P8 1.771,0.771 2.01,1.01 0.24,0.24 10 false 4 1.781,1.917 2.021,2.156 0.24,0.24 10 false 6 1.323,0.771 1.688,1 0.365,0.229 10 false ANT1 1.323,1.917 1.688,2.146 0.365,0.229 10 false ANT2 5.25,0.771 5.719,1.021 0.469,0.25 10 false CLG3 5.26,1.917 5.729,2.167 0.469,0.25 10 false CG3B 4.979,0.771 5.219,1.01 0.24,0.24 10 false 27 4.979,1.917 5.219,2.156 0.24,0.24 10 false 26 5.104,2.719 6.646,3.292 1.542,0.573 10 false Certification ECU (Smart Key ECU Assembly) 5.094,2.573 5.521,2.813 0.427,0.24 10 false I38 5.813,1.417 6.281,1.677 0.469,0.26 10 false IC 0.99,1.396 1.458,1.656 0.469,0.26 10 false IC

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

After repair, confirm that no DTCs are output.



HINT:
·

If the rear door LH entry lock and unlock functions do not operate, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).

·

If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether the malfunction was caused by wave interference.



Body Electrical > Entry&Start > Utility
Tester Display
Vehicle Control History (RoB)
50005 440 62

PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.CHECK ENTRY OPERATION

NG

2.CHECK ENTRY OPERATION
a.

Check the operation of the entry lock and unlock functions.

i.
B581631C01
1.083,0.5 1.5,0.5 1.5,0.5 2,1.5 false 0.896,0.438 1.208,0.635 0.313,0.198 10 false *a
*a Unlock Sensor (Backside)

The illustrations shown are examples only.


Check the entry unlock function.

1.

Turn the ignition switch off.

2.

Open and close the rear door LH.

3.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.

4.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the rear door LH.

5.

Check that the LED of the electrical key transmitter sub-assembly blinks.

6.

Touch the unlock sensor on the backside of the rear door outside handle assembly LH for 2 seconds or more.*


*: Perform this step 3 seconds or more after performing step (3).


HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (1).



ii.
B581635C01
0.667,0.417 0.917,0.417 0.917,0.417 1.531,0.781 false 1.583,1 0.917,0.417 false 0.51,0.344 0.823,0.542 0.313,0.198 10 false *a
*a Lock Sensor

The illustrations shown are examples only.


Check the entry lock function.

1.

Turn the ignition switch off.

2.

Open and close the rear door LH.

3.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the rear door LH.

4.

Touch the lock sensor of the rear door outside handle assembly (groove on the rear door outside handle) with 2 or more fingers for 2 seconds or more.

HINT:
·

If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (1).

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.






Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

3.CHECK WAVE ENVIRONMENT

B

3.CHECK WAVE ENVIRONMENT
a.
B581615C01
1.781,1.094 2.01,1.344 0.229,0.25 10 false *a 1.656,1.635 1.885,1.885 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a Approximately 0.3 m (0.984 ft.)

The illustrations shown are examples only.


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the rear door outside handle assembly LH and perform an entry function check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK

HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the rear door outside handle assembly LH.

·

When the electrical key transmitter sub-assembly is brought near the rear door outside handle assembly (for driver side), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.




Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

4.READ VALUE USING GTS (REAR DRIVER SIDE UNLOCK SENSOR, REAR PASSENGER SIDE UNLOCK SENSOR)

B

AFFECTED BY WAVE INTERFERENCE

4.READ VALUE USING GTS (REAR DRIVER SIDE UNLOCK SENSOR, REAR PASSENGER SIDE UNLOCK SENSOR)
a.
B581631C01
1.083,0.5 1.5,0.5 1.5,0.5 2,1.5 false 0.896,0.438 1.208,0.635 0.313,0.198 10 false *a
*a Unlock Sensor (Backside)

The illustrations shown are examples only.


Open and close the rear door LH.


b.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.


c.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the rear door LH.


d.

Check that the LED of the electrical key transmitter sub-assembly blinks.


e.

Read the Data List according to the display on the GTS.


f.

Touch the unlock sensor on the backside of the rear door outside handle assembly LH for 2 seconds or more.*

*: Perform this step 3 seconds or more after performing step (b).


HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).


Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Driver Side Unlock Sensor Rear door LH touch sensor (unlock sensor)*1 OFF or ON OFF: Rear door LH touch sensor (unlock sensor) not touched
ON: Rear door LH touch sensor (unlock sensor) touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


Rear Passenger Side Unlock Sensor Rear door LH touch sensor (unlock sensor)*2 OFF or ON OFF: Rear door LH touch sensor (unlock sensor) not touched
ON: Rear door LH touch sensor (unlock sensor) touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


*1: for LHD

*2: for RHD


Body Electrical > Entry&Start > Data List
Tester Display
Rear Driver Side Unlock Sensor
Rear Passenger Side Unlock Sensor
50003 440 97,98
OK:

The GTS display changes correctly in response to the operation of the rear door outside handle assembly LH.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (REAR DRIVER SIDE LOCK SENSOR, REAR PASSENGER SIDE LOCK SENSOR)

NG

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)
5.READ VALUE USING GTS (REAR DRIVER SIDE LOCK SENSOR, REAR PASSENGER SIDE LOCK SENSOR)
a.
B581635C01
0.667,0.417 0.917,0.417 0.917,0.417 1.531,0.781 false 1.583,1 0.917,0.417 false 0.51,0.344 0.823,0.542 0.313,0.198 10 false *a
*a Lock Sensor

The illustrations shown are examples only.


Open and close the rear door LH.


b.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the rear door LH.


c.

Read the Data List according to the display on the GTS.


d.

Touch the lock sensor of the rear door outside handle assembly (groove on the rear door outside handle) with 2 or more fingers for 2 seconds or more.

HINT:
·

If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.



Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Driver Side Lock Sensor Rear door LH touch sensor (lock sensor)*1 OFF or ON OFF: Rear door LH touch sensor (lock sensor) not touched
ON: Rear door LH touch sensor (lock sensor) touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


Rear Passenger Side Lock Sensor Rear door LH touch sensor (lock sensor)*2 OFF or ON OFF: Rear door LH touch sensor (lock sensor) not touched
ON: Rear door LH touch sensor (lock sensor) touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


*1: for LHD

*2: for RHD


Body Electrical > Entry&Start > Data List
Tester Display
Rear Driver Side Lock Sensor
Rear Passenger Side Lock Sensor
50003 440 99,100

Result:
Result Proceed to
The GTS display does not change correctly in response to the operation of the rear door outside handle assembly LH. A
The GTS display changes correctly in response to the operation of the rear door outside handle assembly LH. B



A

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)

B

10.CHECK KEY DIAGNOSTIC MODE
6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)
a.

Disconnect the I38 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the P8 rear door outside handle assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(I38,P8)Location & Routing

Click Connector(I38)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(P8)Body>No. 2 Rear Door Wire>Rear Door Outside Handle Assembly LH

I38-27 (CLG3) - P8-4 (ANT1) Always Below 1 Ω
I38-26 (CG3B) - P8-6 (ANT2) Always Below 1 Ω
I38-27 (CLG3) or P8-4 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
I38-26 (CG3B) or P8-6 (ANT2) - Other terminals and body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(I38,P8)Location & Routing

Click Connector(I38)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(P8)Body>No. 2 Rear Door Wire>Rear Door Outside Handle Assembly LH

I38-14 (CLG4) - P8-4 (ANT1) Always Below 1 Ω
I38-13 (CG4B) - P8-6 (ANT2) Always Below 1 Ω
I38-14 (CLG4) or P8-4 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
I38-13 (CG4B) or P8-6 (ANT2) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the I38 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO REAR DOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO REAR DOOR ELECTRICAL KEY ANTENNA)
a.
B612760C01
0.344,0.667 0.656,0.865 0.313,0.198 12 false *a 0.083,1.979 0.542,2.177 0.458,0.198 10 false GND
*a Waveform 1


Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(P8)Location & Routing

Click Connector(P8)Body>No. 2 Rear Door Wire>Rear Door Outside Handle Assembly LH

P8-4 (ANT1) - P8-6 (ANT2) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)


*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Proceed to
OK
NG



OK

8.REPLACE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

8.REPLACE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH
a.

Replace the rear door outside handle assembly LH with a new one or rear door outside handle assembly RH if it is functioning properly.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

9.CHECK ENTRY OPERATION
9.CHECK ENTRY OPERATION

Result:
Result Proceed to
Entry function operates normally A
Entry function does not operate normally B



A

END (REAR DOOR OUTSIDE HANDLE ASSEMBLY LH WAS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 440 2541

b.

Select either channel 1 or channel 2 and perform key diagnostic mode inspection for each channel.

i.
B581615C01
1.781,1.094 2.01,1.344 0.229,0.25 10 false *a 1.656,1.635 1.885,1.885 0.229,0.25 10 false *1
*1 Electrical Key Transmitter Sub-assembly
*a 0.7 to 1 m (2.30 to 3.28 ft.)

The illustrations shown are examples only.


Check the electrical key antenna (for rear door LH):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the rear door outside handle assembly LH, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.





Result:
Result Proceed to
Wireless buzzer does not sound A
Wireless buzzer sounds B



A

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - REAR DOOR OUTSIDE HANDLE ASSEMBLY LH)
a.

Disconnect the I38 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the P8 rear door outside handle assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(I38,P8)Location & Routing

Click Connector(I38)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(P8)Body>No. 2 Rear Door Wire>Rear Door Outside Handle Assembly LH

I38-27 (CLG3) - P8-4 (ANT1) Always Below 1 Ω
I38-26 (CG3B) - P8-6 (ANT2) Always Below 1 Ω
I38-27 (CLG3) or P8-4 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
I38-26 (CG3B) or P8-6 (ANT2) - Other terminals and body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(I38,P8)Location & Routing

Click Connector(I38)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(P8)Body>No. 2 Rear Door Wire>Rear Door Outside Handle Assembly LH

I38-14 (CLG4) - P8-4 (ANT1) Always Below 1 Ω
I38-13 (CG4B) - P8-6 (ANT2) Always Below 1 Ω
I38-14 (CLG4) or P8-4 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
I38-13 (CG4B) or P8-6 (ANT2) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the I38 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

12.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO REAR DOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO REAR DOOR ELECTRICAL KEY ANTENNA)
a.
B612760C01
0.344,0.667 0.656,0.865 0.313,0.198 12 false *a 0.083,1.979 0.542,2.177 0.458,0.198 10 false GND
*a Waveform 1


Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(P8)Location & Routing

Click Connector(P8)Body>No. 2 Rear Door Wire>Rear Door Outside Handle Assembly LH

P8-4 (ANT1) - P8-6 (ANT2) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)


*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Proceed to
OK
NG



OK

13.CHECK ENTRY OPERATION

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

13.CHECK ENTRY OPERATION
a.

Connect all connectors and check that the function operates normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

REPLACE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)