Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467507 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  U010087  Lost Communication with ECM/PCM "A" Missing Message  U012987  Lost Communication with Brake System Control Module "A" Missing Message  U014087  Lost Communication with Body Control Module Missing Message  U015587  Lost Communication with Instrument Panel Cluster (IPC) Control Module  U111787  Lost Communication with Accessory Gateway Missing Message  


DESCRIPTION

These DTCs are stored when there is a CAN communication malfunction between the certification ECU (smart key ECU assembly) and ECM, main body ECU (multiplex network body ECU), No. 2 skid control ECU (brake actuator assembly), option connector (bus buffer ECU) or combination meter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
U010087 Lost Communication with ECM/PCM "A" Missing Message CAN communication malfunction between certification ECU (smart key ECU assembly) and ECM (1-trip detection logic*) ECM Power Source Control B
DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait at least 10 seconds.


U012987 Lost Communication with Brake System Control Module "A" Missing Message CAN communication malfunction between certification ECU (smart key ECU assembly) and No. 2 skid control ECU (brake actuator assembly) (1-trip detection logic*) No. 2 skid control ECU (brake actuator assembly) Power Source Control B
DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait at least 10 seconds.


U014087 Lost Communication with Body Control Module Missing Message CAN communication malfunction between certification ECU (smart key ECU assembly) and main body ECU (multiplex network body ECU) (1-trip detection logic*) Main body ECU (multiplex network body ECU) Power Source Control B
DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait at least 10 seconds.


U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module CAN communication malfunction between certification ECU (smart key ECU assembly) and combination meter assembly (1-trip detection logic*) Combination meter assembly Power Source Control B
DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait at least 10 seconds.


U111787 Lost Communication with Accessory Gateway Missing Message CAN communication malfunction between the certification ECU (smart key ECU assembly) and the option connector (bus buffer ECU) for approximately 10 seconds or more. Option connector (bus buffer ECU) Power Source Control B
DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait at least 10 seconds.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
DTC Code Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
U010087 There is no effect on vehicle behavior. If the following conditions are met, it can be determined that the malfunction is not in the direct line (NE) but in the CAN communication system.
·

When the engine switch is pressed, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.

·

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.


If the following conditions are met, it can be determined that there is a malfunction in both the CAN communication system and the direct line (NE).
·

When the engine switch is pressed, the engine stops cranking after 6 seconds.

·

When the engine switch is pressed and held, the engine remains cranking for up to 30 seconds.


U012987 Engine does not start. -
U014087
·

Doors cannot be locked or unlocked.

·

The warning (wireless buzzer) does not sound.


-
U015587 The warning (meter buzzer) does not sound and no warning messages displayed on the multi-information display. -
U111787 The engine cannot be started using the wireless remote control function. -

Related Data List and Active Test Items
DTC No. Data List and Active Test
U010087
U012987
U014087
U015587
U111787
-

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs and note any DTCs that are output.

Result:
Proceed to
NEXT




NEXT

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)