DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Reclining Rear | Reclining switch signal (Rearward) | ON or OFF | ON: Reclining switch (Rearward) on OFF: Reclining switch (Rearward) off |
- |
| Reclining Front | Reclining switch signal (Forward) | ON or OFF | ON: Reclining switch (Forward) on OFF: Reclining switch (Forward) off |
- |
| Front Vertical Down | Front vertical switch signal (Downward) | ON or OFF | ON: Front vertical switch (Downward) on OFF: Front vertical switch (Downward) off |
- |
| Front Vertical Up | Front vertical switch signal (Upward) | ON or OFF | ON: Front vertical switch (Upward) on OFF: Front vertical switch (Upward) off |
- |
| Lifter Switch Down | Lifter switch signal (Downward) | ON or OFF | ON: Lifter switch (Downward) on OFF: Lifter switch (Downward) off |
- |
| Lifter Switch Up | Lifter switch signal (Upward) | ON or OFF | ON: Lifter switch (Upward) on OFF: Lifter switch (Upward) off |
- |
| Slide Rear | Slide switch signal (Rearward) | ON or OFF | ON: Slide switch (Rearward) on OFF: Slide switch (Rearward) off |
- |
| Slide Front | Slide switch signal (Forward) | ON or OFF | ON: Slide switch (Forward) on OFF: Slide switch (Forward) off |
- |
| Ignition Switch | Communication state of ignition switch signal | ON or OFF | ON: Ignition switch ON OFF: Ignition switch off or ACC |
- |
| Parking Brake SW | Parking brake switch status | ON or OFF | ON: Parking brake applied OFF: Parking brake released |
- |
| Vehicle Speed | Vehicle speed data | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed | - |
| Slide Position | Seat sliding position | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Reclining Position | Seat reclining position | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Front Vertical Position | Seat front vertical position | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Lifter Position | Seat lifter position | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Lumbar Switch Front | Lumbar support adjuster switch signal (Forward) | ON or OFF | ON: Lumbar support adjuster switch (Forward) on OFF: Lumbar support adjuster switch (Forward) off |
- |
| Lumbar Switch Rear | Lumbar support adjuster switch signal (Rearward) | ON or OFF | ON: Lumbar support adjuster switch (Rearward) on OFF: Lumbar support adjuster switch (Rearward) off |
- |
| Lifter Initialize Flag | Seat lifter limit position memory | ON or OFF | ON: Memorized OFF: Not memorized |
- |
| Front Vertical Init Flag | Seat front vertical limit position memory | ON or OFF | ON: Memorized OFF: Not memorized |
- |
| Reclining Position Init Flg | Seat reclining limit position memory | ON or OFF | ON: Memorized OFF: Not memorized |
- |
| Slide Position Init Flag | Seat slide limit position memory | ON or OFF | ON: Memorized OFF: Not memorized |
- |
| Slide Position Front Limit | Seat slide limit position (front) | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Slide Position Rear Limit | Seat slide limit position (rear) | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Reclining Position Front Limit | Seat reclining limit position (front) | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Reclining Position Rear Limit | Seat reclining limit position (rear) | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Front Vertical UP Limit | Seat front vertical limit position (up) | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Front Vertical Down Limit | Seat front vertical limit position (down) | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Lifter Position UP Limit | Seat lifter limit position (up) | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Lifter Position Down Limit | Seat lifter limit position (down) | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Shift P sw(PMN) | Park state signal | Shift P or Shift Other | Shift P: Shift lever in P Shift Other: Shift lever in a position other than P |
- |
| Memory Button Buzzer Request | Driver seat buzzer request display | OFF, MOVE, REGISTRY, CANCEL, REG NG, REG WAIT | OFF: Buzzer does not sound MOVE: Request to sound buzzer when starting memory replay REGISTRY: Request to sound buzzer when starting memory registration CANCEL: Request to sound buzzer when canceling memory call registration REG NG: Request to sound buzzer when memory call registration not possible REG WAIT: Request to sound buzzer when starting memory call cabin scan |
- |
| Driver Seat Request Command | Driver seat operation request received | OFF, MEMORY, MEM MOV, MEM SOD, RET MOV, AWY MOV, AWY SOD, MEM AWY or MEM RET | OFF: No instruction MEMORY: Request to memorize MEM MOV: Request to recall memory MEM SOD: Request to replay RET MOV: Request to return AWY MOV: Request to move away AWY SOD: Request to recall away position memory MEM AWY: Request to recall memorized position of seatback MEM RET: Request to restore seatback to memorized position |
- |
| Away Move Range Scale | Seat travel distance for power easy access system | NONE, SMALL, STANDRD or LONG | NONE: Seat travel distance none SMALL: Seat travel distance short STANDRD: Seat travel distance normal LONG: Seat travel distance long |
- |
| Return Move | Return function | NOT AVL or AVAIL | NOT AVL: Not available AVAIL: Available |
- |
| Return & Away Function | Return & away function | NOT AVL or AVAIL | NOT AVL: Not available AVAIL: Available |
- |
| Driver Seat Buckle SW | Driver seat belt buckle switch | ON or OFF | ON: Driver seat belt fastened OFF: Driver seat belt unfastened |
- |
| Return Position | Return position | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| ECU Voltage Value | Voltage of position control ECU assembly | 0.95 to 20.84 V | 11 to 14 V | - |
| Battery Voltage Value | Battery voltage | 0.95 to 20.84 V | 11 to 14 V | - |
| Auto Operation Interference Avoidance Function | Setting of the function to reverse operation when jam detection is detected during slide direction driver seat | ON or OFF | Customized value displayed | - |
| Memory No1 | Seat position memorized with M1 switch | Mem or Not Mem | Mem: Memorized Not Mem: Not memorized |
- |
| Memory No2 | Seat position memorized with M2 switch | Mem or Not Mem | Mem: Memorized Not Mem: Not memorized |
- |
| Memory No3 | Seat position memorized with M3 switch | Mem or Not Mem | Mem: Memorized Not Mem: Not memorized |
- |
| Slide Position Memory No1 | Seat slide position memorized with M1 switch | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Slide Position Memory No2 | Seat slide position memorized with M2 switch | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Slide Position Memory No3 | Seat slide position memorized with M3 switch | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Reclining Position Memory No1 | Seat reclining position memorized with M1 switch | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Reclining Position Memory No2 | Seat reclining position memorized with M2 switch | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Reclining Position Memory No3 | Seat reclining position memorized with M3 switch | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Front Vertical Position Memory No1 | Front vertical position memorized with M1 switch | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Front Vertical Position Memory No2 | Front vertical position memorized with M2 switch | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Front Vertical Position Memory No3 | Front vertical position memorized with M3 switch | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Lifter Position Memory No1 | Lifter position memorized with M1 switch | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Lifter Position Memory No2 | Lifter position memorized with M2 switch | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Lifter Position Memory No3 | Lifter position memorized with M3 switch | Min: 0, Max: 65535 | Within range from 0 to 65535 | - |
| Number of Trouble Codes | Number of trouble codes | Min.: 0 or Max.: 255 | Number of DTCs will be displayed | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Courtesy Switch Status | Front door courtesy light switch assembly (RH) signal | Close or Open | Close: Front door RH closed Open: Front door RH open |
- |
| FL Door Courtesy Switch Status | Front door courtesy light switch assembly (LH) signal | Close or Open | Close: Front door LH closed Open: Front door LH open |
- |
| MEM Switch No. with Key ID 1 | Memory switch linked with key ID1 | NONE, D MEM SW1, D MEM SW2 or D MEM SW3 | NONE: No switches linked with key ID1 D MEM SW1: M1 switch linked with key ID1 D MEM SW2: M2 switch linked with key ID1 D MEM SW3: M3 switch linked with key ID1 |
- |
| MEM Switch No. with Key ID 2 | Memory switch linked with key ID2 | NONE, D MEM SW1, D MEM SW2 or D MEM SW3 | NONE: No switches linked with key ID2 D MEM SW1: M1 switch linked with key ID2 D MEM SW2: M2 switch linked with key ID2 D MEM SW3: M3 switch linked with key ID2 |
- |
| MEM Switch No. with Key ID 3 | Memory switch linked with key ID3 | NONE, D MEM SW1, D MEM SW2 or D MEM SW3 | NONE: No switches linked with key ID3 D MEM SW1: M1 switch linked with key ID3 D MEM SW2: M2 switch linked with key ID3 D MEM SW3: M3 switch linked with key ID3 |
- |
| MEM Switch No. with Key ID 4 | Memory switch linked with key ID4 | NONE, D MEM SW1, D MEM SW2 or D MEM SW3 | NONE: No switches linked with key ID4 D MEM SW1: M1 switch linked with key ID4 D MEM SW2: M2 switch linked with key ID4 D MEM SW3: M3 switch linked with key ID4 |
- |
| MEM Switch No. with Key ID 5 | Memory switch linked with key ID5 | NONE, D MEM SW1, D MEM SW2 or D MEM SW3 | NONE: No switches linked with key ID5 D MEM SW1: M1 switch linked with key ID5 D MEM SW2: M2 switch linked with key ID5 D MEM SW3: M3 switch linked with key ID5 |
- |
| MEM Switch No. with Key ID 6 | Memory switch linked with key ID6 | NONE, D MEM SW1, D MEM SW2 or D MEM SW3 | NONE: No switches linked with key ID6 D MEM SW1: M1 switch linked with key ID6 D MEM SW2: M2 switch linked with key ID6 D MEM SW3: M3 switch linked with key ID6 |
- |
| MEM Switch No. with Key ID 7 | Memory switch linked with key ID7 | NONE, D MEM SW1, D MEM SW2 or D MEM SW3 | NONE: No switches linked with key ID7 D MEM SW1: M1 switch linked with key ID7 D MEM SW2: M2 switch linked with key ID7 D MEM SW3: M3 switch linked with key ID7 |
- |
| D Seat Information | Position control ECU assembly (driver seat) status | Without, With or Return | Without: Position control ECU assembly (driver seat) not connected With: Position control ECU assembly (driver seat) connected (Not including power seat power easy access system function) Return: Position control ECU assembly (driver seat) connected (Including power seat power easy access system function) |
- |
| Driver Seat MEM_1 Memory | Seat position memorized with M1 switch | Without or With | With: Memorized Without: Not memorized |
- |
| Driver Seat MEM_2 Memory | Seat position memorized with M2 switch | Without or With | With: Memorized Without: Not memorized |
- |
| Driver Seat MEM_3 Memory | Seat position memorized with M3 switch | Without or With | With: Memorized Without: Not memorized |
- |
| Seat position/Tilt & Telesco memory recall setting | Setting of customize function "Seat position/Tilt & Telesco memory recall setting" | Driver Door or All Door | Customize setting displayed | - |
| Seat Position Voice Control Function | Status of seat position adjustment by voice recognition control.* | Disable or Enable | Customize setting displayed | - |
| Driver Seat Distance Adjust when Get Off | Setting of seat slide distance for power easy access system. | OFF, Little or Normal | Customize setting displayed | - |
| Memory Call Function | Setting of memory call function. | Disable or Enable | Customize setting displayed | - |
*: w/ Body Device Voice Recognition Function
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Seat Memory Switch1 | Seat memory switch M1 switch signal | OFF or ON | OFF: Seat memory switch M1 switch off ON: Seat memory switch M1 switch on |
- |
| Seat Memory Switch2 | Seat memory switch M2 switch signal | OFF or ON | OFF: Seat memory switch M2 switch off ON: Seat memory switch M2 switch on |
- |
| Seat Memory Switch3 | Seat memory switch M3 switch signal | OFF or ON | OFF: Seat memory switch M3 switch off ON: Seat memory switch M3 switch on |
- |
| Seat Memory Set SW | Seat memory switch SET switch signal | OFF or ON | OFF: Seat memory switch SET switch off ON: Seat memory switch SET switch on |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Seat Memory Switch1 | Seat memory switch M1 switch signal | OFF or ON | OFF: Seat memory switch M1 switch off ON: Seat memory switch M1 switch on |
- |
| Seat Memory Switch2 | Seat memory switch M2 switch signal | OFF or ON | OFF: Seat memory switch M2 switch off ON: Seat memory switch M2 switch on |
- |
| Seat Memory Switch3 | Seat memory switch M3 switch signal | OFF or ON | OFF: Seat memory switch M3 switch off ON: Seat memory switch M3 switch on |
- |
| Seat Memory Set SW | Seat memory switch SET switch signal | OFF or ON | OFF: Seat memory switch SET switch off ON: Seat memory switch SET switch on |
- |
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift SW Status (N,P Range) | Park/Neutral position switch | ON or OFF | ON: Shift lever in N or P OFF: Shift lever not in N or P |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift SW Status (N,P Range) | Park/Neutral position switch | ON or OFF | ON: Shift lever in N or P OFF: Shift lever not in N or P |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Seat Reclining | Seat reclining operation | OFF/Rear/Front | - |
| Front Vertical Operation | Seat front vertical operation | OFF/Down/Up | - |
| Lifter Operation | Seat lifter operation | OFF/Down/Up | - |
| Seat Slide Operation | Seat slide operation | OFF/Rear/Front | - |
| Buzzer | Buzzer operation | OFF/ON | - |
| Lumbar Slide | Lumbar support operation (Forward - Rearward) | OFF/Rear/Front | - |