Home › Vehicle Interior › SEAT › SEAT HEATER SYSTEM
RM38G0E _58 Vehicle Interior _100628 SEAT _0467516 SEAT HEATER SYSTEM U

SEAT  SEAT HEATER SYSTEM  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


E407961N15
1.75,0.146 2.104,0.406 0.354,0.26 2.76,0.146 3.115,0.406 0.354,0.26 3.74,0.146 4.094,0.406 0.354,0.26 4.74,0.146 5.094,0.406 0.354,0.26 5.583,0.146 5.938,0.406 0.354,0.26 1.802,0.198 2.115,0.375 0.313,0.177 10 false I30 2.823,0.198 3.219,0.406 0.396,0.208 10 false I31 3.802,0.198 4.115,0.375 0.313,0.177 10 false I32 4.792,0.198 5.104,0.375 0.313,0.177 10 false I33 5.656,0.188 6.052,0.406 0.396,0.219 10 false z16

a.

Disconnect the I33 air conditioning amplifier assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
I33-6 (IG+) - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
I33-17 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the I33 air conditioning amplifier assembly connector.


d.

Measure the voltage, resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition

*1: w/ TOYOTA Multi Operation Touch System

*2: w/ Rear Seat Heater

I31-12 (SM1R) - Body ground RH side front seat heater drive signal
·

Ignition switch ON

·

Front right side seat heater switch (multi-display*1 or air conditioning control assembly) on


Below 1 V
I31-13 (SM1L) - Body ground LH side front seat heater drive signal
·

Ignition switch ON

·

Front left side seat heater switch (multi-display*1 or air conditioning control assembly) on


Below 1 V
I30-3 (SG-7) - Body ground* Ground for rear seat heater sensor Always Below 1 Ω
I30-1 (SG-6) - Body ground Ground for front seat heater sensor Always Below 1 Ω
I30-12 (TSR) - Body ground RH side front seat heater sensor input signal - -
I30-13 (TSL) - Body ground LH side front seat heater sensor input signal - -
I30-5 (TFAR) - Body ground*2 RH side rear seat heater sensor input signal - -
I30-4 (TFAL) - Body ground*2 LH side rear seat heater sensor input signal - -
I33-7 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
I31-23 (SM2R) - Body ground*2 RH side rear seat heater drive signal
·

Ignition switch ON

·

Rear right side seat heater (rear) switch on


Below 1 V
I31-24 (SM2L) - Body ground*2 LH side rear seat heater drive signal
·

Ignition switch ON

·

Rear left side seat heater (rear) switch on


Below 1 V



CHECK AIR CONDITIONING CONTROL ASSEMBLY


a.
E459590N01
1.396,0.25 1.896,0.5 0.5,0.25 1.552,0.281 2.01,0.479 0.458,0.198 10 false I78

Disconnect the I78 air conditioning control assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No.
(Symbol)
Terminal Description Condition Specified Condition
I78-4 (E) - Body ground Ground Always Below 1 Ω
I78-7 (ACC) - Body ground Power source Ignition switch off Below 1 V
Ignition switch ACC 11 to 14 V
I78-8 (IG+) - Body ground Power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
I78-16 (+B) - Body ground Power source Always 11 to 14 V


c.

Reconnect the I78 air conditioning control assembly connector.


d.

Check for pulse according to the value(s) in the table below.

Terminal No.
(Symbol)
Terminal Description Condition Specified Condition
I78-3 (LIN1) - Body ground LIN communication signal Ignition switch ON Pulse generation



CHECK COOLER CONTROL SWITCH ASSEMBLY (w/ Rear Seat Heater)


a.
E459591N02
1.396,0.292 1.896,0.542 0.5,0.25 1.51,0.344 1.969,0.542 0.458,0.198 10 false Q52

Disconnect the Q52 cooler control switch assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No.
(Symbol)
Terminal Description Condition Specified Condition
Q52-6 (E) - Body ground Ground Always Below 1 Ω
Q52-10 (IG) - Body ground Power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


c.

Reconnect the Q52 cooler control switch assembly connector.


d.

Check for pulse according to the value(s) in the table below.

Terminal No.
(Symbol)
Terminal Description Condition Specified Condition
Q52-5 (RLIN) - Body ground LIN communication signal Ignition switch ON Pulse generation