Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM
RM38G0E _58 Vehicle Interior _100628 SEAT _0467518 REAR POWER SEAT CONTROL SYSTEM J

SEAT  REAR POWER SEAT CONTROL SYSTEM  Power Source Circuit  


DESCRIPTION

Power is supplied to the fold seat control ECU through the ECU-DCC NO. 1,RFS RH and ECU-IGR NO. 1 fuses.

WIRING DIAGRAM

C458743E01
0.417,2.5 2.01,2.833 1.594,0.333 10 false from IGR-NO. 1 Relay 0.979,1.49 1.813,1.656 0.833,0.167 10 false from Battery 0.958,0.542 1.792,0.708 0.833,0.167 10 false from Battery 2.833,2.677 4.021,2.969 1.188,0.292 10 false ECU-IGR NO. 1 2.865,0.75 4.156,1.073 1.292,0.323 10 false ECU-DCC NO. 1 3,1.656 3.885,2.052 0.885,0.396 10 false RFS RH 4.948,1.5 5.188,1.781 0.24,0.281 10 false T8 4.979,1.292 5.156,1.49 0.177,0.198 10 false 1 5.26,2.531 5.531,2.792 0.271,0.26 10 false IG 5.26,1.51 5.542,1.75 0.281,0.24 10 false +B 5.25,0.563 5.719,0.792 0.469,0.229 10 false ECUB 5.24,3.25 5.677,3.51 0.438,0.26 10 false GND 5.229,3.938 5.781,4.156 0.552,0.219 10 false GND2 4.938,5.135 6.656,5.531 1.719,0.396 10 false Fold Seat Control ECU 4.938,2.51 5.24,2.771 0.302,0.26 10 false T9 4.938,2.313 5.188,2.552 0.25,0.24 10 false 10 4.938,0.552 5.167,0.781 0.229,0.229 10 false T9 4.99,0.354 5.177,0.563 0.188,0.208 10 false 5 4.927,3.24 5.198,3.438 0.271,0.198 10 false T8 4.927,3.031 5.167,3.25 0.24,0.219 10 false 10 4.948,3.948 5.208,4.208 0.26,0.26 10 false T7 4.979,3.74 5.208,3.948 0.229,0.208 10 false 5 5.24,4.531 5.792,4.75 0.552,0.219 10 false SYSG 4.938,4.542 5.198,4.802 0.26,0.26 10 false T9 4.969,4.333 5.198,4.542 0.229,0.208 10 false 7

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU POWER SOURCE CIRCUIT)
a.

Disconnect the T7, T8 and T9 fold seat control ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(T8,T9)Location & Routing

Click Connector(T8)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Fold Seat Control ECU

Click Connector(T9)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Fold Seat Control ECU

T8-1 (+B) - Body ground Always 11 to 14 V
T9-5 (ECUB) - Body ground Always 11 to 14 V
T9-10 (IG) - Body ground Ignition switch off Below 1 V
T9-10 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T8,T7,T9)Location & Routing

Click Connector(T8)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Fold Seat Control ECU

Click Connector(T7)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Fold Seat Control ECU

Click Connector(T9)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Fold Seat Control ECU

T8-10 (GND) - Body ground Always Below 1 Ω
T7-5 (GND2) - Body ground Always Below 1 Ω
T9-7 (SYSG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR