Home › Audio / Visual / Telematics › AUDIO / VIDEO › ACTIVE NOISE CONTROL SYSTEM (for Type B)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467500 ACTIVE NOISE CONTROL SYSTEM(for Type B) J

AUDIO / VIDEO  ACTIVE NOISE CONTROL SYSTEM(for Type B)  Power Source Circuit  


DESCRIPTION

This circuit is the power source circuit for the stereo component equalizer assembly.

WIRING DIAGRAM

E462713E02
2.094,0.656 3.083,0.885 0.99,0.229 10 false from Battery*2 1.656,1.365 3.292,1.573 1.635,0.208 10 false from IGP NO.1 Relay 3.875,0.823 5.052,1.063 1.177,0.24 10 false RADIO-DCC*2 3.896,1.51 5.229,1.708 1.333,0.198 10 false ECU-IGP NO.3 3.979,2.104 4.969,2.333 0.99,0.229 10 false ECU-ACC 5.531,2.896 6.063,3.115 0.531,0.219 10 false S25 5.51,3.073 6.76,3.427 1.25,0.354 10 false Stereo Component Equalizer Assembly 5.313,0.5 5.594,0.719 0.281,0.219 10 false 15 5.333,1.219 5.615,1.438 0.281,0.219 10 false 29 5.313,1.792 5.594,2.01 0.281,0.219 10 false 14 5.323,2.333 5.604,2.552 0.281,0.219 10 false 30 5.615,0.594 5.938,0.781 0.323,0.188 10 false +B 5.594,1.333 5.927,1.552 0.333,0.219 10 false IGP 5.635,1.906 6.094,2.167 0.458,0.26 10 false ACC 5.635,2.365 6.01,2.604 0.375,0.24 10 false GND 0.698,0.24 3.229,0.469 2.531,0.229 10 false from Engine Stop and Start System*1 0.125,3.396 2.146,3.646 2.021,0.25 10 false *1: w/ Stop and Start System 2.646,3.396 4.781,3.646 2.135,0.25 10 false *2: w/o Stop and Start System 1.958,1.896 3.594,2.104 1.635,0.208 10 false from ACC Relay


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and relays for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - BATTERY [+B, ACC, IGP] AND BODY GROUND)
a.

Disconnect the S25 stereo component equalizer assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

Click Location & Routing(S25)Location & Routing

Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assembly

S25-15 (+B) - Body ground Always 11 to 14 V*1
10.5 to 16 V*2
S25-14 (ACC) - Body ground Ignition switch ACC 11 to 14 V
S25-29 (IGP) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(S25)Location & Routing

Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assembly

S25-30 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR