The television display assembly and multi-display controller are connected by GVIF cable.
When a GVIF cable error occurs between the radio receiver assembly and multi-display controller, this DTCs will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B1533 | GVIF Disconnected (from RSE to Seatback Display RH) | GVIF disconnected (from multi-display controller to television display assembly RH) |
·
Multi-display controller
·
Television display assembly RH
·
Radio receiver assembly
·
Harness or connector |
Navigation System | A |
| B1534 | GVIF Disconnected (from RSE to Seatback Display LH) | GVIF disconnected (from multi-display controller to television display assembly LH) |
·
Multi-display controller
·
Television display assembly LH
·
Radio receiver assembly
·
Harness or connector |
Navigation System | A |
| Proceed to |
|---|
| NEXT |
NEXT
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC B1533 is output. | B |
| DTC B1534 is output. | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Pre-procedure1
Disconnect the Q68 multi-display controller connector.
Disconnect the q3 television display assembly RH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(Q68,q3)Location & Routingewd_type=routing;type=c,c;code=Q68,q3 Click Connector(Q68)Seat>Floor Wire>Multi-Display Controllerewd_type=component;type=c;code=Q68;pinno=1,2,3 Click Connector(q3)Seat>Seat Audio Wire>Television Display Assembly RHewd_type=component;type=c;code=q3;pinno=1,2,3 |
||
| Q68-1 (GVI1-) - q3-1 (GVI1-) | Always | Below 1 Ω |
| Q68-2 (GVI1+) - q3-2 (GVI1+) | Always | Below 1 Ω |
| Q68-3 (GVG1) - q3-3 (GVG1) | Always | Below 1 Ω |
| Q68-1 (GVI1-) - Body ground | Always | 10 kΩ or higher |
| Q68-2 (GVI1+) - Body ground | Always | 10 kΩ or higher |
| Q68-3 (GVG1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Replace the television display assembly RH with a new or known good one.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Result | Proceed to |
|---|---|
| DTC are not output | A |
| DTCs are output | B |
A
B
Pre-procedure1
Disconnect the Q68 multi-display controller connector.
Disconnect the q6 television display assembly LH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(Q68,q6)Location & Routingewd_type=routing;type=c,c;code=Q68,q6 Click Connector(Q68)Seat>Floor Wire>Multi-Display Controllerewd_type=component;type=c;code=Q68;pinno=4,5,6 Click Connector(q6)Seat>Seat Audio Wire>Television Display Assembly LHewd_type=component;type=c;code=q6;pinno=1,2,3 |
||
| Q68-4 (GVI2-) - q6-1 (GVI1-) | Always | Below 1 Ω |
| Q68-5 (GVI2+) - q6-2 (GVI1+) | Always | Below 1 Ω |
| Q68-6 (GVG2) - q6-3 (GVG1) | Always | Below 1 Ω |
| Q68-4 (GVI2-) - Body ground | Always | 10 kΩ or higher |
| Q68-5 (GVI2+) - Body ground | Always | 10 kΩ or higher |
| Q68-6 (GVG2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Replace the television display assembly LH with a new or known good one.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Result | Proceed to |
|---|---|
| DTC are not output | A |
| DTCs are output | B |
A
B