Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467498 REAR SEAT ENTERTAINMENT SYSTEM C

AUDIO / VIDEO  REAR SEAT ENTERTAINMENT SYSTEM  B15CE  Seatback Display Disconnected  


DESCRIPTION

The television display assemblies and multi-display controller are connected via AVC-LAN communication.

This DTC will be stored if an AVC-LAN communication error occurs between the multi-display controller and a television display assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15CE Seatback Display Disconnected Seatback Display Disconnected
·

Television display assembly LH

·

Television display assembly RH

·

Multi-display controller

·

Harness or connector


Navigation System A

WIRING DIAGRAM

E384930E15
5.333,4.552 6.896,4.813 1.563,0.26 10 false Multi-display Controller 5.333,4.396 7.063,4.729 1.729,0.333 10 false Q28 3.448,4.396 5.177,4.729 1.729,0.333 10 false q1 3.438,4.552 4.583,5.021 1.146,0.469 10 false Television Display Assembly RH 3.417,2.25 4.552,2.667 1.135,0.417 10 false Television Display Assembly LH 3.438,2.073 5.167,2.406 1.729,0.333 10 false q4 5.604,1.042 6.292,1.385 0.688,0.344 10 false TX2+ 5.594,1.604 6.281,1.948 0.688,0.344 10 false TX2- 4.729,0.927 6.458,1.26 1.729,0.333 10 false 3 4.719,1.438 6.448,1.771 1.729,0.333 10 false 4 5.323,0.885 7.052,1.219 1.729,0.333 10 false 12 5.323,1.458 7.052,1.792 1.729,0.333 10 false 13 5.615,3.406 6.302,3.75 0.688,0.344 10 false TX1+ 5.604,3.969 6.292,4.313 0.688,0.344 10 false TX1- 5.302,3.25 7.031,3.583 1.729,0.333 10 false 10 5.313,3.813 7.042,4.146 1.729,0.333 10 false 11 4.74,3.24 6.469,3.573 1.729,0.333 10 false 3 4.74,3.813 6.469,4.146 1.729,0.333 10 false 4 0.615,1.031 2.01,1.458 1.396,0.427 10 false from Battery 1.844,1.229 3.24,1.656 1.396,0.427 10 false RSE DISP 3.25,1.458 4.979,1.792 1.729,0.333 10 false 10 3.323,0.958 5.052,1.292 1.729,0.333 10 false 6 3.313,3.292 5.042,3.625 1.729,0.333 10 false 6 3.26,3.865 4.99,4.198 1.729,0.333 10 false 10 0.885,5.292 3.313,5.49 2.427,0.198 10 false : AVC-LAN Communication Line 3.531,3.396 4.219,3.74 0.688,0.344 10 false +B 3.531,3.969 4.219,4.313 0.688,0.344 10 false GND4 3.531,1.583 4.219,1.927 0.688,0.344 10 false GND4 3.552,1.063 4.24,1.406 0.688,0.344 10 false +B 4.281,1.042 4.969,1.385 0.688,0.344 10 false TX1+ 4.281,1.594 4.969,1.938 0.688,0.344 10 false TX1- 4.292,3.385 4.979,3.729 0.688,0.344 10 false TX1+ 4.302,3.948 4.99,4.292 0.688,0.344 10 false TX1-

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following procedure.


PROCEDURE

1.CLEAR DTC
Body Electrical > Navigation System > Clear DTCs
50002 212
Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTC are not output A
DTCs are output B



A

B

3.CHECK OPERATION
3.CHECK OPERATION
a.

Check which television display assembly does not operate.


Result:
Result Proceed to
Television display assembly LH does not operate. A
Television display assembly RH does not operate. B



A

4.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY LH - BATTERY AND BODY GROUND)

B

9.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY RH - BATTERY AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY LH - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the q4 television display assembly LH connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(q4)Location & Routing

Click Connector(q4)Seat>Seat Audio Wire>Television Display Assembly LH

q4-10 (GND4) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(q4)Location & Routing

Click Connector(q4)Seat>Seat Audio Wire>Television Display Assembly LH

q4-6 (+B) - q4-10 (GND4) Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None.



OK

5.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - TELEVISION DISPLAY ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - TELEVISION DISPLAY ASSEMBLY LH)

Pre-procedure1

a.

Disconnect the Q28 multi-display controller connector.


b.

Disconnect the q4 television display assembly LH connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q28,q4)Location & Routing

Click Connector(Q28)Seat>Floor Wire>Multi-Display Controller

Click Connector(q4)Seat>Seat Audio Wire>Television Display Assembly LH

Q28-12 (TX2+) - q4-3 (TX1+) Always Below 1 Ω
Q28-13 (TX2-) - q4-4 (TX1-) Always Below 1 Ω
Q28-12 (TX2+) - Body ground Always 10 kΩ or higher
Q28-13 (TX2-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None.



OK

6.REPLACE TELEVISION DISPLAY ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE TELEVISION DISPLAY ASSEMBLY LH
a.

Replace the television display assembly LH.

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEVISION DISPLAY>REMOVAL



Result:
Proceed to
NEXT



NEXT

7.CLEAR DTC
7.CLEAR DTC
Body Electrical > Navigation System > Clear DTCs
50002 212
Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTC are not output A
DTCs are output B



A

END (TELEVISION DISPLAY ASSEMBLY LH IS DEFECTIVE)

B

9.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY RH - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the q1 television display assembly RH connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(q1)Location & Routing

Click Connector(q1)Seat>Seat Audio Wire>Television Display Assembly RH

q1-10 (GND4) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(q1)Location & Routing

Click Connector(q1)Seat>Seat Audio Wire>Television Display Assembly RH

q1-6 (+B) - q1-10 (GND4) Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None.



OK

10.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - TELEVISION DISPLAY ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - TELEVISION DISPLAY ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the Q28 multi-display controller connector.


b.

Disconnect the q1 television display assembly RH connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q28,q4,q1)Location & Routing

Click Connector(Q28)Seat>Floor Wire>Multi-Display Controller

Click Connector(q4)Seat>Seat Audio Wire>Television Display Assembly LH

Click Connector(q1)Seat>Seat Audio Wire>Television Display Assembly RH

Q28-10 (TX1+) - q4-3 (TX1+) Always Below 1 Ω
Q28-11 (TX1-) - q1-4 (TX1-) Always Below 1 Ω
Q28-10 (TX1+) - Body ground Always 10 kΩ or higher
Q28-11 (TX1-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None.



OK

11.REPLACE TELEVISION DISPLAY ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.REPLACE TELEVISION DISPLAY ASSEMBLY LH
a.

Replace the television display assembly RH.

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEVISION DISPLAY>REMOVAL



Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
12.CLEAR DTC
Body Electrical > Navigation System > Clear DTCs
50002 212
Result:
Proceed to
NEXT



NEXT

13.CHECK FOR DTC
13.CHECK FOR DTC
Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTC are not output A
DTCs are output B



A

END (TELEVISION DISPLAY ASSEMBLY RH IS DEFECTIVE)

B