Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467498 REAR SEAT ENTERTAINMENT SYSTEM C

AUDIO / VIDEO  REAR SEAT ENTERTAINMENT SYSTEM  B15D5  Rear Seat Entertainment System Disconnected  


DESCRIPTION

The radio receiver assembly and multi-display controller are connected via MOST communication lines.

When a MOST communication error occurs between the radio receiver assembly and multi-display controller, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15D5 Rear Seat Entertainment System Disconnected A device that is listed in the MOST network connected device record of the master unit is missing.
·

Multi-display controller

·

Radio receiver assembly

·

Harness or connector


Navigation System A

HINT:

For the MOST network, the radio receiver assembly is the master unit.


WIRING DIAGRAM

E384929E17
0.813,1.198 2.448,1.604 1.635,0.406 10 false from Battery 2.125,1.396 3.198,1.594 1.073,0.198 10 false RADIO 2.813,1.229 3.885,1.427 1.073,0.198 10 false Q29 2.833,2.813 3.906,3.01 1.073,0.198 10 false Q29 2.875,2.604 3.948,2.802 1.073,0.198 10 false 14 2.917,1.031 3.99,1.229 1.073,0.198 10 false 1 4.021,2.042 5.094,2.24 1.073,0.198 10 false Q70 5.531,3.5 6.604,3.698 1.073,0.198 10 false I139 5.542,3.656 7.156,3.906 1.615,0.25 10 false Radio Receiver Assembly 2.906,3.417 4.656,3.792 1.75,0.375 10 false Multi-display Controller 3.208,1.24 4.281,1.438 1.073,0.198 10 false +B 3.177,2.813 4.25,3.01 1.073,0.198 10 false GND 5.792,2.031 6.865,2.229 1.073,0.198 10 false MO+ 3.698,2.427 4.771,2.625 1.073,0.198 10 false MI- 3.615,2.823 4.688,3.021 1.073,0.198 10 false SLDI 5.802,2.396 6.875,2.594 1.073,0.198 10 false MO- 5.792,2.813 6.865,3.01 1.073,0.198 10 false SLDO 3.656,2.052 4.729,2.25 1.073,0.198 10 false MI+ 4.115,1.865 5.188,2.063 1.073,0.198 10 false 5 4.115,2.24 5.188,2.438 1.073,0.198 10 false 6 4.115,2.625 5.188,2.823 1.073,0.198 10 false 7 5.615,1.948 6.688,2.146 1.073,0.198 10 false 2 5.615,2.302 6.688,2.5 1.073,0.198 10 false 3 5.615,2.719 6.688,2.917 1.073,0.198 10 false 4 0.865,4.281 3.073,4.49 2.208,0.208 10 false : MOST Communication Line 4.948,2.938 6.563,3.188 1.615,0.25 10 false * 3.396,4.24 5.604,4.448 2.208,0.208 10 false *: Shielded 4.031,2.406 5.104,2.604 1.073,0.198 10 false Q70 4.021,2.792 5.094,2.99 1.073,0.198 10 false Q70

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect MOST communication.

·

This DTC may be stored when a MOST communication error occurs due to electrical noise.





A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CLEAR DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
Body Electrical > Navigation System > Clear DTCs
50002 212
Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTC are not output A
DTCs are output B



A

END (OPTIONAL COMPONENTS IS DEFECTIVE)

B

5.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - BATTERY AND BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the Q29 multi-display controller connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q29)Location & Routing

Click Connector(Q29)Seat>Floor Wire>Multi-Display Controller

Q29-14 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(Q29)Location & Routing

Click Connector(Q29)Seat>Floor Wire>Multi-Display Controller

Q29-1 (+B) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None.



OK

6.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - RADIO RECEIVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - RADIO RECEIVER ASSEMBLY)

Pre-procedure1

a.

Disconnect the Q70 multi-display controller connector.


b.

Disconnect the I139 radio receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q70,I139)Location & Routing

Click Connector(Q70)Seat>Floor Wire>Multi-Display Controller

Click Connector(I139)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Q70-5 (MI+) - I139-2 (MO+) Always Below 1 Ω
Q70-6 (MI-) - I139-3 (MO-) Always Below 1 Ω
Q70-7 (SLDI) - I139-4 (SLDO) Always Below 1 Ω
Q70-5 (MI+) - Body ground Always 10 kΩ or higher
Q70-6 (MI-) - Body ground Always 10 kΩ or higher
Q70-7 (SLDI) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None.



OK

7.REPLACE MULTI-DISPLAY CONTROLLER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE MULTI-DISPLAY CONTROLLER
a.

Replace the multi-display controller with a new or known good one.

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR SEAT ENTERTAINMENT ECU>REMOVAL



Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
Body Electrical > Navigation System > Clear DTCs
50002 212
Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTC are not output A
DTCs are output B



A

END (MULTI-DISPLAY CONTROLLER IS DEFECTIVE)

B