Home › Engine / Hybrid System › V35A-FTS (ENGINE MECHANICAL) › CYLINDER HEAD
RM38G0E _51 Engine / Hybrid System _100652 V35A-FTS ENGINE MECHANICAL _0467576 CYLINDER HEAD G

V35A-FTS ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 1110A 1.INSPECT CYLINDER HEAD SUB-ASSEMBLY

a.

Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head sub-assembly contacts the cylinder block sub-assembly and manifolds.

A475684C02
4.135,0.094 4.375,0.292 0.24,0.198 10 false *a 0.76,1.656 0.958,1.844 0.198,0.188 10 false *b 4.146,1.635 4.375,1.823 0.229,0.188 10 false *c
*a Cylinder Head Sub-assembly Lower Side *b Intake Manifold Side
*c Turbocharger Sub-assembly Side - -


Maximum Warpage
Item Specified Condition
Cylinder Head Sub-assembly Lower Side 0.05 mm (0.00197 in.)
Intake Manifold Side 0.10 mm (0.00394 in.)
Turbocharger Sub-assembly Side 0.10 mm (0.00394 in.)

If the warpage is more than the maximum, replace the cylinder head sub-assembly.


Hide 2.INSPECT CYLINDER HEAD FOR CRACKS

a.
A475685

Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.

HINT:

If cracked, replace the cylinder head sub-assembly.



Hide 13711G 3.INSPECT INTAKE VALVE

a.
A415293

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:

5.470 to 5.485 mm (0.215 to 0.216 in.)


HINT:

If the valve stem diameter is not as specified, check the intake valve guide bush oil clearance.



b.
A415294C02
0.104,1.729 0.323,1.927 0.219,0.198 10 false *a
*a Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard Margin Thickness:

1.0 mm (0.0394 in.)


Minimum Margin Thickness:

0.5 mm (0.0197 in.)


HINT:

If the margin thickness is less than the minimum, replace the intake valve.



c.
A415295C02
2.427,1 2.615,1.219 0.188,0.219 10 false *a
*a Overall Length


Using a vernier caliper, measure the overall length of the intake valve.

Standard Overall Length:

104.45 mm (4.11 in.)


Minimum Overall Length:

103.95 mm (4.09 in.)


HINT:

If the overall length is less than the minimum, replace the intake valve.



Hide 13715C 4.INSPECT EXHAUST VALVE

a.
A415296

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:

5.465 to 5.480 mm (0.215 to 0.216 in.)


HINT:

If the valve stem diameter is not as specified, check the exhaust valve guide bush oil clearance.



b.
A415297C02
0.344,1.74 0.552,1.938 0.208,0.198 10 false *a
*a Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard Margin Thickness:

1.0 mm (0.0394 in.)


Minimum Margin Thickness:

0.5 mm (0.0197 in.)


HINT:

If the margin thickness is less than the minimum, replace the exhaust valve.



c.
A415298C02
2.427,1.021 2.625,1.24 0.198,0.219 10 false *a
*a Overall Length


Using a vernier caliper, measure the overall length of the exhaust valve.

Standard Overall Length:

108.7 mm (4.28 in.)


Minimum Overall Length:

108.2 mm (4.26 in.)


HINT:

If the overall length is less than the minimum, replace the exhaust valve.



Hide 5.INSPECT INTAKE VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the intake valve seat.

NOTICE:

Do not rotate the intake valve while pressing it.



c.
A415299C02
1.427,1.229 1.615,1.427 0.188,0.198 10 false *a
*a Width


Check the valve face and intake valve seat by using the following procedure:

i.

If Prussian blue appears 360° around the entire intake valve face, the valve face is concentric.

HINT:

If the valve face is not concentric, replace the intake valve.



ii.

If Prussian blue appears 360° around the entire intake valve seat, the intake valve seat and valve face are concentric.

HINT:

If the valve face is not concentric, resurface the intake valve seat.



iii.

Measure the width of the contact area of the intake valve seat and valve face.

Standard Width:

1.1 to 1.5 mm (0.0433 to 0.0591 in.)




Hide 6.INSPECT EXHAUST VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the exhaust valve seat.

NOTICE:

Do not rotate the exhaust valve while pressing it.



c.
A415300C02
1.438,1.25 1.656,1.458 0.219,0.208 10 false *a
*a Width


Check the valve face and exhaust valve seat by using the following procedure:

i.

If Prussian blue appears 360° around the entire exhaust valve face, the valve face is concentric.

HINT:

If the valve face is not concentric, replace the exhaust valve.



ii.

If Prussian blue appears 360° around the entire exhaust valve seat, the exhaust valve seat and valve face are concentric.

HINT:

If the valve face is not concentric, resurface the exhaust valve seat.



iii.

Measure the width of the contact area of the exhaust valve seat and valve face.

Standard Width:

1.3 to 1.7 mm (0.0512 to 0.0669 in.)




Hide 13711J 7.INSPECT CYLINDER HEAD INTAKE VALVE COMPRESSION SPRING

a.
A415301

Using a vernier caliper, measure the free length of the cylinder head intake compression spring.

Standard Free Length:

53.24 mm (2.10 in.)


NOTICE:

Compression springs come in 2 different lengths. Make sure all compression springs are the same length when replacing them.



b.
A415302C02
1.896,0.01 2.104,0.208 0.208,0.198 10 false *a 0.99,1.26 1.188,1.448 0.198,0.188 10 false *b
*a Deviation
*b 40 mm (1.57 in.)


Using a steel square, measure the deviation of the cylinder head intake compression spring.

Maximum Deviation (Reference):

1.0 mm (0.0394 in.)


HINT:

If the deviation is more than the maximum, replace the cylinder head intake compression spring.



Hide 13715K 8.INSPECT CYLINDER HEAD EXHAUST VALVE COMPRESSION SPRING

a.
A415301

Using a vernier caliper, measure the free length of the cylinder head exhaust compression spring.

Standard Free Length:

57.78 mm (2.27 in.)


NOTICE:

Compression springs come in 2 different lengths. Make sure all compression springs are the same length when replacing them.



b.
A415302C02
1.896,0.01 2.104,0.208 0.208,0.198 10 false *a 0.99,1.26 1.188,1.448 0.198,0.188 10 false *b
*a Deviation
*b 40 mm (1.57 in.)


Using a steel square, measure the deviation of the cylinder head exhaust compression spring.

Maximum Deviation (Reference):

1.0 mm (0.0394 in.)


HINT:

If the deviation is more than the maximum, replace the cylinder head exhaust compression spring.



Hide 9.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A415303

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Standard Valve Guide Bush Inside Diameter:

5.510 to 5.530 mm (0.217 to 0.218 in.)



b.

Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.030 to 0.065 mm (0.00118 to 0.00256 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake 0.08 mm (0.00315 in.)
Exhaust 0.10 mm (0.00394 in.)


HINT:

If the oil clearance is more than the maximum, replace the valve and valve guide bush.