Home › Audio / Visual / Telematics › TELEMATICS › MAYDAY SWITCH
RM38G0E _56 Audio / Visual / Telematics _100608 TELEMATICS _0467767 MAYDAY SWITCH G

TELEMATICS  MAYDAY SWITCH  INSPECTION  


PROCEDURE

Hide 1.INSPECT MAYDAY SWITCH (MAP LIGHT ASSEMBLY)

a.

Measure the resistance according to the value(s) in the table below.

E461258C01
3.281,0.094 3.75,0.344 0.469,0.25 1.938,0.781 2.854,0.781 true 2.906,1 2.906,1.583 2.906,1.583 3.323,1.583 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 3.406,0.135 3.719,0.333 0.313,0.198 10 false d2 1.521,0.677 2.135,0.875 0.615,0.198 10 false GND3 3.385,1.479 4,1.677 0.615,0.198 10 false SIG1
*a Component without harness connected
(Mayday Switch (Map Light Assembly))
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(d2)Location & Routing

Click Connector(d2)Body>No. 1 Roof Wire>Map Light Assembly (Front)

d2-16 (SIG1) - d2-5 (GND3) Manual (SOS) switch not pressed 408 to 417 Ω
d2-16 (SIG1) - d2-5 (GND3) Manual (SOS) switch pressed 81 to 83 Ω


If the result is not as specified, replace the mayday switch (map light assembly).


b.

Inspect the operation (red indicator)

i.

Check that each indicator illuminates when 2 dry cell batteries are connected to the mayday switch (map light assembly) connector terminals.

E461258C02
3.323,0.073 3.698,0.302 0.375,0.229 1.927,0.771 2.854,0.771 true 3.042,1.021 3.042,1.604 3.042,1.604 3.458,1.604 true 0.01,0.031 0.271,0.229 0.26,0.198 10 false *a 3.417,0.104 3.729,0.302 0.313,0.198 10 false d2 1.51,0.677 2.125,0.875 0.615,0.198 10 false GND3 3.521,1.49 4.135,1.688 0.615,0.198 10 false IND1
*a Component without harness connected
(Mayday Switch (Map Light Assembly))
- -


NOTICE:

Do not apply more than 3 V.


OK:
Tester Connection Condition Specified Condition

Click Location & Routing(d2)Location & Routing

Click Connector(d2)Body>No. 1 Roof Wire>Map Light Assembly (Front)

d2-15 (IND1) - d2-5 (GND3) d2-15 (IND1) - Battery positive (+)
d2-5 (GND3) - Battery negative (-)
Red indicator comes on.


If the result is not as specified, replace the mayday switch (map light assembly).



c.

Inspect the operation (green indicator)

i.

Check that each indicator illuminates when 2 dry cell batteries are connected to the mayday switch (map light assembly) connector terminals.

E461258C03
3.323,0.094 3.729,0.365 0.406,0.271 1.938,0.771 2.854,0.771 true 3.031,0.833 3.031,1.5 3.031,1.5 3.448,1.5 true 0.052,0.052 0.365,0.25 0.313,0.198 10 false *a 3.417,0.135 3.729,0.333 0.313,0.198 10 false d2 1.521,0.677 2.135,0.875 0.615,0.198 10 false GND3 3.5,1.406 4.115,1.604 0.615,0.198 10 false IND2
*a Component without harness connected
(Mayday Switch (Map Light Assembly))
- -


NOTICE:

Do not apply more than 3 V.


OK:
Tester Connection Condition Specified Condition

Click Location & Routing(d2)Location & Routing

Click Connector(d2)Body>No. 1 Roof Wire>Map Light Assembly (Front)

d2-4 (IND2) - d2-5 (GND3) d2-4 (IND2) - Battery positive (+)
d2-5 (GND3) - Battery negative (-)
Green indicator comes on.


If the result is not as specified, replace the mayday switch (map light assembly).



d.

Inspect the operation (SOS indicator)

i.

Check that each indicator illuminates when the battery is connected to the mayday switch (map light assembly) connector terminals.

E462414C01
1.573,0.094 2.031,0.333 0.458,0.24 5.25,0.042 5.708,0.313 0.458,0.271 1.969,1.49 2.385,1.49 2.385,1.49 2.385,0.99 true 5.188,1.49 4.771,1.49 4.771,1.49 4.771,0.823 true 0.052,0.063 0.365,0.26 0.313,0.198 10 false *a 5.396,0.083 5.708,0.281 0.313,0.198 10 false d2 1.708,0.125 2.021,0.323 0.313,0.198 10 false d1 1.781,1.385 2.094,1.583 0.313,0.198 10 false IG 5.229,1.365 5.844,1.563 0.615,0.198 10 false GND3
*a Component without harness connected
(Mayday Switch (Map Light Assembly))
- -


OK:
Tester Connection Condition Specified Condition

Click Location & Routing(d1,d2)Location & Routing

Click Connector(d1)Body>No. 1 Roof Wire>Map Light Assembly (Front)

Click Connector(d2)Body>No. 1 Roof Wire>Map Light Assembly (Front)

d1-13 (IG) - d2-5 (GND3) d1-13 (IG) - Battery positive (+)
d2-5 (GND3) - Battery negative (-)
SOS indicator comes on.


If the result is not as specified, replace the mayday switch (map light assembly).