Home › Vehicle Interior › LIGHTING (INT) › BACK DOOR COURTESY SWITCH
RM38G0E _58 Vehicle Interior _100749 LIGHTING (INT) _0467859 BACK DOOR COURTESY SWITCH G

LIGHTING (INT)  BACK DOOR COURTESY SWITCH  INSPECTION  


PROCEDURE

Hide 69350P 1.INSPECT BACK DOOR LOCK ASSEMBLY WITH COURTESY LIGHT SWITCH (w/o Power Back Door)

a.
E407983C04
1.625,3.375 1.927,3.563 0.302,0.188 1.479,1.198 0.875,1.198 true 1.458,2.948 0.885,2.948 true 1.333,4.417 1.583,4 true 2.25,4.417 1.979,4.01 true 1.792,4.427 1.792,4.01 true 0.354,2.24 0.667,2.438 0.313,0.198 10 false *a 1.073,3.625 1.385,3.823 0.313,0.198 10 false *c 0.375,0.125 0.688,0.323 0.313,0.198 10 false *b 1.25,4.417 1.5,4.615 0.25,0.198 10 false + 1.635,4.417 2.25,4.615 0.615,0.198 10 false ACT- 2.135,4.417 2.75,4.615 0.615,0.198 10 false ACT+ 0.615,2.875 0.927,3.073 0.313,0.198 10 false *1 0.656,1.125 0.969,1.323 0.313,0.198 10 false *1 1.708,3.365 2.021,3.563 0.313,0.198 10 false g4
*1 Latch
*a Open
*b Close
*c Component without harness connected
(Back Door Lock Assembly with Courtesy Light Switch)


Check the operation of the door lock motor.

i.

Move the back door lock with courtesy light switch assembly to the close position.


ii.

Apply battery voltage to the door lock motor assembly and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → g4-1 (ACT+)
Battery negative (-) → g4-2 (ACT-)
Close → Open


If the result is not as specified, replace the back door lock assembly with courtesy light switch.



b.

Check the operation of the door courtesy switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(g4)Location & Routing

Click Connector(g4)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

g4-2 (ACT-) - g4-3 (+) Close 10 kΩ or higher
Open Below 1 Ω


If the result is not as specified, replace the back door lock assembly with courtesy light switch.



Hide 69350P 2.INSPECT BACK DOOR LOCK ASSEMBLY WITH COURTESY LIGHT SWITCH (w/ Power Back Door)

a.
E407984C06
1.542,2.146 1.875,2.385 0.333,0.24 0.917,2.833 1.5,2.833 true 1.917,2.833 2.5,2.833 true 0.948,0.917 1.177,1.125 0.229,0.208 10 true *b 1.688,0.917 1.917,1.125 0.229,0.208 10 true *c 0.958,2.375 1.188,2.583 0.229,0.208 10 false *a 1.771,1.917 2,2.125 0.229,0.208 10 true *b 0.938,1.917 1.167,2.125 0.229,0.208 10 true *c 0.604,2.75 0.833,2.958 0.229,0.208 10 false M+ 2.583,2.75 2.813,2.958 0.229,0.208 10 false M- 1.635,2.167 1.948,2.365 0.313,0.198 10 false g5
*a Component without harness connected
(Back Door Lock Assembly with Courtesy Light Switch)
*b Close Operation Direction
*c Open Operation Direction


Check the operation.

i.

Apply battery voltage and check the operation of the closer motor.

OK:
Battery Connection Result
Battery positive (+) - g5-1 (M-)
Battery negative (-) - g5-2 (M+)
Open operation
Battery positive (+) - g5-2 (M+)
Battery negative (-) - g5-1 (M-)
Close operation


If the result is not as specified, replace the back door lock assembly with courtesy light switch.



b.
E407985C11
1.479,1.948 1.833,2.177 0.354,0.229 1.052,2.708 1.479,2.708 true 1.927,2.698 2.354,2.698 true 1.979,0.51 2.083,0.25 2.083,0.25 2.417,0.25 true 2.104,0.302 2.417,0.5 0.313,0.198 10 false *e 1.771,0.219 2.083,0.417 0.313,0.198 10 false *d 1.021,0.25 1.333,0.448 0.313,0.198 10 false *c 0.438,0.802 0.75,1 0.313,0.198 10 false *b 2.427,2.625 2.885,2.823 0.458,0.198 10 false CLS 0.823,2.635 1.281,2.833 0.458,0.198 10 false E 0.583,0.5 1.5,0.698 0.917,0.198 10 false 37°26' 1.333,0.25 2.25,0.448 0.917,0.198 10 false 37°23' 2.5,0.167 3.417,0.365 0.917,0.198 10 false 13°43' 0.74,1.854 1.052,2.052 0.313,0.198 10 false *a 1.583,1.969 1.896,2.167 0.313,0.198 10 false g6
*a Component without harness connected
(Back Door Lock Assembly with Courtesy Light Switch)
*b Open Position
*c Half-latch Position
*d Full-latch Position
*e Overstroke Position


Check the resistance of the half latch switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g6)Location & Routing

Click Connector(g6)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

g6-1 (E) - g6-3 (CLS) Open position Below 1 Ω
Open position → Half-latch position Below 1 Ω → 10 kΩ or higher
Half-latch position 10 kΩ or higher
Full-latch position
Overstroke position


If the result is not as specified, replace the back door lock assembly with courtesy light switch.



c.
E407985C12
1.521,1.958 1.885,2.208 0.365,0.25 1.052,3.063 1.469,2.896 true 1.052,2.531 1.469,2.698 true 1.969,0.51 2.083,0.167 2.083,0.167 2.417,0.167 true 2.104,0.302 2.417,0.5 0.313,0.198 10 false *e 1.771,0.219 2.083,0.417 0.313,0.198 10 false *d 1.021,0.25 1.333,0.448 0.313,0.198 10 false *c 0.438,0.833 0.75,1.031 0.313,0.198 10 false *b 0.74,2.99 1.198,3.188 0.458,0.198 10 false CTY 0.865,2.448 1.323,2.646 0.458,0.198 10 false E 0.583,0.469 1.5,0.667 0.917,0.198 10 false 37°26' 1.333,0.25 2.25,0.448 0.917,0.198 10 false 37°23' 2.5,0.083 3.417,0.281 0.917,0.198 10 false 13°43' 0.74,1.875 1.052,2.073 0.313,0.198 10 false *a 1.615,1.99 1.927,2.188 0.313,0.198 10 false g6
*a Component without harness connected
(Back Door Lock Assembly with Courtesy Light Switch)
*b Open Position
*c Half-latch Position
*d Full-latch Position
*e Overstroke Position


Check the resistance of the full latch switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g6)Location & Routing

Click Connector(g6)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

g6-4 (CTY) - g6-1 (E) Open position Below 1 Ω
Half-latch position
Half-latch position → Full-latch position Below 1 Ω → 10 kΩ or higher
Full-latch position 10 kΩ or higher
Overstroke position


If the result is not as specified, replace the back door lock assembly with courtesy light switch.



d.
E407985C13
1.521,1.917 1.896,2.146 0.375,0.229 1.74,2.646 1.917,2.25 1.917,2.25 2.25,2.25 true 1.052,2.688 1.479,2.688 true 1.958,0.521 2.083,0.167 2.083,0.167 2.333,0.167 true 2.104,0.302 2.417,0.5 0.313,0.198 10 false *e 1.771,0.219 2.083,0.417 0.313,0.198 10 false *d 1,0.219 1.313,0.417 0.313,0.198 10 false *c 0.438,0.75 0.75,0.948 0.313,0.198 10 false *b 2.281,2.167 2.74,2.365 0.458,0.198 10 false POLE 0.917,2.615 1.375,2.813 0.458,0.198 10 false E 0.583,0.5 1.5,0.698 0.917,0.198 10 false 37°26' 1.333,0.25 2.25,0.448 0.917,0.198 10 false 37°23' 2.417,0.083 3.333,0.281 0.917,0.198 10 false 13°43' 0.833,1.917 1.146,2.115 0.313,0.198 10 false *a 1.635,1.938 1.948,2.135 0.313,0.198 10 false g6
*a Component without harness connected
(Back Door Lock Assembly with Courtesy Light Switch)
*b Open Position
*c Half-latch Position
*d Full-latch Position
*e Overstroke Position


Check the resistance of the pawl switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g6)Location & Routing

Click Connector(g6)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

g6-2 (POLE) - g6-1 (E) Open position 10 kΩ or higher
Open position → Half-latch position 10 kΩ or higher → Below 1 Ω → 10 kΩ or higher
Half-latch position 10 kΩ or higher
Half-latch position → Full-latch position 10 kΩ or higher → Below 1 Ω → 10 kΩ or higher
Full-latch position 10 kΩ or higher
Overstroke position


If the result is not as specified, replace the back door lock assembly with courtesy light switch.



e.
E407986C06
1.5,2.031 1.833,2.25 0.333,0.219 1.031,2.708 1.458,2.708 true 1.927,2.885 2.354,2.885 true 2.448,2.813 2.906,3.01 0.458,0.198 10 false OPN 0.875,2.635 1.333,2.833 0.458,0.198 10 false E 0.896,1.958 1.208,2.156 0.313,0.198 10 false *a 1.031,0.469 1.344,0.667 0.313,0.198 10 false *b 1.594,2.052 1.906,2.25 0.313,0.198 10 false g6
*a Component without harness connected
(Back Door Lock Assembly with Courtesy Light Switch)
*b Sector Gear in Neutral Position


Check the resistance of the sector switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g6)Location & Routing

Click Connector(g6)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

g6-6 (OPN) - g6-1 (E) Sector gear in neutral position
(Sector switch on)
Below 1 Ω
Sector gear not in neutral position
(Sector switch off)
10 kΩ or higher


If the result is not as specified, replace the back door lock assembly with courtesy light switch.